• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.12
• /
• pp.3235-3245
• /
• 1996

A DDFS(Direct Digital Frequency Synthesizer) used in spread spectrum communication systems must need fast switching speed, high resolution(the step size of the synthesizer), small size and low power. The chip has been designed with four parallel sine look-up table to achieve four times throughput of a single DDFS. To achieve a high processing speed DDFS chip, a 24-bit pipelined CMOS technique has been applied to the phase accumulator design. To reduce the size of the ROM, each sine ROM of the DDFS is stored 0-.pi./2 sine wave data by taking advantage of the fact that only one quadrant of the sine needs to be stored, since the sine the sine has symmetric property. And the 8 bit of phase accumulator's output are used as ROM addresses, and the 2 MSBs control the quadrants to synthesis the sine wave. To compensate the spectrum purity ty phase truncation, the DDFS use a noise shaper that structure like a phase accumlator. The system input clock is divided clock, 1/2*clock, and 1/4*clock. and the system use a low frequency(1/4*clock) except MUX block, so reduce the power consumption. A 107MHz DDFS(Direct Digital Frequency Synthesizer) implemented using 0.8.mu.m CMOS gate array technologies is presented. The synthesizer covers a bandwidth from DC to 26.5MHz in steps of 1.48Hz with a switching speed of 0.5.mu.s and a turing latency of 55 clock cycles. The DDFS synthesizes 10 bit sine waveforms with a spectral purity of -65dBc. Power consumption is 276.5mW at 40MHz and 5V.

• Journal of IKEEE
• /
• v.12 no.4
• /
• pp.255-262
• /
• 2008

In this paper, we proposed the novel IGBT with an additional n-type MOS structure to achieve the improved trade-off between turn-off and on-state voltage drop(Vce(sat)). These low on-resistance and the fast switching characteristics of the proposed IGBT are caused by an enhanced electron current injection efficiency which is caused by additional n-type MOS structure. In the simulation result, the proposed IGBT has the lower on state voltage of 2.65V and the shorter turn-off time of 4.5us than those of the conventional IGBT(3.33V, 5us).

• Journal of the Korean Institute of Intelligent Systems
• /
• v.12 no.2
• /
• pp.164-170
• /
• 2002

Sliding mode control, as a typical method of variable structure control, has the robust characteristics for the uncertainty and the disturbance of the nonlinear system. Because, however, sliding mode control input includes a sign function that Is discontinuous on the predefined switching surface, its applications are primarily limited by the need of alleviation or reduction of chattering. In this paper, we propose a chattering alleviation strategy based on a special nonlinear function and a fuzzy system. By using the proposed control scheme, we can reduce the steady state error. Its tracking performance is as fast as that of conventional method using the fixed boundary layer. Especially, in the proposed method, we can adjust the trade-off between the steady state error and the degree of chattering by regulating the proper range of the output variable of the fuzzy system. To verify the validity of the proposed algorithm, the analysis of the control method using the fixed boundary layer and the computer simulations are shown to compare with them.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.5
• /
• pp.25-31
• /
• 2007

This paper presents a comparison of different current controller response characteristics of SRM. The most common current controllers of the SRM is hysteresis type. The hysteresis controller is easy to implement and fast current control response, but has the inherent disadvantage of switching frequency variations. The other common type of current controller is PI scheme. The design of a classical PI current controller with fixed parameters for SRM is not an easy task due to the extreme nonlinear characteristics. In this paper, some linearization technique is used for design of PI current controller. Experimental results of 1-hp SRM are presented for the basic reference data which can be used to select the proper current control scheme according to the applications.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.5
• /
• pp.162-168
• /
• 2004

Service restoration is an emergency control in distribution control centers to restore out-of-service area as soon as possible when a fault occurs in distribution networks. Therefore, it requires fast computation time and high quality solutions for load balancing. In this paper, a load balance index and heuristic guided best-first search are proposed for these problem. The proposed algorithm consists of two parts. One is to set up a decision tree to represent the various switching operations available. Another is to identify the most effective the set of switches using proposed search technique and a feeder load balance index. Test results on the KEPCO's 108 bus distribution system show that the performance is efficient and robust.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.2
• /
• pp.332-338
• /
• 2010

Annually, electrical fires caused by arcing phenomena in power system rapidly increase as the use of more electric appliances, but there is no established method for the prevention of the accidents. With this background, this paper dealt with the experimental results on a series arc detection technique and a device for air conditioners. Series arcing phenomena that is generated in incomplete connection of air conditioners was simulated, and the frequency spectrum was analyzed. The Fast Fourier Transform (FFT) of the arc pulse showed that the dominant frequency components exist in ranges of 190 kHz~250 kHz and 900 kHz~1.6 MHz. An arc detection circuit with low cut off frequency of 170 kHz to attenuate 60 Hz by 170 dB and a signal discriminator were designed. Also, an algorithm which separate series arc signal from unwanted noises produced by switching operation, inverter, and surge was proposed. Application experiment was carried out on several types of air-conditioners by using the arc generator specified in UL1699, and the results showed the over 99 % accuracy.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.3
• /
• pp.7-17
• /
• 2014

Power electronics modules are semiconductor components that are widely used in airplanes, trains, automobiles, and energy generation and conversion facilities. In particular, insulated gate bipolar transistors(IGBT) have been widely utilized in high power and fast switching applications for power management including power supplies, uninterruptible power systems, and AC/DC converters. In these days, IGBT are the predominant power semiconductors for high current applications in electrical and hybrid vehicles application. In these application environments, the physical conditions are often severe with strong electric currents, high voltage, high temperature, high humidity, and vibrations. Therefore, IGBT module packages involves a number of challenges for the design engineer in terms of reliability. Thermal and thermal-mechanical management are critical for power electronics modules. The failure mechanisms that limit the number of power cycles are caused by the coefficient of thermal expansion mismatch between the materials used in the IGBT modules. All interfaces in the module could be locations for potential failures. Therefore, a proper thermal design where the temperature does not exceed an allowable limit of the devices has been a key factor in developing IGBT modules. In this paper, we discussed the effects of various package materials on heat dissipation and thermal management, as well as recent technology of the new package materials.

• Journal of IKEEE
• /
• v.14 no.1
• /
• pp.55-64
• /
• 2010

In this paper, we proposed the novel TIGBT with an additional p-type MOS structure to achieve the improved trade-off between turn-off and on-state voltage drop(Vce(sat)). These low on-resistance and the fast switching characteristics of the proposed TIGBT are caused by an enhanced electron current injection efficiency which is caused by additional p-type MOS structure. In the simulation result, the proposed TIGBT has the lower on state voltage of 1.67V and the shorter turn-off time of 3.1us than those of the conventional TIGBT(2.25V, 3.4us).

• Journal of Korea Multimedia Society
• /
• v.10 no.3
• /
• pp.348-357
• /
• 2007

One of the major issues in recent researches on wireless sensor networks is to reduce energy consumption of sensor nodes operating with limited battery power, in order to lengthen their lifespan. Among the researches, we are interested in the schemes in which a sensor node periodically turns on and off its radio and requires information on the time when its neighbors will wake up (or turn on). Clock synchronization is essential for wakeup scheduling in such schemes. This paper proposes three methods based on the asynchronous averaging algorithm for clock synchronization in sensor nodes which periodically wake up: (1) a fast clock synchronization method during an initial network construction period, (2) a periodic clock synchronization method for saving energy consumption, and (3) a decision method for switching the operation mode of sensor nodes between the two clock synchronization methods. Through simulation, we analyze maximum clock difference and the number of messages required for clock synchronization.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.6
• /
• pp.1253-1259
• /
• 2005

This paper dealt with the development of surge protection devices (SPDs) that can protect high speed computer network devices from overvoltages caused by switching operations or lightning surges. The designed SPD is a form of hybrid circuit which is composed of a gas tube having large current diverting capability, high response bi-directional avalanche diodes, and fast recovery diodes to reduce insertion loss on high frequency domain. Surge protection and signal transmission characteristics of the fabricated SPD was tested according to the international standards, IEC 61000-4-5 and IEC 61643-21. From the test results, the SPD is satisfied with the international standards and the high cut-off frequency was 204 MHz. Also, the SPD showed a good performance without an insertion loss on a field test of 100 Mbps class Local Area Network.