• 한국진공학회지
• /
• 제9권1호
• /
• pp.42-47
• /
• 2000

The amorphous vanadium oxide thin films for thin-film rechargeable lithium batteries were fabricated by r.f. reactive sputtering at room temperature. As the experimental parameter, oxygen partial pressure was varied during sputtering. At high oxygen partial pressures(>30%), the as-deposited films, constant current charge/discharge characteristics were carried out in 1M $LiPF_6$, EC:DMC+1:1 liquid electrolyte using lithium metal as anode. The specific capacity of amorphous $V_2O_5$ after 200cycles of operation at room temperature was higher compared to crystalline $V_2O_5$. The amorphous vanadium oxide thin film and crystalline film showed about 60$\mu$Ah/$\textrm{cm}^2\mu\textrm{m}$ and about 38$\mu$Ah/$\textrm{cm}^2\mu\textrm{m}$, respectively. These results suggest that the battery capacity of the thin film vanadium oxide cathode strongly depends on the crystallinity.

• 한국정밀공학회지
• /
• 제3권2호
• /
• pp.62-75
• /
• 1986

An experimental investigation of the machining characteristics such as cutt- ing resistance, surface roughness and tool wear in turning the test pieces of SM45C steel with both coated and uncoated carbide tool tips under various cutting conditions was conducted. Also a specially designed simple vibration damping device was experimentally evaluated for its effectiveness on machined surface roughness and a vibration test was conducted to confirm its ability to reduce the amplitude. Based on these tests finding, the following conclusions are made; 1. The cutting resistance($\textrm{p}_{1}$) increases as the depth of cut(d) increases at fixed feed rate(f) over the cutting speed(v) range of 43-226 m/min and p decreses about 18% average when V is increased for fixed d and f. At V= 226m/min, $\textrm{p}_{1}$/for A, C tips are about the same level but $\textrm{p}_{1}$ for B tip is 15% less than A, C tips. 2. The specific cutting resistance(Ks) at V=226 m/min was derived for A, B, C tips respectively and the value of Ks for B rip is about 20% less than A, C tips. 3. The surface roughness(Ra) improves significantly as the cutting speed(V) is increased and this effect was greater when V>100 m/min. On the other hand, Ra deteriorates as the feed rate(f) is increased and this trend was accelerated when f>0.3 mm/rev. With regard to the difference of Ra values among A, B, C tips, at V=226m/min, d=0.4mm, and f=0.31-0.61mm/rev, Ra values for B.C tips are about 17% less than tip A. 4. The experimental tool wear equations were derived for A, B, C tips and from these equations, the tool life($\textrm{T}_{\textrm{L}}$) baced on the I.S.O. criteria was calculated to be $\textrm{T}_{\textrm{L}}$<$\textrm{T}_{\textrm{LB}}$<$\textrm{T}_{\textrm{LC}}$ for both flank wear($\textrm{V}_{\textrm{B}}$) and boundary wear($\textrm{V}_{\textrm{N}}$). Hence, the coated tips are superior to the uncoated tip and tip C is considered to be the best. 5. The cutting resistance may be slightly reduced and the surface rounghness improved when the damper is used especially when V>100 m/min. Therefore this damping device is considered to be effective and practical. The experimental surface roughness equations were also derived. Based on the vibration test, it is established that the surface roughness improvement was the result of amplitude reduction made possible by the damper.

• 센서학회지
• /
• 제6권1호
• /
• pp.63-71
• /
• 1997

ZnS:Mn/$ZnS:TbF_{3}$적층구조의 TFEL(thin-film eletroluminescent)소자를 제작하였으며, 이때 절연층으로 (Pb,La)$TiO_{3}$(이하PLT)와 $SiO_{2}$박막을 이용하였다. TFEL소자는 $78V_{rms}$의 문턱전압과 $100V_{rms}$의 인가전압에서 $400{\mu}W/cm^{2}$의 휘도를 나타내었다. TFEL소자의 발광스펙트럼은 450nm에서 630nm사이의 파장대를 보이고 있다. 제작된 TFEL소자는 컬러필터를 병용함으로서, 적 녹 청의 색상을 구현하는 TFEL소자로 활용할 수 있다.

• 한국진공학회지
• /
• 제10권1호
• /
• pp.51-56
• /
• 2001

MFISFET(Metal-ferroelectric-insulator-semiconductor-field effect transistor)에의 적용을 위한 절연체로서 CeO$_2$ 박막을 r.f. magnetron sputtering법에 의해 제조하였다. 스퍼터링시 증착개스는 Ar과 $O_2$를 사용하였으며 산소분압비에 따른 $CeO_2$박막의 결정성 및 전기적 특성에 미치는 영향을 평가하였다. p형-Si(100)기판 위에 $600^{\circ}C$에서 증착된 $CeO_2$ 박막들은(200)방향으로 우선방향성을 가지고 성장하였으며 Ar만으로 증착된 박막의 우선방향성은 증가하였으나 상대적으로 많은 하전입자와 표면 거칠기로 인해 C-V특성에서 큰 이력특성을 보였고 산소분압비가 증가함에 따라 양호한 특성을 보였다. 이것은 이동가능한 이온전하의 감소에 기인한다고 할 수 있다. Ce:O의 비는 모든 박막에서 1:2.22~2.42를 보여 산소과잉의 조성을 나타냈으며 산소분압비에 따라 제조된 박막들의 누설전류값은 100 kV/cm의 전계에서 $10^{-7}$~$10^{-8}$A의 차수를 보였다.

• Bulletin of the Korean Chemical Society
• /
• 제29권1호
• /
• pp.139-147
• /
• 2008

New PPV derivatives which contain electron-withdrawing CF3F4phenyl group, poly[2-(2-ethylhexyloxy)-5-(2,3,5,6-tetrafluoro-4-trifluoromethylphenyl)-1,4-phenylenevinylene] (CF3F4P-PPV), and poly[2-(4-(2-etylhexyloxy)-phenyl)-5-(2,3,5,6-tetrafluoro-4-trifluoromethylphenyl)-1,4-phenylenevinylene] (P-CF3F4P-PPV), have been synthesized by GILCH polymerization. As the result of the introduction of the electron-withdrawing CF3F4phenyl group to the phenyl backbone, the LUMO and HOMO energy levels of CF3F4P-PPV (3.14, 5.50 eV) and P-CF3F4P-PPV (3.07, 5.60 eV) were reduced. The PL emission spectra in solid thin film are more red-shifted over 50 nm and increased fwhm (full width at half maximum) than solution conditions by raising aggregation among polymer backbone due to electron withdrawing effect of 2,3,5,6-tetrafluoro-4-trifluoromethylphenyl group. The EL emission maxima of CF3F4P-PPV and P-CF3F4P-PPV appear at around 530-543 nm. The current density-voltage-luminescence (J-V-L) characteristics of ITO/PEDOT/polymer/Al devices of CF3F4P-PPV and P-CF3F4P-PPV show that turn-on voltages are around 12.5 and 7.0 V, and the maximum brightness are about 82 and 598 cd/m2, respectively. The maximum EL efficiency of P-CF3F4P-PPV (0.51 cd/A) was higher than that of CF3F4P-PPV (0.025 cd/A).

• 한국지반공학회논문집
• /
• 제21권6호
• /
• pp.101-115
• /
• 2005

국내 내륙의 지형 및 지질 특성을 대표하는 두 지역인 경주와 홍성을 대상으로 전단파 속도$(V_s)$ 획득 목적의 현장 탄성파 시험을 포함한 다양한 지반 조사를 실시하여 지반 특성을 평가하고, 이를 토대로 등가 선형 및 비선형 기법의 부지 응답 해석을 수행하였다. 현행 국내 내진 설계의 근간인 미국 서부 지역과의 지반 특성 비교 결왔 국내 내륙 지역의 기반암 심도는 매우 얕고 강성은 다소 컸다. 지반 분류 기준인 심도 30m까지의 평균 전단파 속도$V_s30$는 대상 지역 내에서 $250\sim650m/s$의 좁은 범위의 분포를 보였고, 그에 따라 대부분의 부지가 C와 D 지반 조건으로 분류되었다. 부지 응답 해석 결과로부터 현행 국내 내진 설계를 위한 단주기 증폭 계수$(F_ㅁ)$는 지반 운동을 과소평가하고 중장주기 증폭계수$(F_v)$는 과대평가하고 있음을 확인하였다. 이에 따라 국내 내륙 지역에 대한 지반 증폭 계수를 재산정하고, 지역적 지반 특성을 고려하여 기존 지반 분류 C 및 D의 세부 분류와 지표면 부근 심도까지의 평균 $V_s$인 $V_s20,\;V_s15,$ 와 $V_s10$의 추가 분류 기준이 적용된 합리적 지반 분류 체계를 제안하였다. 제안된 지반 분류 체계는 현재로서는 예비적인 방안이므로 향후 보완 및 개선이 필요할 것으로 판단된다.

• 한국광학회지
• /
• 제6권3호
• /
• pp.214-221
• /
• 1995

레이저매질의 넓은 압력범위(0.5-3.5 기압)에 대해 70ns[FWHM]의 전자빔 가속기(800kV, 21kA)로 여기할 때 free-running XeF$(C\rightarrowA$ 엑시머 레이저의 출력과 Xe 농도와의 상호관계를 조사하였다. 공진기를 쌍색성의 출력거울로 구성하고, 레이저 출력을 레이저매질 $(Xe/F_2/Ar)$의 총압력과 가스혼합비의 함수로써 최적화 하였다. $F_2$ 0.46%를 고정한 조건에서 레이저 고유효율은 총압력 1, 2, 3기압에서 최대 0.38%, 1.03%, 0.29%로 측정되었다. 이때 레이저의 최대 고유효율은 레이저매질의 총압력이 낮을수록 높은 Xe 농도에서 높게 나타났다. 이같은 상호관계를 $XeF^*(C)$의 형성효율 및 XeF$(C\rightarrowA$ 레이저 추출 효율에 대해 동력학적으로 해석하므로써 Xe 농도의 의존성을 설명하였다. 그 결과로 대기압 XeF$(C\rightarrowA$ 레이저의 효율적인 동작을 제안한다.

• Nuclear Engineering and Technology
• /
• 제52권7호
• /
• pp.1503-1510
• /
• 2020

Ultra-low noise charge sensitive amplifiers (CSAs) based on various types of circuit board substrates, such as FR4, Teflon, and ceramics (Al₂O₃) with two different designs, PA1 and PA2, have been developed. They were tested to see the noise effect from the dielectric loss of the substrate capacitance before and after irradiation. If the electronic noise from the CSAs is to be minimized and the energy resolution enhanced, the shaping time has to be optimized for the detector, and a small feedback capacitance of the CSA is favorable for a better SNR. Teflon- and ceramic-based PA1 design CSAs showed better noise performance than the FR4-based one, but the Teflon-based PA1 design showed better sensitivity than ceramic based one at a low detector capacitance (<10 pF). In the PA2 design, the equivalent noise and the sensitivity were 0.52 keV FWHM for a silicon detector and 7.2 mV/fC, respectively, with 2 ㎲ peaking time and 0.1 pF detector capacitance. After 10, 100, 10³, 10⁴, and 10⁵ Gy irradiation the ENC and sensitivity characteristics of the developed CSAs based on three different substrate materials are also discussed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.1015-1018
• /
• 2004

We investigate the influence of the New Electron Injection Layers (EIL) on the performance of the Alkali Metal Complex vapor-deposited Organic Light Emitting Diodes(OLED). Two different Alkali Metal Complex were used; Lithium Quinolate (Liq), and Sodium Quinolate (Naq). In all cases, $Alq_3$ was the Electron Transporting Layer (ETL). We measure and compare the current density-voltage (J-V) and luminance-voltage (L-V) characteristics. We concluded that the turn-on voltage, and luminance efficiency are controlled by the type of EIL material used. We show the longer life-time OLED with Alkali Metal Complex EIL than OLED with LiF EIL. And we show the Optimized Alkali Metal Complex thickness is 3nm. Existent LiF to because is inorganic material, there is trouble to do epitaxy into thin layers but regulates the thickness in case of Alkali Metal Complex matter characteristic that is easy be. Alkali Metal Complex also appeared by sensitive thing in thickness than LiF If utilize this material, It is thought much advantages may be at common use of OLED.

• ALGAE
• /
• 제18권4호
• /
• pp.255-262
• /
• 2003

Ecological characteristics of phytoplankton communities were investigated biweekly at 6 stations from Feb. 2001 to Feb. 2002 at the lower part of the Han River. During the study, a total of 267 taxa which were composed of 114 green algae, 104 diatoms, 22 blue-green algae, 13 chrysophytes and 2 dinoflagellates were observed. The standing crops of phytoplankton communities were ranged from 1.30 ${\times}10^6$ cells ${\cdot}l^{-1}$ to 37.47 ${\times}10^6$ cells ${\cdot}l^{-1}$. The dominant species were 11 taxa including Pediastrum duplex, Scenedesmus quadricauda in green algae, Osillatoria limosa, Microcystis aeruginosa, Merisomorpedia sp., Phormidium sp. in blue-green algae, and Asterionella gracillima, Aulacoseira granulata, Fragilaria crotonensis, Stephanodiscus hantzschii f. tenuis, Synedra acus in diatoms. Asterionella gracillima and Stephanodiscus hantzschii f. tenuis were abundant at every station from winter to spring. Stephanodiscus hantzschii f. tenuis occupied the highest dominant ratio and standing crop. From summer to autumn, dominant species were Aulacoseira granulata at all stations and blue-green algae such as Osillatoria limosa, Microcystis aeruginosa, Merisomorpedia sp. at some stations. These 4 species were mostly present at the lower stations 4, 5, 6 and very few at the upper stations 1, 2, 3.