• 열처리공학회지
• /
• 제11권3호
• /
• pp.186-191
• /
• 1998

An oxidation behavior of 304 and 316 stainless steels were studied in dry air. After solution treatment, specimens were polished up to $1{\mu}m$ $A1_2O_3$ grade and then subjected to oxidation treatment in dry air at $800^{\circ}C{\sim}1200^{\circ}C$. The oxidation behavior between matrix and oxide scale was analyzed with SEM, EDS and XRD. When oxidation treatment was conducted at $1200^{\circ}C$, large thickness of Fe oxide scale was formed on top of surface and fine $(Cr,Fe)_2O_3$ oxide film was formed below it. Cr rich zone existed at interface between metal and $(Cr,Fe)_2O_3$ oxide layer, and it was believed that this zone acted as obstacle to oxidation. Most of Ni was detected at the interface between metal and $(Cr,Fe)_2O_3$ and also detected at the interface between $Fe_2O_3$ and $(Cr,Fe)_2O_3$.

• 설비공학논문집
• /
• 제24권3호
• /
• pp.281-287
• /
• 2012

The internal oxide scale of twelve superheater and reheater tubes were tested which were serviced for 30,000~120,000 hours in thermal power plants. The oxide scale was formed in three layers. The Cr-rich area was observed beneath the original metal surface. The hematite ($Fe_2O_3$) phase was formed on the outer surface. The intermediate layer was magnetite ($Fe_3O_4$). The thickness of Cr-rich layer was about half of the total scale. All layers grew during the operation hour of the plant. The thickness of thickest scale was 0.2mm in superheater tubes. This can increase the tube metal temperature about $7^{\circ}C$ more than initial state. $7^{\circ}C$ tube metal temperature can reduce tube life about 30%, but the boiler tube's design margin is big enough therefore it has been analyzed that it would not effect on the life span.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2011년도 춘계학술대회 및 Fine pattern PCB 표면 처리 기술 워크샵
• /
• pp.96-97
• /
• 2011

The T23 steel, whose composition was Fe-2.3%Cr-1.6%W, was arc-melted, and oxidized between $600^{\circ}C$ and $900^{\circ}C$ in air for up to 7 months. The amount of precipitates in the arc-melted microstructure was as large as 11.4 vol.%. The precipitates increased the oxidation rate of the arc-melted T23 steel. Owing to the low amount of Cr in the T23 steel, breakaway oxidation occurred after a few hours during oxidation above $700^{\circ}C$ in both arc-melted and as-received T23 steels. The scales that formed on arc-melted and as-received T23 steels were similar to each other. They consisted primarily of the outer $Fe_2O_3$ layer and the inner ($Fe_2O_3$, $FeCr_2O_4$)-mixed layer. The precipitates increased the microhardness and the oxidation rates.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1997년도 춘계학술발표회논문집(2)
• /
• pp.183-188
• /
• 1997

핵연료 피복관용 Zr신합금을 개발하기 위해서 16종의 신합금을 설계하였다. 설계된 합금은 진공아크용해, $\beta$-열처리, 열간압연, 냉간압연 및 진공열처리의 공정에 의해 판재로 제조되었으며 이들 시편에 대해 35$0^{\circ}C$와 40$0^{\circ}C$에서 부식시험, 상온과 고온에서 인장시험 및 40$0^{\circ}C$에서 크립시험을 실시하여 신합금의 특성을 평가하였다. Zr-Nb-Sn계에 Fe, V, Te, Sb, Ru, Pd의 다른 원소를 미량 첨가하는 다원계 합금에서 Fe와 Cr은 부식특성을 향상시키는데 매우 효과적인 것으로 나타났다. Sb는 기계적강도를 향상시키고 Fe, Cr원소는 연신율을 증가시키는 원소로 밝혀졌으며 Sb와 V은 크립저항성을 매우 향상시킨다. 16종의 합금중 2-3종의 합금은 기존의 Zircaloy-4보다 우수한 내식성을 보였으며 Zr-Nb-Sn-FeCr합금은 ZIRLO와 유사한 부식저항성을 나타냈다. 부식과 크립저항성을 동시에 향상시키기 위해서는 Fe, Cr, Sb원소를 적절히 함유시킨 합금에 대해서 집중적인 연구가 수행되어야 할 것으로 사료된다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2002년도 춘계 학술발표강연 및 논문개요집
• /
• pp.77-77
• /
• 2002

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2000년도 춘계학술발표회 초록집
• /
• pp.22-22
• /
• 2000

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1995년도 추계 학술발표 강연 및 논문개요집
• /
• pp.120-120
• /
• 1995

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 1999년도 춘계연구발표회 논문개요집
• /
• pp.102-103
• /
• 1999

• 한국전기화학회:학술대회논문집
• /
• 한국전기화학회 2004년도 춘계총회 및 학술발표회
• /
• pp.32-32
• /
• 2004

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 1996년도 춘계연구발표회 논문개요집
• /
• pp.34-35
• /
• 1996