• Journal of the Korean GEO-environmental Society
• /
• v.22 no.3
• /
• pp.45-51
• /
• 2021

The evaluation of the degree of compaction of the embankment area, which accounts for most of highway earthworks, is generally performed by a flat plate loading test. The plate loading test is a traditional test method and has high reliability in the field. However, as reaction force equipment must be carried out and it takes about 40 minutes per site during the test, there may be limitations in managing the entire expanse of earthworks. Meanwhile, in order to overcome this, the Ministry of Land, Infrastructure and Transport proposed a simple method of evaluating the level of compactness in the provisional guidelines for compaction management of the packaging infrastructure in 2010. However, it has not been utilized at the highway construction site until now, 10 years later. Therefore, this study attempted to verify the utility of the compaction evaluation method using LFWD (Light Falling Weight Deflectometer) of the impact loading method among the test methods suggested in the provisional guideline. To this end, the correlation was derived by conducting a plate loading test and an LFWD test for each site property and compaction degree. As a result of the test, there was no consistency of test data in the ground with a relative compaction of 80% or less. However, it was confirmed that the correlation has a tendency to increase beyond that. If the test method or test equipment is improved to ensure the consistency of the test values of the impact loading method in the future, it will play a big role in solving the blind spot for compaction management in the earthworks.

• Journal of Bio-Environment Control
• /
• v.5 no.1
• /
• pp.23-33
• /
• 1996

This study was performed to induce a quality improvement and standardization of materials used for greenhouse. For this purpose, physical and mechanical properties of agricultural films for greenhouse were measured by kinds and thickness of the films. The properties are composed of impact, tensile, tear propagation strength and light transmittance. The results were summarized as follows. 1. At the impact test result of the falling dart, the thicker the film, the greater the impact strength of soft film. The impact weight at 50 percents is from 158g to 213g and the strength of low density polyethylene(LDPE) film is higher than the rest of any other films. 2. Seeing the leveling of the impact rupture, maximum impact weight which was ruptured very little ranges from 62g to 192g. The impact strength of 0.1mm films was higher than that of 0.05mm as from 1.8 to 3.2 times. 3. Tensile weight covers from 0.95kg to 2.22kg in the test materials, and the weight of lengthwise film is larger than that of width. LDPE film has high value of tensile weight. Elongation range is from 345 to 102 percent and lengthwise elongation is greater than width as much as from 1.4 to 2.7 times. 4. Tea. propagation strength ranges from 80.5kg/cm to 121.7kg/cm, and unlike which of LDPE film has high value, EVA film has low value in the films tested. The width strength is higher than the lengthwise. 5. The light transmittance of the soft film is about 78-92 percent in the range of ultraviolet ray, but has high value in the visible ray range.

• Journal of Navigation and Port Research
• /
• v.39 no.1
• /
• pp.77-82
• /
• 2015

Slamming means that the hull hits the waves and receives impact pressure. This slamming effect may cause harm to people and when you put the hull at risk. so it is very harmful for cargo safety. Therefor slamming impact pressure should be fully considered in ship designing. In this study the model of wedged type structure are produced aimed to simulate a free fall that the experiments were carried out on different weight and free fall height. The flow field has been obtained by 2-frame grey level cross correlation PIV(Particle Image Velocimetry) method and experiment was divided into water entry and water exit. The impact pressure of free fall structure by a pressure acquisition system apply to dewetron system. The angles between a model and the water surface are adapted $15^{\circ}$ respectively. The weight change of models was given as 1.5, 1.8 and 2.0kg. To study slamming phenomenon for free fall height the experiments were carried out by the free fall height of 100, 200 and 300mm. The experimental value of the impact pressure according to the changes in weight was increase impact pressure in proportion to the increase in weight and higher free falling height has also influenced the increase in impact pressures.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.636-643
• /
• 2008

The objective of this paper is to assess the potential use of the geogauge and the light falling weight deflectometer (LFWD) and the soil impact hammer as quality control/quality assurance $Q_C/Q_A$ devices for compacted soil layers. A comprehensive field experimental program considering variation of number of compaction, water contents and thickness of compaction layer was conducted on compacted layers of gravel sand. The geogauge, LFWD, the soil impact hammer and static load test (PLT) as a reference test were performed for the compacted layers. The geogauge elastic modulus, $E_G$, the LFWD dynamic modulus, ELFWD, empirical soil stiffness, $K_{30}$, obtained from soil impact hammer and soil stiffness directly obtained from PLT, $K_{30}$, were correlated with increasing number of compaction. The results of this study show that the geogauge, LFWD and the soil impact hammer, which are very simple to test, can be used as substituting devices for static PLT which is a conventional quality control/quality assurance $Q_C/Q_A$ devices for compacted soil layers.

• Textile Coloration and Finishing
• /
• v.34 no.3
• /
• pp.173-184
• /
• 2022

In this study, the TPU film was laminated on an aramid fabric or circular knits in order to implement an air cushion material that can respond to high impact forces in case of a fall and is easy to expand. To increase the bonding strength between the fabric layer and the film layer, a primer layer was formed in two ways: one for thermally bonding and laminating PET film and two for coating and aging hot melt type PUR adhesive. The tensile strength of the aramid air cushion was 2.5 times higher than that of the circular knits, but the tensile elongation of the aramid air cushion was very low compared to that of the circular knits. The tear strength of the aramid air cushion was about twice or more superior to that of the circular knits, the primer treatment method was good at A, and the peel strength was excellent at method A. The aramid air cushion was the lightest in weight. Summarizing the above results, it was best to combine the air cushion material with aramid woven fabric and primer treatment method A to cope with the high impact force applied when falling.

• Explosives and Blasting
• /
• v.26 no.1
• /
• pp.15-21
• /
• 2008

In case of estimating the shocking vibration during the blasting demolitions, the weight and falling height of the structure, that is a potential energy, had been considered. But, this study presented a new equation which used the impulse concerning a falling weight instead of potential energy as a method of predicting the shock vibration. In this experiment, the data of the impulse were compared with the data of the potential energy by performing the free-fall, and all data were comparatively analyzed by the regression analysis method. Also, the method of the superposition theory, which is calculated by the diminution ratio according to distance, the free-fall difference according to height, and the time giving the shock to the ground according to the breakdown pattern, was compared with the previous vibration data occurring from the blasting demolitions in the same conditions. As a result, this study suggests that the impulse and the method of superposition theory be applied as a method of predicting the shocking vibration. Therefore, these results could be expected to estimate the shocking vibration more accurately than the previous method.

• Journal of Mechanical Science and Technology
• /
• v.15 no.7
• /
• pp.1072-1076
• /
• 2001

A biomechanical study was conducted in this study to investigate if in-line skating wrist guards can effectively reduce the impact forces so as to protect the wrist from fracture. The forearm specimens with and without wrist guards were dropped using a specially designed sled to simulate the impact on the wrist while falling. A force plate was used to measure the total impact force on the dropping weight whereas a load cell was attached to the proximal end of the specimen and used to quantify the impact transmitted through the wrist joint. From the non-destructive tests, mean peak force measured from a force plate showed no difference between the guarded and unguarded groups whereas mean impulse of the guarded group was significantly greater than that of the unguarded group (p<0.01). Comparing the peak force and impulse measured from the load cell, the peak force of the guarded group was significantly less than that of the unguarded group (p<0.001), while the impulse values were similar. When the specimens were dropped from a higher position (2.5ft ve. 1ft), all unguarded specimens had severe wrist fractures whereas fracture was found in three out of 5 guarded specimens. Comparison of mean peak forces and impulses showed as significant difference between the guarded and unguarded groups only in the mean impulse measured from the force plate. These results suggest that the wrist guard may protect the wrist by attenuating the peak force transmitted to radius and ulnar although it may not be effective when the wrist is subjected to an impact sufficiently large to cause fractures.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.1
• /
• pp.51-65
• /
• 2019

A wood-plastic composite (WPC) paver block was manufactured using wood chips waste through an extrusion process, and it was intended to be used for paving in basic rest areas. The first stage in this study covered preliminary tests in terms of flexural strength and dimensional swelling to determine the optimal WPC compounding mix condition, by variation of the WPC ingredients. Next, three different paver blocks including the WPC block, a non-porous cement block, and a porous cement block were tested in terms of various material properties in the laboratory. Finally, two outdoor test sections of the proposed paver blocks were prepared to simulate a basic rest area. Test results indicated that the flexural strength of the WPC paver blocks was about 1.6 times greater than that of the tested cement paver blocks. The WPC block pavement was unaffected by water buoyance as well as volume expansion due to swelling. Results from the impact absorbance test and light falling weight deflectometer (LFWD) test clearly showed that the WPC block paving system marginally satisfied the comfortable and safe hardness range from the pedestrians' perspective, while the results demonstrated that it is structurally sound for application as a road paving block.

• Nuclear Engineering and Technology
• /
• v.26 no.2
• /
• pp.197-204
• /
• 1994

In a PWR rod cluster control assembly(RCCA) for shutdown is released upon action of control rod drive mechanism and falls down through the guide thimble by its weight. Drop time and impact velocity of the RCCA are two key parameters with respect to reactivity insertion time and the mechanical integrity of fuel assembly. Therefore, the precise control of drop time and impact velocity is prerequisite to modifying the existing design features of the RCCA and guide thimble or newly designing them. During its falling down into the core, the RCCA is retarded by various forces acting on it such as fluid resistance caused by the RCCA movement, buoyance and mechanical friction caused by contacting inner surface of the guide thimble, etc. However, complicated coupling of the various forces makes it difficult to derive an analytical dynamic equation for the drop time and impact velocity. This paper deals with the development of a computer program containing an analytical dynamic equation applicable to the Korean Fuel Assembly(KOFA). The computer program is benchmarked with an available single control rod drop tests. Since the predicted values are in good agreement with the test results, the computer program developed in this paper can be employed to modify the exiting design features of the RCCA and guide thimble and to develope their new design features for advanced nuclear reactors.

• Advances in concrete construction
• /
• v.13 no.6
• /
• pp.433-450
• /
• 2022

The conventional disposal methods of waste tires are harmful to the environment. Moreover, the recycling/reuse of waste tires in domestic and industrial applications is limited due to parent product's quality control and environmental concerns. Additionally, the recycling industry often prefers powdered rubber particles (<0.60 mm). However, the processing of waste tires yields both powdered and coarser (>0.60 mm) size fractions. Reprocessing of coarser rubber requires higher energy increasing the product cost. Therefore, the waste tire rubber (WTR) less favored by the recycling industry is encouraged for use in construction products as one of the environment-friendly disposal methods. In this study, WTR fiber >0.60 mm size fraction is collected from the industry and sorted into 0.60-1.18, 1.18-2.36-, and 2.36-4.75-mm sizes. The effects of different fiber size fractions are studied by incorporating it as fine aggregates at 10%, 20%, and 30% in the self-compacting rubberized concrete (SCRC). The experimental investigations are carried out by performing fresh and hardened state tests. As the fresh state tests, the slump-flow, T500, V-funnel, and L-box are performed. As the hardened state tests, the scanning electron microscope, compressive strength, flexural strength and split tensile strength tests are conducted. Also, the water absorption, porosity, and ultrasonic pulse velocity tests are performed to measure durability. Furthermore, SCRC's energy absorption capacity is evaluated using the falling weight impact test. The statistical significance of content and size fraction of WTR fiber on SCRC is evaluated using the analysis of variance (ANOVA). As the general conclusion, implementation of various size fraction WTR fiber as fine aggregate showed potential for producing concrete for construction applications. Thus, use of WTR fiber in concrete is suggested for safe, and feasible waste tire disposal.