• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.220-220
• /
• 2008

물 첨가 열화학기상증착을 이용하여 750도에서 길고 수직 성장한 다중벽 탄소나노튜브를 합성하였다. 사용된 기판으로는 우선 실리콘 웨이퍼에 열 증착기로 확산 방지층으로 Ti 50 nm를 입히고 그 위에 Al 15 nm를 입히고 난 후 촉매 층으로 Invar 36 (63 wt% Fe, 37 wt% Ni)을 1 nm 얇게 증착하였다. 탄소나노튜브의 성장에 사용된 가스는 Ar, $C_2H_2$ 이다. Ar은 분위기 가스로 사용되었고, $C_2H_2$는 탄소나노튜브의 성장에 관여하는 가스이다. 또한, 합성중에 약간의 물을 첨가함으로 기존의 탄소나노튜브 성장 길이보다 10배 가량 더 성장 하였다. 이것은 합성 중의 물 첨가로 인해 촉매 입자들의 활동성이 기존에 비해 더 증가했다는 것을 보여준다. 합성된 탄소나노튜브의 길이와 정렬도를 보기 위해 주사전자현미경 (scanning electron microscopy, SEM)을 이용하였고, 탄소나노튜브의 지름과 벽의 개수를 파악하기 위해 투과전자현미경 (transmission electron microscopy)을 이용하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.1
• /
• pp.129-138
• /
• 2001

This study examined the effects of the annealing heat treatments on the mechanical properties of the Invar(Fe-36%Ni Alloy) materials. Invar materials were annealed at various temperatures range 900~120$0^{\circ}C$ in vacuum(10-4Torr) and hydrogen atmospheres. And annealing conditions were changed by cooling rate and holding time at 110$0^{\circ}C$. The grain size of rolled Invar materials was very fine but those of annealed Invar materials at 900~120$0^{\circ}C$ in vacuum and hydrogen atmosphere increased with increasing annealing temperature. The micro-vickers hardness values of annealed Invar materials were decreased about 15% that of the rolled Invar materials, regardless of the various of annealing temperatures, atmosphere(vacuum, hydrogen) and annealing conditions. The tensile strength and yield strength of annealed Invar materials at 900~120$0^{\circ}C$ in vacuum and hydrogen atmosphere were decreased 10.0~14.4% and 34.6~39.1% those of the rolled Invar materials, respectively. The strength ratio(tensile strength/ yield strength) of annealed Invar materials was improved to 1.7~1.8 from the value of 1.2~1.3 of rolled Invar materials. The degree of spring back of annealed Invar materials was about 50% of the rolled Invar materials, regardless of the various of annealing temperatures, atmosphere(vacuum, hydrogen) and annealing conditions.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.10
• /
• pp.756-766
• /
• 2011

In order to investigate the degree of apartment parking lot dust contamination, total 72 samples of parking lot dust (36 from ground parking lots and 36 from the underground parking lots) were collected in Daegu city from the end of March to the early June 2010. The dust samples were sieved below $100{\mu}m$, and analysed by ICP for 14 elements after an acid extraction. Results obtained from the source assessment of trace element using enrichment factor showed that Fe, K, Mg, Mn, Na and V were influenced by natural sources, while Cd, Cr, Cu, Ni, Pb and Zn were influenced by anthropogenic sources in both the ground parking lot and the underground parking lot. And results showed that Ca were influenced by natural sources in the ground parking lot, but influenced by anthropogenic sources in the underground parking lot. The measured values were remarkably higher in components from natural sources than in components from anthropogenic sources. Underground parking lot dust was more affected by anthropogenic sources and contaminated compared with the ground parking lot dust. Pollution index of heavy metals revealed that underground parking lot dust was 5.5 times more contaminated with heavy metal components than the ground parking lot dust. The results of correlation analysis among trace elements indicated that components in the ground parking lot were more correlated than those in the underground parking lot, and especially more correlated with natural sources-natural sources. Analysis for correlations between components and influencing factors in the underground parking lot showed that concentrations of heavy metals were higher with smaller number of parking spaces and no ventilation system, and older apartments in last paint and cleaning had relatively higher contents of heavy metals than those of recently painted and cleaned.

• Journal of Radiation Protection and Research
• /
• v.36 no.4
• /
• pp.200-208
• /
• 2011

The neutron fluence measurement and evaluation technology is very important for material irradiation test. The most essential technology in this study is the neutron irradiation evaluation method using a fluence monitor. The fluence monitors were fabricated with metal wires of the purity ${\geq}$ 99.9%, whose dimensions were 0.1mm diameter, about 3 mm length, and around 150-200 ${\mu}g$ mass range. Three wire samples (Fe, Ni, Ti) were prepared for one irradiation aluminum capsule. Five capsules were irradiated in the OR5 hole of the HANARO reactor at 30 MW power for about 25 days. After irradiation tests, radiation activities were measured with the high purity germanium (HPGe) detector. The reaction rates were calculated by using the measured radiation activity data, and then neutron fluence were obtained from the reaction rates and the weighted neutron cross section with calculated neutron spectrum at the fluence monitor position.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.03a
• /
• pp.36-36
• /
• 2011

We synthesized new dye sensor based on indole compound. Through the UV-vis absorptions, we analyzed chemosensing properties to explain metal binding properties. The peak absorptions increased at 472 nm when added metal cations($Cd^{2+}$, $Cu^{2+}$, $Hg^{2+}$, $Fe^{2+}$, $Zn^{2+}$, $Ni^{2+}$ and $Cr^{3+}$) and gradually decreased the peak at 516 nm. Thus, this UV-Vis absorption behavior clearly showed the metal binding reaction. To measure energy level of used dye sensor, HOMO/LUMO energy value was calculated with cyclovaltagramm(CV) and using computational calculation method, in which we estimated the optimum structure of dye sensor. CV and computational calculation method, both compared to find suitable geometric structure. (with almost same energy values.) From the computational calculation, dye sensor has plane structure. So, Amine and ketone in the dye sensor faced each other and makes position to bind metal cations. In addition, these positions was supported pull-push electron system and generated MLCT process, when the dye sensor was bonded with the metal cations and resulted chemosensing properties. Through the electrochemical and computational calculation method analyze, we proposed the chemosensing principles that the dye sensor bind the metal cation between ketone and amine. Finally, the formation type of metal ion bindings was determined by Job's plot measurements.

• 한국해양학회지
• /
• v.22 no.3
• /
• pp.130-142
• /
• 1987

Sedimentological characteristics of the surface sediments in the southern sea off Cheju Island are described from analyses of bottom sediments. The sediments are subdivided into seven textural classes, muddy sand, slightly gravelly muddy sand, sand, clayey sand, sandy clay, sandymud, silty sand. Sand-size sediments are distributed in the southeastern part and/or around the Island, whereas sandy and muddy sediments are mainly distributed in the central and southern parts of the study area. A small portion of mud patch is located in the southwestern part of the area. According to the textural parameters analysis, sediments in the study area are poorly sorted(av.2.52 ), positive skewed(av.1.61 ), leptokurtic(av.1.74 ), transported by saltation and/or suspension, and roundness of quartz is varied from angular to surrounded, which suggesting that the depositional environment is not simple. The calcium carbonate content is on the average 26.99%, and commonly abundant in sand-size sediments, whereas organic matter content in the bulk sediment is on the average 6.70% and usually dominant in fine-grained sediments.Light minerals consist of quartz(av56.01%),Na-Ca feldspar(av.6.15%),K-feldspar(av.9.22%) and rock fragments(av28.11%).The contect onquartz and K-feldspar increases continuously away from the Cheju Island. As a result of geochemical analysis,concentrations of the elements are as follow:Zn:19.42-43.52 ppm (av.30.67ppm),Mn:50-304 ppm(av139.39ppm),Cr:3.54-10.68ppm(av6.50ppm),Pb:5.52-41.68ppm(av.15.60ppm), Co:7.08-14.68ppm (av.10.78ppm),Ni:19.70-42.42ppm(av.29.57ppm),Cu:3.14-9.12ppm(av.5.14ppm),Fe:0.48-2.08% (av1.22%),Ca:0.32-13.16%(av6.60%),Al:0.06-0.08%(av.0.27%),Mg:0.12-0.76%(av.0.53%)na:0.11-0.51%(av.0.36%) Ag:0.48-4.08ppm(av.1.22ppm).Among these elements,the content of Zn,Cu,Cr,Mn,Fe,Al,Mg,Pb and Na increase toward the southwestern area,while the content of Ca and Ag SHOWS the reversed distribution trend.Such a distribution pattern seems to imply that spatial distrivution of heavy metals is closely related to the variation in grain size. X-ray diffractogram show that the minerals in clay from the southwestern mud patch are illite ,chlorite, kaolinte,feldspar and calcite.The bulk of illite in th mud zone is believed to be originated from Huanghe and Yangytze River.The mud patch in this region contains the diagnostic calcite peak,and the concentration of Ca,ni,Pb,Ag are similar to Huanghe type,which indicates that the greater part of these clay fractions may have been derived from the Huanghe River.

• Ocean and Polar Research
• /
• v.36 no.4
• /
• pp.407-421
• /
• 2014

The benthic environmental impact experiment addresses environmental impacts at a specific site related to deep-sea mineral resource development. We have acquired several tens of multi- or box core samples at 31 sites within the Benthic environmental Impact Site (BIS) since 2010, aiming to examine the basic properties of surficial deep-sea sediment as a potential source for deep-water plumes. In this study, we present the geochemical properties such as major elements, rare earth elements (REEs), and heavy metal contents at the BIS. Such proxies vary distinctly according to the Facies association. The lithology of all core sediments in the BIS corresponds to both Association Ib and Association IIIb. The vertical profiles of some major elements ($SiO_2$, $Fe_2O_3$, CaO, $P_2O_5$, MgO, MnO) show noticeable differences between Association Ib and IIIb, while others ($Al_2O_3$, $TiO_2$, $Na_2O$, and $K_2O$) do not vary between Association Ib and IIIb. REEs are also distinctly different for Associations Ib and IIIb; in Association Ib, REY and HREE/LREE are uniform through the sediment section, while they increase downward in Association IIIb like the major elements; below a depth of 8 cm, REY is over 500 ppm. The metal enrichment factor (EF) evaluates the anthropogenic influences of some metals (Cu, Ni, Pb, Zn, and Cd) in marine sediments. In both Associations, the EF for Cu is over 1.5, the EF for Ni and Pb ranges from 0.5 to 1.5, and the EF for Zn and Cd are less than 0.5, indicating Cu is enriched but Zn and Cd are relatively depleted in the BIS. The vertical variations of geochemical properties between Association Ib and IIIb are shown to be clearly different, which seems to be related to the global climate changes such as the shift of Intertropical convergence zone (ITCZ).

• Resources Recycling
• /
• v.25 no.2
• /
• pp.33-41
• /
• 2016

A scale up tests (380 kg/day) using a continuous solvent extraction and electro-winning system was carried out to separate and recover cobalt from a solution containing 1.91 g/L Co and 14.65 g/L Ni. The solution was obtained during a process including solvent extraction and precipitation stages for removal of Cu and Fe from a synthetic sulfuric acid solution of manganese nodule matte. The optimal condition for solvent extraction was : solvent concentration of 0.22M Na-Cyanex 272 (45% saponified with NaOH) and O:A phase ratios of 1:1.5, 10:1 and 1.5:1 used in extraction, scrubbing and stripping stages, respectively. The extraction and stripping efficiencies were found to be 99.8% and 99.88%, respectively. The stripped solution contained 40.27 g/L Co with 4 ppm Ni. Cobalt metal of 99.963% purity was yielded with current efficiency of 67% and current density of $0.563A/dm^2$ during the electro-winning process.

• Korean Journal of Metals and Materials
• /
• v.47 no.2
• /
• pp.129-137
• /
• 2009

Corrosion behaviors of TiN coated dental casting alloys have been researched by using various electrochemical methods. Three casting alloys (Alloy 1: 63Co-27Cr-5.5Mo, Alloy 2: 63Ni-16Cr-5Mo, Alloy 3: 63Co-30Cr-5Mo) were prepared for fabricating partial denture frameworks with various casting methods; centrifugal casting(CF), high frequency induction casting(HFI) and vacuum pressure casting(VP). The specimens were coated with TiN film by RF-magnetron sputtering method. The corrosion behaviors were investigated using potentiostat (EG&G Co, 263A. USA) in 0.9% NaCl solution at $36.5{\pm}1^{\circ}C$. The corrosion morphologies were analyzed using FE-SEM and EDX. Alloy 1 and Alloy 2 showed the ${\alpha}-Co$ and ${\varepsilon}-Co$ phase on the matrix, and it was disappeared in case of TiN coated Alloy 1 and 2. In the Alloy 3, $Ni_2Cr$ second phases were appeared at matrix. Corrosion potentials of TiN coated alloy were higher than that of non-coated alloy, but current density at passive region of TiN coated alloy was lower than that of non-coated alloy. Pitting corrosion resistances were increased in the order of centrifugal casting, high frequency induction casting and vacuum pressure casting method from cyclic potentiodynamic polarization test.

• Journal of Welding and Joining
• /
• v.27 no.5
• /
• pp.74-80
• /
• 2009

The membrane of the LNG carriers consists of thin strips of INVAR(Fe-36%Ni) steel plates, and the junction between INVAR strips is fabricated by welding. Thousands of the raised edge joints, regularly spaced, are located around all the side of the tank corner near the transverse bulkhead, and TIG welding is manually made on the top of the raised edges. Since the thickness of all the laminated edge plies is extremely thin and the weld position is under a bad accessibility, highly skilled workers are required to perform welding relatively for a long welding time. An alternative scheme for the corner membrane fabrication is proposed in the study to improve the installation workability and thus productivity. The scheme replaces the welded edges with the preformed corrugation ones. A panel strip with regularly-spaced corrugations is installed at the corner instead of the individual flat strip of which edge is vertically raised to be welded with the adjacent strip. In the study, a series of the evaluation on the corrugated edge members was performed to assess the applicability to the real LNG carrier fabrication. Opening displacement at the raised edge was experimentally examined. Elastic stiffness regressed from the displacement was nearly same in both edge types. Edge displacement and local stresses were calculated under hydrostatic pressure and temperature change due to liquefied cargo. Fatigue test was performed on both corrugated and welded edge specimens consisting of two or five plies of invar strips. Fatigue strength of the corrugated specimens was not less than that of the welded specimens.