• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.3
• /
• pp.95-108
• /
• 1993

The needs for smooth curves and surfaces are increasing in modeling cars, ships, airplanes, and other consumer products either for aesthetic or functional purpose. However, the curves and surfaces generated by conventional modeling methods usually exhibit an unwanted behavior due to digitizing errors or inadequate generation method, and thus much time and extra effort is spent afterwards to get the faired results. The objective of this work is to develop a fairing scheme by which well refined shape of a surface can be acquired with detecting and removing the shape imperfections of the given surface represented by NURBS. The fairing scheme is based on an optimization process in which the control points of the given surface are repositioned to minimize the integration of the jumps(perturbations) of the unit normal vectors at all surface points.

• Proceeding of EDISON Challenge
• /
• 2016.11a
• /
• pp.90-95
• /
• 2016

본 연구에서는 교육 및 연구를 위한 CFD 해석 프로그램인 EDISON_CFD 프로그램을 이용하여 화물 트럭의 후면부 형상변화에 따른 공력특성을 분석해보았다. 먼저 추가적인 부착물을 장착하지 않은 기본적인 형상의 화물트럭의 공력특성을 확인 후, 후면부에 여러 형상의 Boat tail(보트 테일)과 전면부에 Cap-roof fairing(캡루프 페어링)이 부착된 형상을 해석하여 트럭이 받는 항력 감소를 통해 최적형상을 찾아가는 연구를 수행하였다. Cap-roof fairing이 부착된 형상에서 $15^{\circ}$의 특성길이가 0.3인 Boat tail에서 가장 좋은 항력 감소 효과를 얻을 수 있었다. Cap-roof fairing의 경우 6%의 항력 계수 감소를 보였고, Boat tail에서 20%의 항력 계수 감소효과를 관찰할 수 있었다. Boat tail의 각도와 길이를 변수로 하여 여러 해석을 진행한 결과 최적화된 형상을 선정할 수 있었다.

• Advances in aircraft and spacecraft science
• /
• v.7 no.4
• /
• pp.371-385
• /
• 2020

A forward-facing aerospike attached to a payload fairing of a satellite launch vehicle significantly alters its flowfield and decreases the aerodynamic drag in transonic and low supersonic speeds. The present payload fairing is an axisymmetric configuration and consists of a blunt-nosed body along with a conical section, payload shroud, boat tail and followed by a booster. The main purpose of the present numerical simulations is to evaluate flowfield and assess the performance of aerodynamic drag coefficient with and without aerospike attached to a payload fairing of a typical satellite launch vehicle in freestream Mach number range 0.8 ≤ M_∞ ≤ 3.0 and freestream Reynolds number range 33.35 × 10⁶/m ≤ Re_∞ ≤ 46.75 × 10⁶/m whichincludes the maximum aerodynamic drag and maximum dynamic conditions during ascent flight trajectory of the satellite launch vehicle. A numerical simulation has been carried out to solve time-dependent compressible turbulent axisymmetric Reynolds-averaged Navier-Stokes equations. The closure of the system of equations is achieved using the Baldwin-Lomax turbulence model. The aerodynamic drag reduction mechanism is analysed employing numerical results such as velocity vector plots, density and Mach contours in conjunction with the experimental flow visualization pictures. The variations of wall pressure coefficient over the payload fairing with and without aerospike are exhibiting different kind of flowfield characteristics in the transonic and low supersonic speeds. The numerically computed results are compared with schlieren pictures, oil flow patterns and measured wall pressure distributions and exhibit good agreement between them.

• 한국전산유체공학회:학술대회논문집
• /
• 2006.05a
• /
• pp.90-93
• /
• 2006

• Aerospace Engineering and Technology
• /
• v.2 no.1
• /
• pp.171-181
• /
• 2003

The nose fairings of KSR-III are designed to be separated from the rocket by explosive force at the mission altitude to expose the payload. Adequate amount of separation force should be imposed to allow safe separation without collision between the fairings and the rocket, and the separation device was designed for the separation at very high altitude where almost no air load was expected. As the development of KSR-III goes on, several design changes have made and lower separation altitude of 45km is expected as a result. Under these circumstances, it is required to determine if the nose fairings can be separated without collision with much severer air load than for the design condition. In this study, the 6-DOF motion analysis program, PASEM, which was developed to predict the strap-on booster separation, is modified to simulate the pivotal motion of the fairings at early stages of separation. The accuracy of pivot motion simulation is validated by comparison with the results of ground test and the accurate separation conditions are deduced from it. Trajectory simulations are performed to see if separation without collision is possible with varying angle of attack, direction of gravity, and the effect of gust. It is also found that reducing the separation angle of the clamshell hinge from 60 degrees to 40 degrees can enhance separation safety and separation at lower altitude of 40km can be done without collision.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.6
• /
• pp.76-82
• /
• 2005

Cable fairings of guided missiles are generally used for protection of electric cables under aerodynamic heating and mechanical loading. The stress distributions between a cable fairing and missile main body along a cable fairing are necessary for its design. In this paper, a method for bonding stress and strength analysis of a cable fairing has been investigated and its computer program developed. Tensile and three-point bending tests of generally used bonding materials were also conducted to supply basic material properties for design of cable fairings.

• Journal of Korean Institute of Industrial Engineers
• /
• v.27 no.1
• /
• pp.1-10
• /
• 2001

In the reverse engineering, surfaces are modeled for new products by interpolating the digitized data points obtained by measuring the existing shapes. However, many measuring or deviation errors are happened during the measuring process. If these errors are ignored, designers could get undesirable results. Therefore, it is important to handle such errors and fairing procedure with the esthetics criteria is needed during surface modeling process. This paper presents algorithms for the fairing of B-spline surfaces. The algorithms are based on automatic repositioning of control points for B-spline surfaces. New positions of the control points are determined by solving a non-linear programming of which the objective functions are derived variously using derived surfaces and constraints are established by distance measures between the original and the modified control points. Changes in surface shapes are analyzed by illustrations of their shapes and continuous plotting of gaussian and mean curvatures.

• Aerospace Engineering and Technology
• /
• v.3 no.2
• /
• pp.42-49
• /
• 2004

Analytical solutions are developed to predict temperature of a satellite box during launch stage under the assumption of worst hot condition. The considered time period is from fairing jettison to separation of satellite during launch stage. After fairing jettison, a box mounted on outer surface of satellite are exposed to space environments such as direct solar flux, Earth IR, Albedo, and free molecular heating. The thermal governing equation is simplified to 1st order ordinary differential equation such that analytic solutions are acquired after the box is assumed as a single lumped mass. The analytical solutions are also available for mass varying box. Finally, the practical application is performed for the case of STSAT-1 launch scenario.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.10
• /
• pp.753-763
• /
• 2020

A wind tunnel test of 29.7% scaled model of NASA Common Research Model with belly model support was performed in small low speed wind tunnel. The static aerodynamic forces and moments of CRM were measured with belly sting support configuration. Pitching moments of belly sting with various fairings were compared and small interference fairing shape was found. The belly sting model support interference and reducing effect of fairing shapes with CFD analysis.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.194-201
• /
• 2006

Roof-fairing and deflector system have been used on heavy-duty trucks to minimize aerodynamic drag force not only for driving stability of the truck but also for energy saving by reducing the required driving power of the vehicle. In this study, a numerical simulation was carried out to see aerodynamic effect of the drag reducing device on the model vehicle. Drag and lift force generated on the five different models of the drag reducing system were calculated and compared them each other to see which type of device is efficient on the reduction of driving power of the vehicles quantitatively. An experiment has been done to see airflow characteristics on the model vehicles. Airflow patterns around the model vehicles were visualized by smoke generation method to compare the complexity of airflow around drag reducing device. From the results, the deflector systems(Model 5,6) were revealed as a better device for reduction of aerodynamic drag than the roof-fairing systems(Model 2,3,4) on the heavy-duty truck and it can be expected that over 10% of brake power of an engine can be saved on a tractor-trailer by the aerodynamic drag reducing device at normal speed range($80km/h{\sim}$).