• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.3
• /
• pp.579-587
• /
• 1998

In this study, fatigue behavior of the optical fiber sensor embedded in composite laminate was investigated. Static tensile and fatigue tests were performed for three types of laminated composite specimens with embedded optical fiber sensor in the neutral plane ; [0/sub 6//OF/0/sub 6/]/sub T/, [0/sub 2//90/sub 4//OF/90/sub 4//0/sub 2/]/sub T/ and [0/sub 3//90/sub 3//OF/90/sub 3//0/sub 3/]/sub T/. The fracture of the embedded optical fiber sensor was detected by the intensity drop off of laser signal transmitted through the optical fiber sensors embedded within laminated composite specimen. The maximum fatigue stress applied to laminated specimen was compared with the average tensile stress at which the fracture of the embedded optical fiber within the laminate occurred under static tensile loading. From the experiments, firstly it is observed that the decrease in the life of optical fiber sensors embedded within unidirectional-ply laminate by the fatigue loading is relatively small compared to that of cross-ply laminate. Secondly, the optical fiber embedded in unidirectional-ply laminate is fractured by the fatigue damage due to the growth of internal defects of optical fiber, however the optical fiber embedded in cross-ply laminate is fractured by the growth of transverse matrix crack.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.25 no.4
• /
• pp.375-378
• /
• 1999

Incidence and mortality rate of maxillofacial infection is relatively low in the era of antibiotics. Despite the use of antibiotics, delayed treatment, underlying systemic diseases, drug-resistant microorganisms may result in life-threatening situations. The deep neck infection developed from odontogenic infection may result in sepsis, mediastinitis, aspiration pneumonia, asphyxia. Sepsis is the most dangerous complication which can quickly result in a number of lethal situations. The treatment of sepsis includes awareness of such complication, use of sensitive antibiotics, removal of infection source, and hemodynamic, respiratory and metabolic support. We experienced a patient who died of sepsis, which developed from odontogenic infection. The initial diagnosis was a buccal space cellulitis. However, in spite of medical and surgical treatment, this progressed to Ludwig's angina and then deep neck infection and finally sepsis. On the 10th hospital day, the patient died of multiorgan failure caused by sepsis.

• Asian-Australasian Journal of Animal Sciences
• /
• v.24 no.7
• /
• pp.912-918
• /
• 2011

Newly born lambs have to face challenges in a new environment totally different from that of the uterus. Adaptation to extra-uterine life involves functional changes with almost each organ and system in the body undergoing a series of metabolic and anatomical modifications. Failure to adapt the extra-uterine environment can not only lead to homeostatic disturbances but also lead to the death of the affected lambs. Hematological parameters of newly born lambs show variability that differs between breeds of lambs. The purpose of present study was to determine homeostatic responses and physiological reference values in Kajli breed lambs occurring in the neonatal period through changes in blood profile, respiratory rate, heart rate, live weight and rectal, scrotal and skin temperatures. For this purpose, sixteen clinically fit lambs (males = 10 and females = 6) with a mean body weight $6.92{\pm}0.46$ kg were selected. Physiological data of selected parameters of each Kajli lamb was recorded at three day intervals and hematological parameters at five days for a period of 30 days. In general, statistical analysis showed a significant effect of time (p<0.001) on all the studied physiological and hematological parameters except platelets counts, white blood cells and hemoglobin concentration. The results documented in the current study are an addition to existing knowledge of the physiology of Kajli sheep breed should be helpful in developing feeding, disease diagnoses and treatment protocols for newborn Kajli stock.

• Journal of Korean Society of Forest Science
• /
• v.105 no.4
• /
• pp.449-455
• /
• 2016

This study was conducted to provide the basic policy information for systematic forest road planning and maintenance management by surveying two different administrator groups. The survey results showed that the high priorities of forest road planning were silviculture, disaster prevention, and timber harvesting, and main forest road type was preferred for future use. Also 92.9% of the respondents expressed difficulties due to insufficient manpower and budget. The expected damage types due to forest road construction were threat-to-life by slope failure and dispute on crossing private land. The current main maintenance tasks on forest roads included drainage and road surface maintenance works. Main forest road facilities that should be needed after the construction were installation of additional drainage structures, and slope revegetation and stabilization.

• Journal of the Korean School Mathematics Society
• /
• v.10 no.3
• /
• pp.303-322
• /
• 2007

This study is to investigate student's processes of problem solving using open-ended Geometric problems to understand student's thinking and behavior. One 8th grader participated in performing her learning in 5 lessons for June in 2006. The result of the study was documented according to Polya's four problem solving stages as follows: First, the student tended to neglect the stage of "understanding" a problem in the beginning. However, the student was observed to make it simplify and relate to what she had teamed previously Second, "devising a plan" was not simply done. She attempted to solve the open-ended problems with more various ways and became to have the metacognitive knowledge, leading her to think back and correct her errors of solving a problem. Third, in process of "carrying out" the plan she controled her solving a problem to become a better solver based on failure of solving a problem. Fourth, she recognized the necessity of "looking back" stage through the open ended problems which led her to apply and generalize mathematical problems to the real life. In conclusion, it was found that the student enjoyed her solving with enthusiasm, building mathematical belief systems with challenging spirit and developing mathematical power.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.5 s.236
• /
• pp.663-670
• /
• 2005

DIN CK35 (JIS S35CK) steels have been used as a material in fuel pump blocks for marine engines. Failures in the inner surface of a drilling hole, due to the initiation of fatigue cracks have been frequently reported. However, the mechanism initiating these cracks and growths has not been clearly diagnosed yet. This study was conducted using a scraped fuel pump block, containing an initiated fatigue crack in the inner surface of a drilling hole. Initially, the cracks and fractured surfaces inside the block were investigated using an optical microscope and a SEM (Scanning Electron Microscope). In addition, microstructure observation, fatigue life test and fatigue crack growth test were performed using a specimen, which was taken from the same block. Results from these tests are summarized as follows; (1) The early crack in the block was supposed to occur inside the inner surface of the drilling hole. (2) The fatigue endurance of this material was about 330 Mpa. (3) The early crack was generated in the cavitations created by the breakdown of a big inclusion, or separation between the big inclusion and the base metal, in which the fundamental ingredients of the inclusion were C, 5, and Mn. (4) In order to prevent these types of failures, the suppression of inclusions inflow by improving the casting process, formation of fine inclusions by applying a heat treatment process, and coating of the surface of the drilling hole were required.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.2
• /
• pp.137-143
• /
• 2016

The fifth wheel coupler is a heavy automotive coupling structure which connects a tractor and a trailer used for heavy-duty trucks widely. It is subjected to various loads simultaneously such as rolling, pitching and yawing loads as well as coupling frictional and impact loadings. Most of existing couplers have been overdesigned and, therefore, it is necessary to reduce the dead weight to increase the fuel efficiency. The topology optimization was applied in order to find conceptual layout designs which could show major load paths and ribs locations, and then the size structural optimization was performed in order to determine the heights and thicknesses of coupler ribs with the predetermined various loading conditions for the development of a new slim coupler with a minimum weight and high enough strength and stiffness. As the results of the topology optimum design, an efficient new coupling structure for truck trailers was designed. The weight of the new fifth wheel coupler was reduced by 4.9 %, compared with the existing one, even though all strength requirements were satisfied. The fatigue test of the new coupler was performed with cyclic vertical loads (+78.4 to +235.2 kN) and horizontal loads (-91.2 to +91.2 kN) simultaneously at 1 Hz and the life of 2,000,000 cycles were achieved without failure.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.6
• /
• pp.537-546
• /
• 2010

This research work contributed to a study for the procedure and methodology to assess the fatigue durability for a composite torque link of helicopter landing gear, which was newly developed and fabricated by the resin transfer moulding technique to interchange with metal component. The simulated load spectrum anticipated to be applied to the torque link during its operation life was generated using an advanced method of probabilistic random process, and the fatigue durability was evaluated by the strength degradation approach on the basis of material test data. The full scale fatigue test was also performed and compared with the analysis results.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.1
• /
• pp.59-65
• /
• 2012

Plant growth-promoting effects of rhizobacterial inoculation obtained in pot experiments cannot always be dependably reproduced in fields. In this study, we investigated the effect of inoculation with Azospirillum brasilense and Methylobacterium oryzae, which have displayed growth promoting effects in several pot experiments, on growth and fruit yield of red pepper under field condition in a plastic-film house. Four rows spaced 90 cm apart were prepared after application of compost ($10Mg\;ha^{-1}$), and red pepper seedlings (Capsicum annum L., Nocgwang) were transplanted in each row with 40-cm space. Experimental treatments were consisted of A. brasilense CW903 inoculation, M. oryzae CBMB20 inoculation, and uninoculated control. Twelve plots, 10 plants per plot, were allotted to the three treatments with four replicates in a completely randomized design. At the time of transplanting, 50 mL of each inoculum ($1{\times}10^8cells\;mL^{-1}$) was introduced into root zone soil of each plant, and re-inoculated at 7 and 14 days after transplant. Plant growth and fruit yield were measured during the experiment. Both A. brasilense CW903 and M. oryzae CBMB20 could not promote growth of red pepper plants. All growth parameters measured were not significantly different among treatments. There were large variations in fruit yield recorded on plot basis, and no statistically significant differences were found among treatments. The failure to demonstrate the expected plant growth promoting effect of the inoculants is possibly due to various environmental factors, including weather and soil characteristics, reducing the possibility to express the potential of the inoculated bacterial strains.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1172-1175
• /
• 2004

At present, CHS(Compression Hip Screw) is one of the best prosthesis for the intertrochanteric fracture. There is nothing to evaluate the CHS itself with the finite element analysis and mechanical tests. They have same ways of the experimental test of the ASTM standards. The purpose of this study is to evaluate the existing CHS and the new CHS which have transformational design factors with finite element analysis and mechanical tests. The mechanical tests are divided into compression tests and fatigue test for evaluating the failure load, strength and fatigue life. This finite element method is same as the experimental test of the ASTM standards. Under 300N of compression load at the lag screw head. There are less differences between Group (5H, basic type) and Group which has 8 screw holes. However, there are lots of big differences between Group and Group which is reinforced about thickness of the neck range. Moreover, the comparison of Group and Group shows similar tendency of the comparison of Group and Group . The Group is reinforced the neck range from Group. After the experimental tests and the finite element analysis, the most effective design factor of the compression hip screws is the reinforcement of the thickness, even though, there are lots of design factors. Moreover, to unite the lag screw with the plate and to analyze by static analysis, the result of this method can be used with experimental test or instead of it.