• Journal of the Korea Institute of Building Construction
• /
• 제23권6호
• /
• pp.663-671
• /
• 2023

This research experimentally evaluated the recyclability of four varieties of lignocellulosic fly ash(FA), a by-product from three power plants employing lignocellulosic biomass(Bio-SRF, wood pellets) as a fuel source. Comprehensive analyses were conducted on FA, encompassing both physical parameters (particle shape, size distribution, fineness, and density) and chemical properties(chemical composition and heavy metal content). Mortar test specimens, with FA mixing ratios ranging from 5 to 20%, were produced in compliance with KS L 5405 standards, and their flow and compressive strength were subsequently measured. The test results indicated that the four types of FA exhibited particle sizes approximately between 20~30㎛, densities around 2.3~2.5g/cm³, and a fineness range of 2,600~4,900cm²/g. The FA comprised approximately 50~90% of components such as SiO₂, Al₂O₃, Fe₂O₃, and CaO, displaying characteristics akin to type-II and type-III FA of KS L 5405 standards, albeit with differences in chlorine and SiO₂ content. From the mortar tests, it was observed that the compressive strength of the mortar ranged between 34~47MPa when the pellet combustion FA was mixed in proportions of 5~20%. FA, produced exclusively from the combustion of 100% lignocellulosic fuel, is assessed to possess high recyclability potential as a substitute for conventional admixtures.

• Korean Journal of Soil Science and Fertilizer
• /
• 제17권2호
• /
• pp.147-154
• /
• 1984

Two Fe-hydrous oxide A,B and one Al-hydroxide minerals were synthesized precipitating Fe $Cl_3$ and $AlCl_3$ with alkali solution(NaOH) at pH 6.0, 12.0 and 4.5 respectively, for precise understanding of physico-chemical and surface charge characteristics of soils in which these minerals are dominant. Identification of these final products, effect of free and amorphous materials on X-ray diffraction analysis, particle size distribution and surface change characterics of these minerals were performed. Fe-hydroxide A and B were identified as great deal of X-ray amorphous material and as goethite with large amount of X-ray amorphous material, respectively. Dehydration by oven at $105^{\circ}C$ of these minerals exhibited akaganeite peaks with low X-ray amorphous hump and pure goethite peaks for Fe-hydroxide A and B, respectively. Both minerals, however, turned into hematite upon firing at $550^{\circ}C$. On the other hand, Al-hydroxide identified as mixture of gibbsite and bayerite of around 7:3 ratio. Application of sodium dithionite and ammonium oxalate solutions for removal of free or amorphous Fe and Al from these minerals revealed that only peak intensities of Al-hydroxide system were enhanced upon Al-extraction by oxalate solution even though dithionite solution was much powerful to extract Fe from Fe-hydrous oxide systems. Original(wet) Fe-hydrous oxide A has the highest specific surface and surface charge development(negative and positive), and the greatest amount of less than $2{\mu}m$ sized particles. Specific surface and clay sized particles(less than $2{\mu}m$) of Fe-hydrous oxide A, however, were drastically reduced upon dehydration($P_2O_5$ and oven drying) compare to the rest minerals. The Z.P.C. of these synthetic minerals were 8.0-8.5, 7.5-8.0 and 5.5-6.0 for Fe-hydrous oxide A, B and Al-hydroxide, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제30권12호
• /
• pp.782-787
• /
• 2017

There is growing interest in power inductors in which metal soft magnetic powder and epoxy resin are combined. In this field, the process technology for increasing the packing density of magnetic particles in an injection molding process is very important. However, little research has been reported in this regard. In order to improve the packing density, we investigated and compared the sedimentation heights of pastes for three types of soft magnetic alloy powders as a function of the mixing ratios and the type of resin used. Experimental results showed that the packing density was the highest (71.74%) when the mixing ratio was 80 : 16 : 4 (Sendust : Fe-S : CIP) according to the particle size using an SE-4125 resin. In addition, the packing density was found to be inversely related to the layer separation distance. As a result, it was confirmed that the dispersion of solid particles in the paste was important for curing; however, the duration of the curing process can greatly affect the packing density of the final composite.

• Korean Journal of Materials Research
• /
• 제23권6호
• /
• pp.299-303
• /
• 2013

In this study, a micro gas sensor for $NO_x$ was fabricated using a microelectromechanical system (MEMS) technology and sol-gel process. The membrane and micro heater of the sensor platform were fabricated by a standard MEMS and CMOS technology with minor changes. The sensing electrode and micro heater were designed to have a co-planar structure with a Pt thin film layer. The size of the gas sensor device was about $2mm{\times}2mm$. Indium oxide as a sensing material for the $NO_x$ gas was synthesized by a sol-gel process. The particle size of synthesized $In_2O_3$ was identified as about 50 nm by field emission scanning electron microscopy (FE-SEM). The maximum gas sensitivity of indium oxide, as measured in terms of the relative resistance ($R_s=R_{gas}/R_{air}$), occurred at $300^{\circ}C$ with a value of 8.0 at 1 ppm $NO_2$ gas. The response and recovery times were within 60 seconds and 2 min, respectively. The sensing properties of the $NO_2$ gas showed good linear behavior with an increase of gas concentration. This study confirms that a MEMS-based gas sensor is a potential candidate as an automobile gas sensor with many advantages: small dimension, high sensitivity, short response time and low power consumption.

• Elastomers and Composites
• /
• 제47권4호
• /
• pp.318-328
• /
• 2012

In this study, the one-component curable polyurethane resin was manufactured using blocked isocyanate and hybrid technology. To prepare the one-component curable hybrid polyurethane, silica hybrids including hydroxyl group was synthesized, and the size, shape and distribution of hybrid particle in polyurethane resin were confirmed. Then the dissociation property, mechanical property and molding property of blocked isocyanate were investigated. The dissociation property of blocked isocyanate in one-component curable polyurethane became better as the heating temperature and treatment time increased. The synthesized silica hybrid had spherical appearance and size of 23~27 nm in diameter, and it was observed that the hybrid particles were homogeneously distributed in polyurethane structure. In the case of hybrid polyurethane, the mechanical property, anti-abrasion and thermal property were higher than those of general polyurethane, and it was observed that the mechanical property was maintained when the plasticizer was introduced.

• Korean Journal of Food Science and Technology
• /
• 제25권6호
• /
• pp.769-774
• /
• 1993

Defatted rice bran was microparticulated using fluidized bed opposed jet mill and air-classified at different air classifying wheel speed (ACWS) in Turboplex classifier. The median particle size and the standard deviation decreased, and concomitantly the specific surface area increased generally with increasing ACWS. The protein, fat and ash contents of the recovered rice bran increased with ACWS. The contents of minerals; magnesium, zinc, iron and manganese; increased positively with ACWS. The phytic acid content, however, was slightly higher at middle ACWS. The dietary fiber content was highest in the ACWS 15,000 rpm fraction showing 31.47%. Higher ACWS resulted in lighter colored powder. The water holding capacity (WHC) showed the maximum value at ACWS 12,000 rpm and decreased with increasing ACWS, while the oil holding capacity (OHC) increased with ACWS. The rheological property of the microparticulated rice bran/water suspension fitted to the linear model. The yield stress and viscosity of the suspension increased with ACWS. The shape of microparticulated rice bran at ACWS 21,000 rpm was spherical, and the median particle size was $3.7{\mu}m$. When cake was prepared with substitution of microparticulated rice bran at 5%, the cake height and volume increased remarkably.

• Journal of Korean Society for Atmospheric Environment
• /
• 제26권6호
• /
• pp.606-615
• /
• 2010

This study aims to identify the characteristics of soil in Mongolia, one of the major Asian dust sources that influence the Korean Peninsula. Soil particle size was analyzed and the result shows that sand (57.5~97.3%) was identified prominently in most regions, followed by silt (2.5~34.7%) and clay (0.0~7.8%). Soil pH of the covered regions were in the range 7.1~10.1, either weak alkaline or strong alkaline. Analysis of ion species in the soil samples exhibited that $Na^+$ ($91.9\;mg\;kg^{-1}$), $Cl^-$ ($65.9\;mg\;kg^{-1}$), and $Ca^{2+}$ ($53.5\;mg\;kg^{-1}$) were detected more in the soil than other species such as ${SO_4}^{2-}$ ($19.2\;mg\;kg^{-1}$), ${NO_3}^-$ ($46.6\;mg\;kg^{-1}$), ${NH_4}^+$ ($3.9\;mg\;kg^{-1}$), $K^+$ ($22.0\;mg\;kg^{-1}$), and $Mg^{2+}$ ($10.2\;mg\;kg^{-1}$). As for heavy metal content in the soil, concentrations of soil-borne metals including Fe, Al, Ca, Mg, and K tended to be high, while metals that come from manmade sources Pb, Cd, Cr, V, and Ni were remarkably low. The concentration of organic carbon (OC) was relatively high at $15.9\;{\mu}g\;mg^{-1}$, while elemental carbon (EC), directly released in the process of fossil fuel combustion, was not detected at all or found in very small amounts. The result indicates that pollution from manmade sources scarcely occurred. The analysis results from this study may contribute to improving modeling accuracy by providing input data for Asian dust prediction models, and be used as base data for determining the process of physiochemical transformation of Asian dust during long-range transport.

• Analytical Science and Technology
• /
• 제23권4호
• /
• pp.371-382
• /
• 2010

TSP and PM2.5 atmospheric aerosols have been collected at Gosan site of Jeju Island, and their compositions were analyzed to understand the pollution characteristics. The composition ratios of nss (non-sea salt)-$SO_4^{2-}$ and $NH_4^+$ were higher in Gosan site than those in other Korean background and urban sites. However the composition ratio of $NO_3^-$ was conversely lower in Gosan site. From the study of aerosol components according to particle sizes, the anthropogenic nss-$SO_4^{2-}$, $NO_3^-$ and $NH_4^+$ components were mostly existed in the fine particles. But the nss-$Ca^{2+}$, $Na^+$, $Cl^-$ and $Mg^{2+}$ originated from soil and marine sources were distributed relatively in the coarse particles. In the seasonal comparison, the concentrations of nss-$Ca^{2+}$, Al, Fe, Ca and $NO_3^-$ increased in spring season, and nss-$SO_4^{2-}$ showed higher concentration in summer and spring seasons. Based on the factor analysis, the atmospheric aerosols in Gosan site have been found to be influenced largely by anthropogenic sources, and next by marine and soil sources. The backward trajectory analyses showed that the concentrations of nss-$SO_4^{2-}$, $NO_3^-$, Pb and nss-$Ca^{2+}$ increased when the air mass moved from Chinese continent to Jeju area. On the other hand, their concentrations decreased when the air mass moved in from the North Pacific Ocean.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• 제16권3호
• /
• pp.101-105
• /
• 2006

We fabricated the nano $TiN_x$ by making of reaction between titanium powder and $Si_3N_4$ during planetary milling. The $TiN_x$ powder was sintered by spark plasma sintering machine after mixing with 50 wt% of titanium powder, and the sintered body was heat-treated at $850^{\circ}C$ in order to investigate its hardness property at the elevated temperature. We analyzed crystal structure by XRD. We observed the peaks of $TiN_{0.26}$ and TiN after 10 hours milling, and we observed TiN peak mainly after 20 hours milling. The reacted particle size distribution was investigated by FE-SEM. Increase of milling time, the size of reacted particles was decreased and the $10{\sim}20nm$ size of $TiN_x$ on the surface of titanium and $TiN_x$ was observed after 20 hours milling. The micro-Vickers hardness of mixed sintered body was about $1050kgf/mm^2$.

• Polymer(Korea)
• /
• 제35권1호
• /
• pp.66-71
• /
• 2011

With the synthesis of hyper crosslinked polymer particle (HCPP), having microporous structure with hydroxyl functional group, synthesized via polymerization reaction consists of three stepssuspension polymerization, hyper crosslinking by Friedel-Craft catalysis and hydrolysis reaction, the effects of the ratio of each monomer, hyper crosslinking conditions and $CO_2$ supercritical drying on the variations of surface morphology, pore size & distribution and BET surface area of HCPP have been investigated. It was observed that the formation of surface crack or fracture of HCPP was intimately related with the degree of hyper crosslinking reaction between microphase separated domains. And the value of BET surface area of HCPP increased with the increase of reaction temperature, time and the amounts of solvent used in hyper crosslinking step. Moreover, $CO_2$ supercritical drying was proven to be a very effective method for removing stabilizer, unreacted monomers and oligomers from HCPP but needed to add methanol as a co-solvent for efficient removing of residual catalyst.