• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.665-668
• /
• 2006

Concrete secondary product that use cement is increasing application from reason of shortening etc.. of construction period in construction site. Manufacture method of construction of this concrete secondary product there is hot-check method, direct spray method, press method, extrusion molding method etc.. Also, I am using reinforcement boating certainly in this process. In most case, We have used asbestos by reinforcement fiber until early 90s but use from human body hurtfulness controversy is felt constraint. Therefore, application of principal parts fiber is increasing. But, to replace asbestos, because must satisfy all lubricating ability, productivity etc.. class, it is the very difficult matter to replace asbestos. In this study, I wished to do Test about asbestos principal parts possibility at extrusion process to charge shape or form making test piece because mixs polypropylene fiber etc. by plan that replace asbestos in cement extrusion molding product and measures bending strength and elasticity.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.359-362
• /
• 2003

The bending phenomenon has been known to be occurred by the different of velocity at the die exit. The difference of velocity at the die exit section can be obtained by the different velocity of billets through the multi-hole container and by the cohesion of billet inside the porthole die chamber. The bending phenomenon can be controlled by the different hole diameter. The experiments using aluminium material for the curved tube product had been done. The results of the experiment show that the curved tube product can be formed by the extru-bending process without the defects such as the distortion of section and the thickness change of the wall of tube and the folding and wrinkling. It is known that the welding and extruding of each billet has done simultaneously although the curved tube is extruded with four billets.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.697-702
• /
• 2002

Composite material made of recycling paper and plastics was developed. The tension and bending testing result of developed composite material shows that the cellulose contained in paper contributes much to get high flexural rigidity. As an application example, the raised access floor for office automation purpose was developed by making use of developed composite material. Manufacturing process together with the extrusion die and the compression die for to manufacture the access floor have been developed.

• Transactions of Materials Processing
• /
• v.10 no.3
• /
• pp.246-246
• /
• 2001

The conventional and new forming processes of a steel shell body are analyzed by the rigid-plastic finite element method. The conventional process contains five forming stages such as bending, drawing, ironing, heading and sizing, which was designed by a forming equipment expert. The results of simulation of the conventional forming process are summarized in terms of deformation patterns and load-stroke relationships for each forming operation. Based on the simulation results of the current five-stage, the shell body forming Process including backward extrusion is designed for improving the conventional process sequence. Forming loads of the proposed process are within the limit value, which is proposed by experts and the proposed process is found to be proper for manufacturing steel shell body.

• Transactions of Materials Processing
• /
• v.10 no.3
• /
• pp.245-252
• /
• 2001

The conventional and new forming processes of a steel shell body are analyzed by the rigid-plastic finite element method. The conventional process contains five forming stages such as bending, drawing, ironing, heading and sizing, which was designed by a forming equipment expert. The results of simulation of the conventional forming process are summarized in terms of deformation patterns and load-stroke relationships for each forming operation. Based on the simulation results of the current five-stage, the shell body forming Process including backward extrusion is designed for improving the conventional process sequence. Forming loads of the proposed process are within the limit value, which is proposed by experts and the proposed process is found to be proper for manufacturing steel shell body.

• Journal of the Korean Ceramic Society
• /
• v.46 no.6
• /
• pp.662-667
• /
• 2009

Porous SiC candle filter preforms were fabricated by extrusion and ramming process. To fabricate SiC candle filter preform, commercially available 85 ${\mu}m\;{\alpha}-$-SiC powder and 44 ${\mu}m$ mullite, CaC$O_3$ powder were used as the starting materials. The candle type preforms were fabricated by vacuum extrusion and ramming process, and sintered at $1400{^{\circ}C}$ 2 h in air atmosphere. The effect of forming method on porosity, density, strength (flexural and compressive strength) and microstructure was investigated. Also, corrosion test of the sintered candle filter specimens as forming method was performed at $600{^{\circ}C}$ in IGCC syngas atmosphere. The sintered SiC filter which was formed by ramming process has more higher density and exhibit higher strength than extruded filter. Its maximum density and 3-point bending strength were 2.00 g/$cm^3$ and 45 MPa, respectively.

• Journal of the Korean Ceramic Society
• /
• v.51 no.5
• /
• pp.406-412
• /
• 2014

In this study, flat-tubular-type alumina filters were manufactured using alumina powder of two sizes ($2.4{\mu}m$ ALM-44 and $0.4{\mu}m$ AP 400) by an extrusion process. The manufactured alumina filter was sintered at $1200-1600^{\circ}C$ for 1 h. As particle size increased, the largest pore size, average pore size and porosity increased; but density and linear shrinkage decreased. The alumina filter fabricated using ALM-44 powder sintered at $1500^{\circ}C$ was confirmed as the best water treatment filter after investigation of the bending strength, water permeability and impurity-removal efficiency of the experimental filters. This flat-tubular-type alumina filter is expected to be useful not only for direct water treatment, but also for use as a support filter during coating processes, to control pore size.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.12
• /
• pp.136-141
• /
• 1996

In this paper, the design variables of the extruded parts involving flat die through model experiment are investigated to overcome some current problems such as bending and twisting and get more improved quality products. Above all, the deformation behavior is analyzed in experiment and investigated flow charactristics inside container. Finally, the straight extruded product is obtained by modified bearing land width on the basis of the exit velocities distribution from bended and twisted products.

• Journal of the Korean Ceramic Society
• /
• v.41 no.7
• /
• pp.560-566
• /
• 2004

To fabricate the continuously porous alumina bodies by multi-extrusion process, carbon powder and ethylene vinyl acetate were used as a pore forming agent and a binder, respectively. As the change of extrusion pass number, reduction ratio as well as the volume fraction of core and tube, the porous alumina bodies having various kind of pore size and porosity could be obtained. The porous bodies showed continuous pore shape, high specific surface as well as high bending strength, which were compared with those of commercial alumina bodies. In-vitro study was carried out using MG-63 osteoblast cells to investigate of their biocompatibility. As a result, the cells grew well on top and bottom as well as inside surface of pore. From the result of in-vivo study of 3-dimensional porous alumina bodies using rats, it was confirmed that any inflammatory response was not found in the subcutaneous tissue around porous body. Also the porous bodies removed from the rats were fully covered with well-developed fibrous tissues and showed the formation of new capillary blood vessels.

• The korean journal of orthodontics
• /
• v.21 no.3
• /
• pp.685-699
• /
• 1991

The purpose of this report is to review vertical dysplasia such as openbite or deep bite in skeletal Class III malocclusion and their treatment modality and to present two cases treated with MEAW. The results obtained were as follows A. Open bite case 1. The treatment time was 3 year 8 months. 2. Upper and lower incisors showed extrusion and especially lower anterior alveolar process showed remodelling. 3. The mesially inclined upper and lower molars were uprighted and especially lower first molars showed extrusion that means remodelling of alveolar bone. 4. Normal overbite and overjet were established. 5. Mandible showed slight clockwise rotation. 6. Maxilla showed slight downward bending of ANS part. 7. Upper lip showed downward drop and lower lip showed retraction and touch between upper and lower lip was established. 8. Tongue posture of post-treatment was more raised than pretreatment. B. Deep bite case 1. The treatment time was 1 year 8 months. 2. Upper incisors showed intrusion and labioversion and lower incisors showed slight intrusion and linguoversion. 3. The lower molars showed distal uprighting and intrusion and upper molars showed mesial movement and extrusion. 4. Normal overbite and overjet were established. 5. Maxilla did not show downward movement. 6. Mandible showed slight clockwise rotation. 7. Lower lip showed retraction and downward drop and upper lip showed downward drop.