• 멤브레인
• /
• 제21권2호
• /
• pp.127-140
• /
• 2011

본 연구에서는 정수처리용 세라믹 한외여과 및 광촉매의 혼성공정에서 $TiO_2$ 광촉매 코팅 구(bead)의 농도 및 물역세척 주기(FT), 물역세척 시간(BT) 변화의 영향을 알아보았다. 광촉매 코팅 구의 농도는 10~40 g/L로, FT는 2~10분으로, BT는 6~30초로 변화시키면서, 그 영향을 180분 운전 후 막오염에 의한 저항$(R_f)$, 투과선속(J)과 총여과부피$(V_T)$ 측면에서 고찰하였다. 광촉매 코팅 구의 농도가 감소할수록 $R_f$는 증가하고 J는 감소하였다. 광촉매 코팅 구의 농도 40 g/L 에서 $V_T$가 8.85 L로 가장 높았다. FT 변화 실험에서는 FT가 감소할수록, $R_f$는 감소하고 J는 증가하였다. 한편, BT 변화 실험에서는 BT가 증가할수록, $R_f$는 감소하고 J는 증가하였다. 또한, NBF(no back-flushing)에서 급격한 막오염에 의한 분리막 기공의 감소로 탁도 및 용존유기물($UV_{254}$ 흡광도)이 효과적으로 제거되었기 때문에, 탁도 및 용존유기물의 처리효율이 NBF 조건에서 가장 높았다. 한편, 광촉매 코팅 구의 세척 효과로 FT가 감소할수록, BT가 증가할수록 탁도 및 용존유기물의 처리효율은 증가하였다.

• Korean Membrane Journal
• /
• 제9권1호
• /
• pp.12-17
• /
• 2007

We performed periodic water-back-flushing using permeate water to minimize membrane fouling to enhance permeate flux in tubular ceramic microfiltration system for water treatment of high turbid source. The filtration time (FT) = 2 min with periodic 6 sec water-back-flushing showed the highest value of dimensionless permeate flux ($J/J_o$), and the lowest value of resistance of membrane fouling ($R_f$), and we acquired the highest total permeate volume $(V_T)\;=\;6.805L$. Also in the result of BT effect at fixed FT = 10 min and BT (back-flushing time) = 20 sec showed the lowest value of $R_f$ and the highest value of $J/J_o$, and we could obtain the highest $V_T\;=\;6.660\;L$. Consequently, FT = 2 min and BT = 6 sec could be the optimal condition in water treatment of high turbid source above 10 NTU. However, FT = 10 min and BT = 20 sec was superior to reduce operating costs because of lower back-flushing frequency. Then the average quality of water treated by our tubular ceramic MF system was turbidity of 0.07 NTU, $COD_{Mn}$ of 1.86 mg/L and $NH_3-N$ of 0.007 mg/L.

• Bulletin of the Korean Chemical Society
• /
• 제23권12호
• /
• pp.1729-1732
• /
• 2002

The LB71350,(3S, 4R)-Epoxy-(5S)-[[N-(1-methylethoxy)carbonyl]-3-(methylsulfonyl)-L-valinyl]amino]-N-[2-methyl-(1R)-[(phenyl)carbonylpropyl-6-phenylhexanamide, is a novel HIV protease inhibitor. Its equilibrium solubility at room temperature was less than $40{\mu}g/mL.$ It was speculated that the low aqueous solubility might be due to the high crystalline lattice energy resulting from intermolecular hydrogen bonds. The present study was carried out to learn the solid-state characteristics of LB71350 using analytical methods such as NMR, FT-IR and XRD. $^{13}C$ Solid-state NMR, solution NMR, and FT-IR spectra of the various solid forms of LB71350 were used to identify the conformation and structure of the solid forms. The chemical shifts of $^{13}C$ solid-state NMR spectra suggest that the crystalline form might have 3 intermolecular hydrogen bondings between monomers.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.540-543
• /
• 1999

In order to determine what indluences the interfacial breakdown in EPDM/XLPE laminates. We studied the interfacial breakdown phenomena at several interfacial conditions. Breakdown strength in laminates pasted with silicone oil was higher than that with silicone grease. As a function of heat treatment time in a vacuum, interfacial breakdown strength increased much in XLPE/EPDM laminates pasted with silicone grease but increased a little in that with silcone oil. FT-IR spectrum of silicone oil was similar to that is silicone grease. FT-lR spectrum of silicone oil was not changed by the heat treatment in a vacuum, but in silicone grease another peak appeared.

• 핵의학기술
• /
• 제20권2호
• /
• pp.75-79
• /
• 2016

Purpose The ASAN Medical Center, Nuclear Medicine performs TSH (Thyroid stimulating hormone) and FT4 (Free Thyroxine) tests 8 times per day. Accordingly, 70 ~ 80 kit tubes are consumed every day for the measurements and the time consumed for reagent dispensing averages over 170 seconds, where the TAT (turnaround time) may be effected when the number of test samples is larger than expected. Therefore, the following test was conducted with the purpose to reduce the number of kit tubes consumed, and reduce the time for reagent dispensing. Materials and Methods The test is based on applying the same reagent for tests where the number of samples is 30 or less. The test for TSH was conducted 9 times from July $1^{st}$ 2015 to July $10^{th}$ 2015. The test for FT4 was conducted 4 times from June $18^{th}$ 2015 to June $22^{nd}$, 2015. Standard Solution No.2 (0.153 uU/mL) and No.5 (4.96 uU/mL) was selected as the two-point standards for the TSH test, and Standard Solution No.3 (0.777 ng/dL) and No.4 (2.044 ng/dL) was selected as the two-point standards for the FT4 test. 38 test samples were subject to correlation analysis. Results For TSH, the result of the normal test shows ranges of 0.20 ~ 0.37 uU/mL for Control1, 0.53 ~ 0.71 uU/mL for Control2, and 6.77 ~ 7.94uU/mL for Control3, while the result of two-point calibration curve test shows ranges of 0.18 ~ 0.27 uU/mL for Control1, 0.53 ~ 0.71 uU/mL for Control2, and 7.30 ~ 8.52 uU/mL for Control3. For FT4, the result of the normal test shows ranges of 0.85 ~ 0.94 ng/dL for Control1 and 4.23 ~ 4.57 ng/dL for Control2, while the result of two-point calibration curve test shows ranges of 0.61 ~ 0.75 ng/dL for Control1 and 3.88 ~ 5.71 ng/dL for Control2. For TSH, the CV% of the normal test for Control1, Control2 and Control3 are 10.5, 3.3 and 3.6 respectively, while the CV% of the two-point calibration curve test for Control1 and Control1 are 12.4, 8.2 and 5.1 respectively. The result shows an outstanding correlation of TSH: y = 0.9985x - 0.0459 $R^2=0.9986$. For FT4, the CV% of the normal test for Control1 and Control2 are 0.70 and 0.71 respectively, while the CV% of the two-point calibration curve test for Control1 and Control1 are 8.7 and 16.2 respectively. The result shows an outstanding correlation of FT4: y = 1.2674x - 0.1133 $R^2=0.9824$. Conclusion The two-point calibration curve can be efficiently applied for TSH in cases where the number of test samples is not large, since the number of samples to be re-tested increases when the result is abnormal from the calibration curve. The two-point calibration curve test should not be applied for FT4 where the results do not consistently comply with the quality assessment range. Depending on how the two-point calibration curve is applied, up to 5 test tubes can be conserved per test, and the reduced time for reagent dispensing is anticipated to have a positive effect on the TAT (turnaround time).

• 멤브레인
• /
• 제18권1호
• /
• pp.26-34
• /
• 2008

본 연구에서 처리수를 이용한 주기적인 역세척은 세라믹 정밀여과에 의한 고도정수처리 시스템에서 막오염을 저감하고 투과선속을 향상시키고자 수행되었으며, 물 역세척 주기(FT) 및 시간(BT)의 영향과 최적 운전조건을 규명하고자 하였다. FT의 영향을 알아보기 위해 일정한 BT 3초에서 FT를 $30{\sim}120$초로 변화시켰고, BT 영향 실험에서 일정한 FT 120초에서 BT를 $3{\sim}12$초로 변화시켰다. 그리고 다른 운전변수인 막간압력차는 1.52 bar, 물 역세척 압력 0.98 bar, 유입유량 0.5 L/min, 공급액의 온도 $20^{\circ}C$로 일정하게 유지하였다. 그 결과, 일정한 BT 3초에서 본 실험 범위의 최적 FT는 30초로, 이것은 빈번한 역세척이 막오염의 저감에 더 효과적임을 의미한다. 그러나 너무 짧은 BT로 인하여 FT의 영향은 크지 않았다. 한편, 일정한 FT 120초에서 BT가 증가함에 따라 막오염에 의한 저항($R_f$)은 감소하고 투과선속(J)과 무차원화한 투과선속 ($J/J_o$)은 증가하는 경향을 나타내어, 최대 BT인 12초에서 가장 많은 총여과부피($V_T$)를 얻을 수 있었다.

• 생명과학회지
• /
• 제31권2호
• /
• pp.175-182
• /
• 2021

기능성 화장품 소재로서 활용할 수 있는 효모의 분리를 위하여 순창군 베리류 및 과수원 토양에서 분리주 80종을 1차로 선별하였다. 80종의 분리주를 대상으로 항산화 활성 및 tyrosinase 저해 활성을 측정한 결과 DPPH 라디칼 소거능은 51.41%, SOD 활성은 62.23%, tyrosinase 저해 활성 64.75%로 가장 우수한 FT4-4를 최종적으로 선별하였다. 18S rRNA 염기서열 분석을 통해 Saccharomyces cerevisiae FT4-4로 명명하였으며, API ZYM을 이용하여 세포 외 효소 활성을 추가로 측정하였다. 발효 시간에 따른 균체 성장 및 tyrosinase 저해 활성의 변화를 측정한 결과 배양 후 16시간에 최대 균체량인 3.16 g/l와 67.68%의 tyrosinase 저해활성을 나타내었다. 또한, S. cerevisiae FT4-4의 화장품 소재로 활용하기 위한 세포 독성과 melanoma B16F10 세포 멜라닌 억제능을 확인한 결과, 세포독성은 50 mg/ml 이하의 농도에서 100% 이상의 세포 생존율을 보였으며, 시료 10 mg/ml에서의 멜라닌 생합성 저해능은 72.02%로 측정되었다. 향후 FT4-4의 화장품 소재로 활용하기 위해서는 생산 수율을 증가하기 위한 생산조건 확립 이외에도 안전성을 향상시키기 위한 추가적인 독성연구 등 다양한 연구가 수반되어야 하나, 본 연구에서의 항산화 및 미백 효능만으로도 충분히 활용할 가치가 있는 소재로 사료된다.

• 한국화재소방학회논문지
• /
• 제33권3호
• /
• pp.1-8
• /
• 2019

ISO TC 92에서는 콘칼로리미터의 연소가스를 FT-IR 방식의 가스분석기로 분석하기 위한 표준을 개발하고 있다. 2018년에는 표준 초안(WD 21397)의 절차에 따라 6개 기관이 참여하여 표준 초안의 반복성 및 재현성을 평가하였다. 시험대상 시료는 polymethyl methacrylate (PMMA), 경질 폴리우레탄 보드 및 PVC 장판이었고 콘칼로리미터 시험결과 중 착화시간(s), 최대 열방출률(kW·m^-2), 총 방출열량(MJ·m^-2) 및 유효연소열(MJ·m^-2·kg^-1)을, 그리고 FT-IR 가스분석결과 중 독성가스의 최대 농도(µL·L^-1), 가스 발생량(g) 및 가스 수율(g·g^-1)을 ISO 5725-2에 따라 통계 분석하여 정밀도를 평가하였다. 이상치(outlier)는 발견되지 않았으며 콘칼로리미터 시험의 반복성(sr/m)은 1.5%, 재현성(sR/m)은 9.8%로 나타났고 FT-IR 가스분석의 반복성은 12.9%, 재현성은 27.9%로 나타났다.

• 대한화장품학회지
• /
• 제27권1호
• /
• pp.3-15
• /
• 2001

The bilayer forming ability of pseudo-ceramide PC104 in octanoic acid/water/n-octyl $\beta$-D-glucoside mixtures was investigated through the phase diagram. Because of its low solubility in water and of its crystallization, pseudoceramide PC104 was dissolved in octanoic acid, which is nontoxic additive for foods and cosmetics. The mixtures formed four different phases (L1, L2, LC and two phases). Depending on the concentration of PC104 in octanoic acid, the region of each phase was extended or contracted. On the contrary to the region of L2, regions of lamellar phase and L1 phase were expanded. The bilayer-forming ability of PC104 was explained on the basis of concentration of PC104 at interface and interaction between PC104 and octanoic acid. From FT-IR results, it was found that the interactions of PC104’s polar head group with octanoic acid increased as the amount of PC104 in octanoic acid increased. Also emulsion size and size distribution have been studied depending upon the emulsification path. droplets of emulsion prepared from lamellar phase were smaller and more homogeneous compared to those of emulsions formed from L2 phase.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.447-450
• /
• 2001

Abstract-Si direct bonding(SDB) technology is very attractive for both Si-on-insulator(SOI) electric devices and MEMS applications because of its stress free structure and stability. This paper presents on pre-bonding according to HF pre-treatment conditions in Si wafer direct bonding. The characteristics of bonded sample were measured under different bonding conditions of HF concentration, and applied pressure. The bonding strength was evaluated by tensile strength method. The bonded interface and the void were analyzed by using SEM and IR camera, respectively. Components existed in the interlayer were analysed by using FT-lR. The bond strength depends on the HF pre-treatment condition before pre-bonding (Min : 2.4kgf/cm$^2$∼Max : 14.9kgf/cm$^2$).