• Journal of the Korean Wood Science and Technology
• /
• v.44 no.3
• /
• pp.350-359
• /
• 2016

We performed fast pyrolysis of empty fruit bunch (EFB) in the range of temperature from $400{\sim}550^{\circ}C$ and 1.3 s of residence time. The effect of temperature on the yields and physicochemical properties of pyrolytic products were also studied. Elemental and component analysis of EFB showed that the large amount of potassium (ca. 8400 ppm) presents in the feedstock. Thermogravimetric analysis suggested that the potassium in the feedstock catalyzed degradation of cellulose. The yield of bio-oil increased with increasing temperature in the range of temperature from $400{\sim}500^{\circ}C$, while that of gas and biochar decreased and showed monotonous change each with increasing temperature. When the EFB was pyrolyzed at $550^{\circ}C$, the yield of bio-oil and char decreased while that of gas increased. Water content of the bio-oils obtained at different temperatures was 20~30% and their total acid number were less than 100 mg KOH/g oil. Viscosity of the bio-oils was 11 cSt (centistoke), and heating value varied from 15 to 17 MJ/kg. Using GC/MS analysis, 27 chemical compounds which were classified into two groups (cellulose-derived and lignin-derived) were identified. Remarkably the concentration of phenol was approximately 25% based on entire chemical compounds.

• Journal of Pharmaceutical Investigation
• /
• v.26 no.1
• /
• pp.1-11
• /
• 1996

Biphenyldimethyldicarboxylate (PMC), which has been used to treat hepatitis, is insoluble in water, therefore it has low bioavailability after oral administration. For the purpose of increasing the dissolution rate of PMC, the physical mixtures and inclusion complexes of PMC and $dimethyl-{\beta}-cyclodextrin\;(DM\;{\beta}CD)\;or\;hydroxypropyl-{\beta}-cyclodextrin\;(HP{\beta}CD)$ in molar ratio of 1 : 1 and 1 : 2 were prepared by solvent evaporation method. Mixed micelles of PMC were prepared by reacting PMC with bile salts [sodium cholate(NaC), sodium glycocholate (NaGC)] and oleic acid (OA) or palmitoylcarnitine chloride(PCC). Chloroform/water partition coefficient (PC) of PMC was 36.14 in artificial gastric juice (AGJ) and 33.47 in artificial intestinal juice (AIJ), respectively, on the other hand octanol/water PC was 63.36. PMC formulation was prepared by reacting PMC with PEG400-glycerin system(95 : 5, 90 : 10, respectively) and PEG400-PEG4000-glycerin system (70 : 25 : 5, 65 : 25 : 10, respectively). Dissolution test was performed in AGJ and AIJ by paddle method at $37{\pm}0.5^{\circ}C$. The dissolution rates of PMC tablets on the market were 5.74% and 8.26% at AGJ and AIJ, respectively and marketed PMC capsules were 22.14% and 28.64% at AGJ and AIJ, respectively. The dissolution rates of inclusion complexes of PMC with $DM{\beta}CD$ and $HP{\beta}CD$ in a molar ratio of 1 : 1 were more fast than those of corresponding physical mixtures. The decreasing order of dissolution rates was as follows; PMC-PEG400-PEG4000-glycerin formulation > PMC-PEG400-glycerin formulation > mixed micelles > CD inclusion complexes. The dissolution rates of PMC-PEG400-glycerin and PMC-PEG400-PEG4000-glycerin formulation were most fast and the percentage of dissolution was almost 100% within 20 minutes. And their dissolution rates after 120 minutes were markedly increased as compared with capsules on the market (4.0-fold and 3.2-fold in PMC-PEG400-glycerin formulation at AGJ and AIJ, respectively, and 4.8-fold and 3.7-fold in PMC-PEG400-PEG4000-glycerin formulation at AGJ and AIJ, respectively).

• Korean Journal of Environmental Agriculture
• /
• v.17 no.4
• /
• pp.371-378
• /
• 1998

Pesticide has played important role in Korean and Austrailian agriculture. In addition, pesticides are the most reliable tools pests in agriculture. Recently, it is highly recommended that the use of pesticide should be concerned with both atricultural and environmental aspect, also legislation on environmental contamination has been fortified to the world. Particularly, the attention on agrochemicals has been focused on the soil abuse and the water contamination at present time. In spite of this kind of concern, a few research about pesticides using in Australia and Korean have been conducted to their behaviors under australian and korean environment to avoid environmental contamination by pesticides. Thus, the research organizations need facilities to analyze the characteristics of each pesticide and the environmental fate of pesticides. The conventional analytical method to detect pesticides and their metabolites can not be overcome to reduce time, expenditure, and complexity of analysis even though the methods are accurate and precise. For example, High performance liquid chromatography(HPLC), and gas chromatography (GC) used until now are less choice detectors and often lower sensitive. In contrast to the conventional analytical methods, biosensors are so fast in analysis and has high productivity and analyze multi=sample simultaneously. Therefore, it is biosensing analytical method that we could consider as an alternative method intead of the conventional methods.

• Journal of the Korean Society of Tobacco Science
• /
• v.29 no.2
• /
• pp.140-145
• /
• 2007

Acrylamide has been found in many foods. Acrylamide in foodstuffs were analyzed by a GC/MS after bromination of acrylamide or by a LC/MS for underivatized acylamide. Time consuming and laborious clean up procedures is applied for the purification of the extract, in these methods. In this study, a simple and fast method without clean up step for the analysis of acrylamide in mainstream cigarette smoke was developed by using liquid chromatography-tandem mass spectrometry (LC/MS/MS) and the effects of tobacco leaf constituents on acrylamide content was observed. The analysis of acrylamide in mainstream cigarette smoke started to collect TPM (total particulate matter) from smoking and to extract by 0.1 % acetic acid solution and then to detect by liquid chromatography tandem mass spectrometry using electrospray in the positive mode. The recovery of acrylamide in 2R4F reference cigarette was 98 % and the reproducibility was 2.5 % and the limit of detection was 1.6 ng/mL. Reducing sugars and amino acids are considered to be main precursors of acrylamide in foodstuffs. Cut tobacco contain substantial amounts of reducing sugars and amino acid which may be explained the occurrence of acrylamide in mainstream cigarette smoke. The effects of reducing sugars and total nitrogen studied in an experiment with a various tobacco types. This result indicated that reducing sugars are not limiting factor for acrylamide formation, but the level of acrylamide in cigarette smoke was significantly correlated with the total nitrogen contents.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.61 no.1
• /
• pp.64-69
• /
• 2016

This study was conducted to develop a fast and efficient screening method to determine the quantity of fatty acid in peanut oil for high oleate breeding program. A total of 329 peanut samples were used in this study, 227 of which were considered in the calibration equation development and 102 were utilized for validation, using near infrared reflectance spectroscopy (NIRS). The NIRS equations for all the seven fatty acids had low standard error of calibration (SEC) values, while high R2 values of 0.983 and 0.991 were obtained for oleic and linoleic acids, respectively in the calibration equation. Furthermore, the predicted means of the two main fatty acids in the calibration equation were very similar to the means based on gas chromatography (GC) analysis, ranging from 36.7 to 77.1% for oleic acid and 7.1 to 42.7% for linoleic acid. Based on the standard error of prediction (SEP), bias values, and $R^2$ statistics, the NIRS fatty acid equations were accurately predicted the concentrations of oleic and linoleic acids of the validation sample set. These results suggest that NIRS equations of oleic and linoleic acid can be used as a rapid mass screening method for fatty acid content analysis in peanut breeding program.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.10
• /
• pp.2995-3000
• /
• 2014

A sensitive concentration method utilising modified gas-purge microsyringe extraction (GP-MSE) was developed. Concentration (reduction in volume) to a microlitre volume was achieved. PAHs were utilised as semivolatile analytes to optimise the various parameters that affect the concentration efficiency. The injection rate and temperature were the key factors that affected the concentration efficiency. An efficient concentration (75.0-96.1%) of PAHs was obtained under the optimised conditions. The method exhibited good reproducibility (RSD values that ranged from 1.5 to 9.0%). The GP-MSE concentration method enhances the volume reduction (concentration factor), leading to a low method detection limit ($0.5-15ngL^{-1}$). Furthermore, this method offers the advantage of small-volume sampling, enabling even the detection of diurnal hourly changes in the concentration of PAHs in ambient air. Utilising this method in combination with GC-MS, the diurnal hourly flux of PAHs from the gas phase of ambient air was measured. Indeed, the proposed technique is a simple, fast, low-cost and environmentally friendly.

• Restorative Dentistry and Endodontics
• /
• v.38 no.4
• /
• pp.258-262
• /
• 2013

The restorative management of deep carious lesions and the preservation of pulp vitality of immature teeth present real challenges for dental practitioners. New tricalcium silicate cements are of interest in the treatment of such cases. This case describes the immediate management and the follow-up of an extensive carious lesion on an immature second right mandibular premolar. Following anesthesia and rubber dam isolation, the carious lesion was removed and a partial pulpotomy was performed. After obtaining hemostasis, the exposed pulp was covered with a tricalcium silicate cement (Biodentine, Septodont) and a glass ionomer cement (Fuji IX extra, GC Corp.) restoration was placed over the tricalcium silicate cement. A review appointment was arranged after seven days, where the tooth was asymptomatic with the patient reporting no pain during the intervening period. At both 3 and 6 mon follow up, it was noted that the tooth was vital, with normal responses to thermal tests. Radiographic examination of the tooth indicated dentin-bridge formation in the pulp chamber and the continuous root formation. This case report demonstrates a fast tissue response both at the pulpal and root dentin level. The use of tricalcium silicate cement should be considered as a conservative intervention in the treatment of symptomatic immature teeth.

• Publications of The Korean Astronomical Society
• /
• v.30 no.2
• /
• pp.255-259
• /
• 2015

Recent narrow-band Ca photometry discovered two distinct red giant branch (RGB) populations in some massive globular clusters (GCs) including M22, NGC 1851, and NGC 288. In order to investigate the differences in light/heavy elements abundances between the two subpopulations, we have performed low-resolution spectroscopy for stars on the two RGBs in these GCs. We find a significant difference (more than $4{\sigma}$) in calcium abundance from the spectroscopic HK' index for both M22 and NGC 1851. We also find a more than $8{\sigma}$ difference in CN band strength between the Ca-strong and Ca-weak subpopulations. For NGC 288, however, we detect the presence of a large difference only in the CN strength. The calcium abundances of the two subpopulations in this GC are identical within errors. We also find interesting differences in CN-CH relations among these GCs. While CN and CH indices are correlated in M22, they show an anti-correlation in NGC 288. However, NGC 1851 shows no difference in CH between two groups of stars having different CN strengths. The CN bimodality in these GCs could be explained by pollution from intermediate-mass asymptotic giant branch stars and/or fast-rotating massive stars. For the presence or absence of calcium bimodality and the differences in CN-CH relations, we suggest these would be best explained by how strongly type II supernovae enrichment has contributed to the chemical evolutions of these GCs.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1516-1516
• /
• 2001

During the recent years, wine analysis has played an increasing role due the health benefits of phenolic ingredients in red wine [1]. On the other hand there is the need to be able to distinguish between different wine varieties. Consumers want to know if a wine is an adulterated one or if it is based on the pure grape. Producers need to certificate their wines in order to ensure compliance with legal regulations. Up to now, the attempts to investigate the origin of wines were based on high-performance liquid chromatography (HPLC), gas chromatography (GC) and pyrolysis mass spectrometry (PMS) [l,2,3]. These methods need sample pretreatment, long analysis times and therefore lack of high sample throughput. In contradiction to these techniques using near infrared spectroscopy (NIRS), no sample pretreatment is necessary and the analysis time for one sample is only about 10 seconds. Hence, a near infrared spectroscopic method is presented that allows a fast classification of wine varieties in bottled red wines. For this, the spectra of 50 bottles of Cabernet Sauvignon, Lagrein and Sangiovese (Chianti) were recorded without any sample pretreatment over a wavelength range from 1000 to 2500 nm with a resolution of 12 cm$\^$-1/. 10 scans were used for an average spectrum. In order to yield best reproducibility, wines were thermostated at 23$^{\circ}C$ and a optical layer thickness of 3 mm was used. All recorded spectra were partitioned into a calibration and validation set (70% and 30%). Finally, a 3d scatter plot of the different investigated varieties allowed to distinguish between Cabernet Sauvignon, Lagrein and Sangiovese (Chianti). Considering the short analysis times this NRS-method will be an interesting tool for the quality control of wine verification and also for experienced sommeliers.

• Journal of Food Hygiene and Safety
• /
• v.15 no.2
• /
• pp.144-150
• /
• 2000

The present study was peformed to determine the hydrolysis rate constants and degradation products of phosphamidon and proffnofos by the OECD method. Hydrolysis rate constants of phosphamidon in pH 4, pH 7, and pH 9 buffer solutions at 25 and 40$^{\circ}$C were 0.0020, 0.0022, 0.0049 and 0.0040, 0.0050, 0.0150, respectively. Hydrolysis rate of phosphamidon was accelerated by temprerature change under same pH conditions, and half-life of phosphamidon in pH 9 at 40。C was 3 times faster than that at 25。C. Hydrolysis rate of phosphamidon in alkaline solution(pH 9) was 2~4 times faster than that in acidic solution(pH 4) and neutral solution(pH 7) under same temperature. Hydrolysis rate constants of profenofos in pH 4, pH 7, and pH 9 buffer solutions at 25 and 40。C were 0.0022, 0.0047, 0.0860 and 0.0035, 0.0086, 0.1245, respectively. Hydrolysis rate of profenofos was accelerated by temprerature change under same pH conditions. Hydrolysis rate of profenofos in alkaline solution(pH 9) was 15~40 times faster than in acidic solution(pH 4) and neutral solution(pH 7) under same temperature condition, and half-life of profenofos was very fast within 8 hours. The hydrolysis rate of profenofos was faster than that of phosphamidon. In order to identify hydrolysis products, the extracts of degradation products were analyzed by GC/MS. The mass spectra of hydrolysis products of phosphamidon were at m/z 153 and 149, those of the profenofos were at m/z 208 and 240, respectively. The hydrolysis products of phosphamidon were O, O-dimethyl phosphate(DMP) and N, N-diethylchloroacetamide, and those of profenofos were 4-bromo-2-chlorophenol and O-ethyl-S-propyl phosphate.