• Wind and Structures
• /
• v.37 no.4
• /
• pp.289-302
• /
• 2023

Insulating glass units (IGUs) have been widely used in buildings in recent years due to their superior thermal insulation performance. However, because of the panel reciprocating motion and fatigue deterioration of sealants under long-term wind loads, many IGUs have the problem of early failure of watertight properties in real usage. This study aimed to propose a statistical method for wind-induced deflection of IGU panels during the whole life service period, for further precise analysis of the accumulated fatigue damage at the sealed part of the edge bond. By the estimation of the wind occurrence regularity based on wind pressure return period, the events of each wind speed interval during the whole life were obtained for the IGUs at 50m height in Beijing, which are in good agreement with the measured data. Also, the wind-induced deflection analysis method of IGUs based on the formula of airspace coefficient was proposed and verified as an improvement of the original stiffness distribution method with the average relative error compared to the test being about 3% or less. Combining the two methods above, the deformation of the outer and inner panes under wind loads during 30 years was precisely calculated, and the deflection and stress state at selected locations were obtained finally. The results show that the compression displacement at the secondary sealant under the maximum wind pressure is close to 0.3mm (strain 2.5%), and the IGUs are in tens of thousands of times the low amplitude tensile-compression cycle and several times to dozens of times the relatively high amplitude tensile-compression cycle environment. The approach proposed in this paper provides a basis for subsequent studies on the durability of IGUs and the wind-resistant behaviors of curtain wall structures.

• Journal of the Korean institute of surface engineering
• /
• v.51 no.5
• /
• pp.309-315
• /
• 2018

The purpose of this study is to assess the mechanical properties of the ceramic abutment with washer. In this study, ceramic abutment were used, tested with $30^{\circ}$ compression load, shear fatigue, adaptation accuracy test(rotation angle, contact interval), removal torque force test, torsional breaking force test. The $30^{\circ}$ compression load was 729 N, the shear fatigue load was 275 N, adaptation accuracy test of rotation angle was within $3^{\circ}$, contact interval within $10{\mu}m$, and removal torque force test value is $18.88N{\cdot}cm$, torsional breaking force test value is $35.52N{\cdot}cm$. Ceramic abutment with a washer fitted have sufficient mechanical strength and may be substituted for titanium abutment.

• The Korean Journal of Emergency Medical Services
• /
• v.17 no.2
• /
• pp.21-28
• /
• 2013

Purpose : The aim of the study is to compare the effect of cardiopulmonary resuscitation (CPR) with voice and CPR without voice by one rescuer. Methods : Subjects were 26 students in C University who had basic life support certificate for Healthcare Provider. They performed 30:2 CPR for 6 minutes by two groups of CPR with voice and CPR without voice by one rescuer from August 14 to 16, 2012. They performed CPR with Resusci Anne SkillReporter$^{TM}$ and Laerdal PC SkillReporting System Ver. 2.4.1(Laerdal Medical, Norway and recored voice using TES-1350A(TES Electrical Electronic Corp, Taiwan). Between each experiment, 1 day of rest was given, providing enough time to recover from the fatigue of CPR. Results : The depth, rate of chest compression, and ventilation volume were not affected by a voice (p >.05), and the ratio of chest compression to ventilation kept 30:2, when the subject made a sound (p <.05). Conclusion : Making voice during CPR was associated with an accurate ratio of 30:2 and the reduction in hands off time.

• Progress in Medical Physics
• /
• v.20 no.3
• /
• pp.119-124
• /
• 2009

Stents are frequently used throughout the human body. They keep pathways open in vascular or nonvascular duct for a long time. Therefore its stability is very important factor. In recent years, aconsiderable amount of research has been carried out in order to estimate mechanical properties of the stent such as expansion pressure behavior, radial recoil and longitudinal recoil using FEM (Finite element analyses). However, published works on simulation of stent fatigue behavior using FEM are relatively rare. In this paper, a nonlinear finite-element methodwas employed to analyses the compression of a stent using external pressure and fatigue behavior. Finite element analyses for the stent system were performed using NASTRAN FX. In conclusion this paper shows how the stent is behaved in the body, and its fatigue behavior.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.3
• /
• pp.427-431
• /
• 2007

The safety and the durability of the arm as an automotive chassis part under the fatigue can be predicted in this study. The fatigue life is sharply decreased from 0.5 to 0.75 at the change of load which is the amplitude load divided by average load. But its life is slightly decreased at the change of load from 0.75 to 1.5. The influence of fatigue life according to the change of load can be predicted by these results. As the value of maximum damage is 2.2 and the value of maximum compressive strain or stress is $-6.93{\times}10^{-3}$ or 349 Mpa at the connected part of rod end applied by concentrated load respectively, there is the greatest possibility of destruction due to the compression at this part.

• Fashion & Textile Research Journal
• /
• v.25 no.4
• /
• pp.508-519
• /
• 2023

Muscle reduction owing to aging causes changes in physical function among the elderly. Fitness compression wear reduces fatigue by compressing the main muscles, expanding blood vessels, and rapidly discharging lactic acid. The effect of clothing pressure when wearing fitness compression wear for the elderly was objectively and subjectively evaluated for six women aged 55-64 years. The evaluation clothes were three types of tops and bottoms, one type of design (A) preferred among the existing compression wear, and two types of design (B and C). The objective evaluation items included clothing pressure, blood flow, surface temperature, and subjective satisfaction. It was found that clothing A had the highest clothing pressure in the straight posture and five fitness movements. Blood flow increased the most when wearing the evaluation clothing. The surface temperature was found to be the highest for clothing C, and subjective satisfaction was found to be the best when wearing evaluation clothing B. If the tensile strength was low and the tensile elongation was high, as in evaluation clothing B, it was recognized as appropriate clothing pressure, and the subject was subjectively satisfied. When manufacturing fitness compression wear in the future, it will be possible to increase users' objective and subjective satisfaction with wearing it, if the incision of the garment were placed at the location of the line of non-extension (LoNE), and appropriate material characteristics are applied.

• Structural Engineering and Mechanics
• /
• v.29 no.3
• /
• pp.301-310
• /
• 2008

Applications of fracture mechanics in the strength analysis of ceramic materials have been lately studied by many researchers. Various test specimens have been proposed in order to investigate the fracture resistance of cracked bodies under mixed mode conditions. Double Cleavage Drilled Compression (DCDC) specimen, with a hole offset from the centerline is a configuration that is frequently used in subcritical crack growth studies of ceramics and glasses. This specimen exhibits a strong crack path stability that is due to the strongly negative T-stress term. In this paper the maximum tensile stress (MTS) criterion is employed for investigating theoretically the initiation of brittle fracture in the DCDC specimen under mixed mode conditions. It is shown that the T-stress has a significant influence on the predicted fracture load and the crack initiation angle. The theoretical results suggest that brittle fracture in the DCDC specimen is controlled by a combination of the singular stresses (characterized by KI and KII) and the non-singular stress term, T-stress.

• Proceedings of the KWS Conference
• /
• 1999.05a
• /
• pp.233-236
• /
• 1999

The welding residual stress should be considered in fatigue stress analysis because it develope during the process of the electric resistance spot welding and it causes bad affect on the fatigue crack initiation and growth at nugget edge of spot welded points. Therefore the accurate estimation of residual stress is crucial. In this study, nonlinear finite element analysis on welding residual stress generated during the process of the spot welding was conducted, and their results were compared with the experimental data measured by X-ray diffraction method. From the results, it was found that welding residual stress existed as tension in the nugget center and as compression around the nugget edge.

• Journal of Biomedical Engineering Research
• /
• v.26 no.2
• /
• pp.123-127
• /
• 2005

Compression Hip Screw (CHS) is one of the most widely-used prostheses for the treatment of intertrochanteric fractures because of its strong fixation capability. Fractures at the neck and screw holes are frequently noted as some of its clinical drawbacks, which warrant more in-depth biomechanical analysis on its design variables. The purpose of this study was to evaluate changes in the strength with respect to the changes in design such as the plate thickness and the number of screw holes. Both mechanical test and FEM analysis were used to systematically investigate the sensitivities of the above-mentioned design variables. For the first part of the mechanical test, CHS (n=20) were tested until failure. The CHS specimens were classified into four groups: Group Ⅰ was the control group with the neck thickness of 6-㎜ and 5 screw holes on the side plate, Group Ⅱ 6-㎜ thick and 8 holes, Group Ⅲ 7.5-㎜ thick and 5 holes, and Group Ⅳ 7.5-㎜ thick and 8 holes. Then, the fatigue test was done for each group by imparting 50% and 75% of the failure loads for one million cycles. For the FEM analysis, FE models were made for each group. Appropriate loading and boundary conditions were applied based on the failure test results. Stresses were assessed. Mechanical test results indicated that the failure strength increased dramatically by 80% with thicker plate. However, the strength remained unchanged or decreased slightly despite the increase in number of holes. These results indicated the higher sensitivity of plate thickness to the implant strength. No fatigue failures were observed which suggested the implant could withstand at least one million cycles of fatigue load regardless of the design changes. Our FEM results also supported the above results by showing a similar trend in stress as those of mechanical test. In summary, our biomechanical results were able to show that plate thickness could be a more important variable in design for reinforcing the strength of CHS than the number of screw holes.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.5
• /
• pp.835-842
• /
• 2002

In this paper, static and fatigue bending strengths and failure mechanisms of CFRP (carbon fiber reinforced plastics) laminates having impact damages have been evaluated. Composite laminates used for this experiment are CF/EPOXY orthotropy laminated plates, which have two-interfaces $[0^0_ 4/90^0_4]_{ sym}$. A steel ball launched by the air gun collides against CFRP laminates to generate impact damages. The damage growth during bending fatigue test is observed by the scanning acoustic microscope (SAM) and also, the fracture surfaces were observed by using the SEM (scanning electron microscope). In the case of impacted-side compression, fracture is propagated from the transverse crack generated near impact point. On the other hand, fracture is developed toward the impact point from the edge of interface-B delamination in the case of impacted-side tension. Eventually, failure mechanisms have been confirmed based on the observed delamination areas and fracture surfaces.