• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.713-718
• /
• 2006

In this study, temperature sensors were adhered to transformer that is used in KHST(Korean High-Speed Train) to verify variation of temperature characteristics about transformer synthetically and efficiently. In the case that temperature of transformer exceeds reference temperature for running of KHST, overheating of transformer may cause a fatal accident of vehicle. Characteristics and main specifications of transformer in KHST were described in this paper. Also, measuring system for temperature measurement of transformer was explained in brief. Temperature data of transformer was acquired using measuring system, KRRI(Korea Railroad Research Institute) analyzed characteristic in contrast with comparing with temperature of transformer about month, running speed and running time.

• Proceedings of the KSR Conference
• /
• 2002.10a
• /
• pp.31-37
• /
• 2002

Rail cars are subject to vibration, impact and wear which can cause severe defects leading to a fatal accident. Thus, they are designed and manufactured in consideration of such factors influencing their service lifetime. Under-frames are composed of steel and support most of load imposed on the car. Steel is very sensitive to corrosive environment and corroded even in a normal service condition. Regular maintenance can Protect steel Parts from corrosion by painting. However, an exposure of defect point to corrosive agents can make corrosion proceed to a considerable depth, which may cause the structure to remain under safety standard. It is necessary to understand corrosion behavior of rail cars in order to estimate unexpected accidents by corrosion.

• Journal of Trauma and Injury
• /
• v.36 no.4
• /
• pp.411-415
• /
• 2023

An odontoid process fracture is a serious type of cervical spine injury. This injury is categorized into three types based on the location of the fracture. Severe or even fatal neurological deficits can occur due to associated cord injury, which can result in complete quadriplegia. Computed tomography is the primary diagnostic tool, while magnetic resonance imaging is used to evaluate any associated cord injuries. These injuries can occur either directly from the injury or during transportation to the hospital if mishandled. There are two main treatment approaches: surgical fixation or external nonsurgical fixation, with various types and models of fixation devices available. In this case study, computed tomography follow-up confirmed that external fixation can yield successful results in terms of complete healing, even in cases complicated by other factors that may impede healing, such as pregnancy.

• Journal of the Korean Society of Industry Convergence
• /
• v.27 no.4_2
• /
• pp.885-895
• /
• 2024

As the lack of management for HAZMAT transportation leads to fatal accidents, the interest in the problem is rapidly increasing in the world. Thus UN-RTDG recommends to establish regulations for HAZMAT transportation, and related ministries in Korea make rules and policies according to the regulations. However, there are few researches carried out on railway HAZMAT transportation. In this paper, issues such as present condition of laws and policies related to railway HAZMAT transportation, HAZMAT transportation procedure and regulations, HAZMAT signs of railway etc. are analyzed. Through analyzing these issues the problems and improvements of railway HAZMAT transportation are drawn. These results are respected to help to establish regulations and policies for HAZMAT transportation management. In the future, more detailed plan is needed for putting these improvements to practices.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.18 no.4
• /
• pp.58-70
• /
• 2019

In the case of a pedestrian traffic accident, it has a large-scale danger directly connected by a fatal accident at the time of the accident. The domestic ITS is not used for intelligent risk classification because it is used only for collecting traffic information despite of the construction of good quality traffic infrastructure. The CNN based pedestrian detection classification model, which is a major component of the proposed system, is implemented on an embedded system assuming that it is installed and operated in a restricted environment. A new model was created by improving YOLO's artificial neural network, and the real-time detection speed result of average accuracy 86.29% and 21.1 fps was shown with 20,000 iterative learning. And we constructed a protocol interworking scenario and implementation of a system that can connect with the ITS. If a pedestrian accident prevention system connected with ITS will be implemented through this study, it will help to reduce the cost of constructing a new infrastructure and reduce the incidence of traffic accidents for pedestrians, and we can also reduce the cost for system monitoring.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.9
• /
• pp.740-746
• /
• 2013

Design with crashworthiness concept has been emphasized for almost aircraft and motor vehicles. However, crashes accompanied serious injury and death have been continuously occurred, and will be occurred subsequently. What was worse, it is a well-known fact that there were a good many crashes classified as survivable accidents in which fatal injuries were reported. But we cannot say that fatal injuries were inevitable consequences of those crashes. If crashworthy design for seat, restraint systems, and cabin strength were adequate or right, survivability in a crash event could be maximized greatly. To substantiate the right crashworthiness, we must thoroughly understand the characteristics of human tolerance under abrupt acceleration change, and the cabin design should be combined with proper use of energy absorbing technologies that reduce accelerations experienced by the occupants. In this paper, the emphasis on the human tolerance under abrupt accelerations as well as the necessity of change in design requirements for crash environment will be stressed to widen the belt of consensus for the right crashworthy design.

• Journal of Chest Surgery
• /
• v.19 no.3
• /
• pp.421-428
• /
• 1986

From January 1981 through December 1985, 481 thoracic civilian injuries were reviewed in the Department of Thoracic Surgery, Paik Hospital in Seoul. Sixty two percent of the injuries were caused by traffic accident, 18% fall down, 15% blunt trauma, 2% crushing injury, 2% stab wound, and 0.4% gunshot wound. Peak incidence of the trauma victim was fourth and fifth decades revealing 22% and 27% respectively. Sex ratio was 3.5:1 with male predominance. Elapsed time before admission was less than one hour in 36% and one to six hour in 30%. The types of the injuries were as follows: Non-penetrating injuries were the most part of the wounded, 97.6%. Rib fracture was the most common lesion occupying 292 patient out of 481 [61%]. Of these 292 patients, 72% was multiple rib fracture. The incidence of hemothorax or hemopneumothorax was 19% [102 patients] [Table 4]. Most common associated condition was head injuries, 98 patients [14%]. Thoracoabdominal injuries were seen in 31 patients [0.6%]. Tube thoracostomy was the definitive measures in the 20% of the wounded. Open thoractomy was performed in 5%. Additional procedures for the associated condition were done in the 16% of the cases, for example, reduction of long bone fracture and trephination for the head injury. Among 481 wounded, fatal complication occurred in 13 patients [2.7%]. This paper has also compared two series of patients according to period; one from 1970 to 1980 and the present series [Table 8]. Conclusively, the fatal complications or trauma death may be reduced by the effort 1] rapid transport of the victim, 2] initial correction or resuscitative measures of the circulatory and ventilatory deficit 3] early decision of definitive thoracostomy or thoracotomy and 4] proper prioritizing for the care of the multiple critically injured patient.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.3
• /
• pp.163-170
• /
• 2000

Accident statistics shows that the portion of fatal occupant injuries due to side impacts is considerably high. The side impact usually leads to a severe intrusion of side structure into the passenger compartment. Furthermore, the safety zone for the side impact is relatively small compared to the front impact. Those kinds of physics for side impact frequently result in a fatal injury for the occupant. Therefore, NHTSA and EEVC are trying to intensify the regulation for the occupant protection against side impact. Both the regulation and recent market trends are asking for an installation of side airbag. There are several types of system configuration for side impact sensing. In this paper, we adopt the acceleration-based remote sensing method for the side airbag control system. We mainly focus on the development of hardware and crash discrimination algorithm of remote sensing unit. The crash discrimination algorithm needs fast decision of airbag firing especially for high-speed side impact such as FMVSS 214 and EEVC tests. It is also required to distinguish between low-speed fire and no-fire events. The algorithm should have a sufficient safety margin against any misuse situation such as hammer blow, door slam, etc. This paper introduces several firing criteria such as acceleration. velocity and energy criteria that use physical value proportional to crash severity. We have made a simulation program by using Matlab/Simulink to implement the proposed algorithm. We have conducted an algorithm calibration by using real crash data for 2,500cc vehicle. The crash performance obtained by the simulation was verified through a pulse injection method. It turned out that the results satisfied the system requirements well.

• Korean Journal of Construction Engineering and Management
• /
• v.8 no.2
• /
• pp.68-74
• /
• 2007

It has been recognized that safety management is activated during the construction phase to prevent accidents and fatalities of workers. However, It is revealed that about 15% of fatal death accidents is caused by the lack of management of planning and design phases. There is a crucial need of assessing safety risk during building design phase. This paper is aimed to develop a safety risk assessment checklist that can be used during building design phase, utilizing the concept of Design for Safety. In doing so, a broad literature survey on safety management of building Process, various safety risk assessment toolboxes being utilized in the HSE and the BAA of UK. The proposed checklist contains the followings: 1) classification structure for safety design on space, element, and trade work 2) hazard risk factor, probability and degree of intensity of accident occurrence, and 3) safety assessment criteria. It is expected that the checklist would be an effective tool of preventing and minimizing fatal accidents of building construction projects.

• Journal of the Korea Institute of Building Construction
• /
• v.19 no.4
• /
• pp.341-350
• /
• 2019

Construction industry is one of the most dangerous industry. As the construction accidents occur due to the repeated factors found in each accidents, there is a limitation in analyzing all types of occupational accidents by the existing descriptive analysis and statistical test. In this study, we classified safety accidents caused by falling objects among the accident types occurring at construction sites into fatal and nonfatal accidents and deduced the factors. In addition, we deduced the association rules among the safety accidents factors caused by falling objects through the association rule analysis method among the machine learning techniques. Therefore, considering the association rules for fatal and nonfatal accidents proposed in this study, it would be possible to prevent accidents by searching for countermeasures against safety accidents caused by falling objects.