• 한국터널지하공간학회 논문집
• /
• 제7권3호
• /
• pp.197-207
• /
• 2005

지하공간의 설계는 막장파괴와 관련한 안정성에 대한 평가를 필요로 한다. 막장파괴모드는 전통적인 안정성 평가법에서 중요하게 다루어져 왔다. 본 연구에서는 점착력이 없는 토사지반에 대한 모형실험을 실시하여 토피고와 지반경사의 변화에 따른 터널막장의 종방향 파괴모드를 파악하고자 하였다. 모형실험은, 대형지하공간의 폭원이 충분히 크다는 가정 하에 평면변형조건의 터널 축방향 굴착면 모델에 대하여 실시되었다. 실험결과 토피고와 지반경사는 파괴모드에 중요한 영형을 미치는 것으로 나타났다. 토피고가 증가할수록 지반의 파괴영역이 감소하여 국부 전단 파괴의 형태를 보였다. 또, 지반경사가 증가할수록 굴착면과 사면방향으로 확대되는 유형의 파괴모드를 확인할 수 있었다. 실험모델을 수치해석 모델로 재현하는 해석을 실시하였고, 이로부터 수치해석법을 통해서도 굴착면의 파괴모드의 추정이 가능함을 보였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.115-120
• /
• 2008

In this study, effects of surface roughness on adhesive strength of heat-resistant adhesive RTV88 were examined. Sandblast was used to generate rough surfaces on aluminum adherends, and then tensile-shear tests of Al/RTV88 single lap joints were performed. The shear strength was shown to be affected by the surface roughness. Effective area, peel failure area, and cohesive failure area were introduced to explain the effects of surface roughness on the adhesive strength. An empirical relation for the failure force was proposed based on these parameters and verified by the test results.

• 한국지반환경공학회 논문집
• /
• 제17권5호
• /
• pp.5-16
• /
• 2016

A rainfall induced slope failure is a common natural hazard in mountainous areas worldwide. Sudden and rapid failures which have a high possibility of occurrence in a steep slope are always the most dangerous due to their suddenness and high velocities. Based on a series of experiments this study aimed to determine a critical angle which could be considered as an approximate threshold for a sudden failure. The experiments were performed using 0.42 mm mean grain size sand in a 200 cm long, 60 cm wide and 50 cm deep rectangular flume. A numerical model was created by integrating a 2D seepage flow model and a 2D slope stability analysis model to predict the failure surface and the time of occurrence. The results showed that, the failure mode for the entire material will be sudden for slopes greater than $67^{\circ}$; in contrast the failure mode becomes retrogressive. There is no clear link between the degree of saturation and the mode of failure. The simulation results in considering matric suction showed good matching with the results obtained from experiment. A subsequent discarding of the matric suction effect in calculating safety factors will result in a deeper predicted failure surface and an incorrect predicted time of occurrence.

• Geomechanics and Engineering
• /
• 제18권3호
• /
• pp.247-258
• /
• 2019

Soil strength and failure surface geometry directly influence magnitudes of passive earth thrust acting on geotechnical retaining structures. Accordingly, it is expected that as long as the shape of the failure surface geometry and strength parameters of the backfill are known, magnitudes of computed passive earth thrusts should be highly accurate. Building on this premise, this study adopts conventional method of slices for calculating passive earth thrust and combines it with equations for estimating failure surface geometries based on in-situ stress state and density. Accuracy of the proposed method is checked using the results obtained from small-scale physical retaining wall model tests. In these model tests, backfill was prepared using either air pluviation or compaction and different backfill relative densities were used in each test. When the calculated passive earth thrust magnitudes were compared with the measured values, it was noticed that the results were highly compatible for the tests with pluviated backfills. On the other hand, calculated thrust magnitudes significantly underestimated the measured thrust magnitudes for those tests with compacted backfills. Based on this observation, a new approach for the calculation of passive earth pressures is developed. The proposed approach calculates the magnitude and considers the influence of locked-in stresses that are the by-products of the backfill preparation method in the computation of lateral earth forces. Finally, recommendations are given for any geotechnical application involving the compaction of granular bodies that are equally applicable to physical modelling studies and field construction problems.

• 한국안전학회지
• /
• 제21권6호
• /
• pp.74-81
• /
• 2006

Probabilistic Risk Assessment considering statistically random variables is performed for the preliminary design of a Arch Bridge. Component reliabilities of girders have been evaluated using the response surfaces of the design variables at the selected critical sections based on the maximum shear and negative moment locations. Response Surface Method(RSM) is successfully applied for reliability analyses for this relatively small probability of failure of the complex structure, which is hard to be obtained by Monte-Carlo Simulations or by First Order Second Moment Method that can not easily calculate the derivative terms of implicit limit state functions. For the analysis of system reliability, parallel resistance system composed of girders is changed into parallel series connection system. The upper and lower probabilities of failure for the structural system have been evaluated and compared with the suggested prediction method for the combination of failure modes. The suggested prediction method for the combination of failure modes reveals the unexpected combinations of element failures in significantly reduced time and efforts compared with the previous permutation method or system reliability analysis method.

• 대한토목학회논문집
• /
• 제8권3호
• /
• pp.85-90
• /
• 1988

균질토 사면에서 파괴에 대한 확률론적모델이 제시되었다. 사면의 안전은 관례적인 안전을 보다는 파괴확률로써 측정된다. 사면파괴의 Safety Margin은 정규분포라 가정하였다. 어떤 균질한 흙층에 있어서 흙의 특성에 영향을 주는 불확실성의 원인은 본래의 공간적인 가변성, 불충분한 시료에서 오는 판단오차 그리고 실험오차등이 었다. 파괴면을 따라 존재하는 전단강도의 불확실성은 1차원 Random Field Madels로 표현되었다. 파괴aus의 양상은 대수나선 곡선을 따른다고 가정하였다. 파괴면과 그것을 따라 작용하는 힘의 통계적 특성을 유도하여 사면의 파괴확률을 계산하였다. 마지막으로 개발된 절차가 사면의 신뢰성 해석에 대한 하나의 예제 연구에 적용되었다.

• 한국농공학회지
• /
• 제38권6호
• /
• pp.64-73
• /
• 1996

The three-dimensional strength behavior of compacted decomposed granite soil was studied using cubical triaxial tests with independent control of the three principal stresses. All specimens were loaded under conditions of principal stress direction fixed and aligned with the directions of compacted plane. For comparable test conditions, the major principal strain and volume strain to failure were smallest when the major principal stress acted perpendicular to the compacted plane. The opposite extremes were obtained when the major principal stress acted parallel to the compacted plane. In cubical triaxial tests with same b values and with ${\theta}$ values in one of three sectors of the octahedral plane, independent of the range of ${\theta}$, higher friction angles are obtained in tests with b greater than in triaxial compression tests in which b 0.0, Comparison between the results of the drained cubical triaxial tests on lksan compacted decomposed granite soil and the cross section of the Mohr-Coulomb failure surface as well as the cross section of the Mohr-Coulomb failure surface were made. Lade's isotropic failure criterion based on vertical specimens overestimates the strengths for tests performed with values of 0 between 90˚ and 1 50˚ the Mohr-Coulomb criterion generally underestimates the strengths of tests performed with values of ${\theta}$ between $0^{\circ}$ and $180^{\circ}$ except around the $120^{\circ}$.

• Geomechanics and Engineering
• /
• 제6권5호
• /
• pp.469-485
• /
• 2014

A series of bearing capacity tests was conducted with eccentrically loaded model surface and shallow strip footings resting close to a slope to investigate behavior of such footings (ultimate loads, failure surfaces, load-displacement curves, rotation of footing, etc.). Ultimate loads of footing close to slope decreased with increasing eccentricity for both surface and shallow footings. Failure surfaces were not symmetrical, primary failure surfaces occurred on the eccentricity side (the slope side) and secondary failure surfaces occurred on the other side. Lengths of failure surfaces decreased with increasing eccentricity. Footings always rotated towards eccentricity side a few degrees. For eccentrically loaded footing, decrease in ultimate load with increasing eccentricity is roughly in agreement with Customary Analysis.

• 한국생산제조학회지
• /
• 제5권3호
• /
• pp.73-79
• /
• 1996

In this paper present a new technique (strain-telemetering)for detection of coated tool failure in face milling processes. In the cutter body the strain signals received fro the transmitter is transformed in to frequency modulation(FM) signals in face milling processes. A receiver which is place near by the Vertical milling machine receives the FM signals, then the signals will be sent to a computer which determines whether th tool is failure. And machined surface of workpiece is detected by the SEM. In this paper, A on-line monitoring of the tool failure detection system based on the strain -telemetering apparatus has bee represented.

• 열처리공학회지
• /
• 제27권4호
• /
• pp.191-201
• /
• 2014

The gear was made of SNC815 case-carburized, quench hardened and tempered steel. The gears were failed far earlier than the expected service life used in the industrial site. Causes of the failed gear were analyzed by microstructure observation. By the SEM and micro structure examinations, the damaged surfaces had been weared and failed by fatigue. Through microscope observation on the damaged surface, it was found that the cause of failure was determined by external overloading and the initial stage of the damage was closely related to complex contact fatigue failure. The overload and contact fatigue contributed to the early failure cause.