• Journal of the Korean Society of Clothing and Textiles
• /
• v.30 no.2 s.150
• /
• pp.296-305
• /
• 2006

This study evaluate the effect of laundering on the deformation of knitted spandex/cotton fabrics compared with that of knitted cotton fabrics. Commercial knitted spandex/cotton and knitted cotton fabrics for T-shits were laundered in a drum-type washing machine and dried in a tumble dryer. Wale spirality, shrinkage, elastic recovery and surface contour of knitted fabrics were investigated under different laundering conditions: washing temperature, presoaking time and washing cycles. Knitted spandex/cotton fabrics had a lower angle of spirality than knitted cotton fabrics. After the first washing cycle, the angles of spirality of all the fabrics had decreased greatly. Knitted cotton fabric of low density deformed more than that of higher density. Knitted spandex/cotton. fabric of low density shrank less, because of the greater extension given during heat-set. Permanent elongation length at the 80$\%$ extension was longer than at the 50$\%$ extension, and the knitted spandex/cotton fabric which was expanded greatly during heat-set had a lower elastic recovery rate. The surface appearance of the knitted spandex/cotton fabrics was worsl~ than that of the knitted cotton fabrics before laundering and after repeated laundering, because of the much protruded cotton fibers from the yarns.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.8
• /
• pp.842-848
• /
• 2009

Fatigue failures are often occurred at welded joints where stress concentrations are relatively high due to the joint geometry. Although employing good detail design practices by upgrading the welded detail class enables to improve the fatigue performance, in many cases, the modification of the detail may not be practicable. As an alternative, the fatigue life extension techniques that reduce the severity of the stress concentration at the weld toe region, remove imperfections and introduce local compressive welding residual stress, have been applied. These techniques are also used as definite measures to extend the fatigue life of critical welds that have failed prematurely and have been repaired. In this study, a hammer peening procedure for using commercial pneumatic chipping hammer was developed, and the effectiveness is quantitatively evaluated. The pneumatic hammer peening makes it possible to give the weld not only a favorable shape reducing the local stress concentration, but also a beneficial compressive residual stress into material surface. In the fatigue life calculation of non-load carrying cruciform specimen treated by the pneumatic hammer peening, the life was lengthened about ten times at a stress range of 240MPa, and fatigue limit increased over 65% for the as-welded specimen.

• Proceedings of the KSRS Conference
• /
• 2007.10a
• /
• pp.33-36
• /
• 2007

We have persistently constructed gridded products of surface wind/wind stress over the world ocean using satellite scatterometer (ERS and Qscat). They are available for users as the Japanese Ocean Flux data sets with Use of Remote sensing Observation (J-OFURO) data together with heat flux components. Recently, a new version data of the Qscat/SeaWinds based on improved algorithm for rain flag and high wind-speed range have been delivered, and allowed us to reconstruct gridded product with higher spatial resolution. These products are validated by comparisons with in-situ measurement data by mooring buoys such as TAO/TRITON, NDBC and the Kuroshio Extension Observation (KEO) buoys, together with numerical weather prediction model products such as the NCEP-1 and 2. Results reveal that the new product has almost the same magnitude in mean difference as the previous version of Qscat product and much smaller than the NCEP-1 and 2. On the other hand, it is slightly larger root-mean-square (RMS) difference than the previous one and NCEPs for the comparison using the KEO buoy data. This may be due to the deficit of high wind speed data in the buoy measurement. The high resolution product, together with sea surface temperature (SST) one, is used to examine a new type of relationship between the lower atmosphere and upper ocean in the Kuroshio Extension region.

• Journal of Surface Science and Engineering
• /
• v.49 no.5
• /
• pp.447-453
• /
• 2016

In this study, we intended to extend the life of electropolishing solution through the reduction of electric resistance by improving the electrolysis efficiency. The optimum conditions were obtained by half round bus bar and Taguchi method. As the main control factors in the electropolishing process, current density, polishing time, electrolyte temperature and flow rate were selected. The electrolyte temperature was the most significant to the electrolysis efficiency. The optimum conditions for the life extension of electropolishing solution were as follows: current density, $45A/dm^2$; polishing time, 6 min; electrolyte temperature, $70^{\circ}C$; flow rate, 11 L/min. As a results of ANOVA of SN ratios, it was found that the electrolyte temperature was significant factor at the 90% confidence level.

• Food Science and Preservation
• /
• v.30 no.6
• /
• pp.905-917
• /
• 2023

The optimal fermentation conditions for producing fermented black soybeans rich in sulfur-containing amino acids were investigated. Response surface methodology monitored fermentation conditions. A central composite design examined the effect of independent variables: enzyme concentration (X₁) and fermentation time (X₂) on yield and methionine content. Both factors significantly influenced these dependent variables. Enzyme concentration more profoundly affected amino nitrogen content than fermentation time. β-Glucan content and cystine level were primarily affected by fermentation time. We elicited each variable's regression formula and identified optimal fermentation conditions for functional compounds. The predicted optimum conditions were an enzyme concentration of 0.28-0.32% and a fermentation time of 58.0-62.0 min. Under these optimal conditions, each black soybean variety's sulfur amino acid content ranged from 818.62 to 922.62 mg/100 g, demonstrating significant variety differences.

• The Korean Journal of Mycology
• /
• v.38 no.2
• /
• pp.205-207
• /
• 2010

Stem and petiole rot symptoms of Valeriana fauriei occurred sporadically in the herb exhibition field in Gyeongsangnam-do Agricultural Research and Extension Services, Hamyang-gun, Gyeongnam Province in Korea. The typical symptom is water-soaking on the stem, rotting, wilting, blighting and the infected plants eventually died. White mycelial mats spreaded over lesions, and then sclerotia were formed on the infected plant parts and near soil surface line. On the basis of mycological characteristics and pathogenicity to host plants, this fungus was identified as Sclerotium rolfsii. This is the first report of stem rot on Valeriana fauriei caused by Sclerotium rolfsii in Korea.

• Korean Journal of Soil Science and Fertilizer
• /
• v.44 no.4
• /
• pp.534-538
• /
• 2011

One of the problems for cultivating crops in the mountainous highland is soil erosion and nutrients runoff. Alternative cropping ways were searched to reduce soil erosion and to ensure farm income in the mountainous highland agricultural region. Three edible wild plants including goatsbeard, Korean thistle, and aster, were selected to test as alternative crops to reduce soil erosion in mountain agriculture of highland area. In the first year, the soil losses from the alternative cropping were 26 to 63 percents of the soil loss from summer radish cultivated by conservation tillage with contour and plastic film mulching. The relative soil losses in the second year ranged from 2.8 to 5.5 percents in comparison with radish cultivation. Rapid surface coverage contributed to successive soil loss protection by these alternative crops. Farm net profit of these crops was greater than that of radish. Monitoring of yields of Korean thistle or aster for further experiments, however, might be necessary for economic cultivation due to yield reduction caused by consecutive production.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.10
• /
• pp.948-956
• /
• 2010

The purpose of this study was to test the effectiveness of a prototype KAFO (Knee-Ankle-Foot Orthosis) powered by two artificial pneumatic muscles during walking. We had previously built powered AFO (Ankle-Foot Orthosis) and KO (Knee Orthosis) and used it effectively in studies on assistance of plantaflexion and knee extension motion. Extending the previous study to a KAFO presented additional challenges related to the assistance of gait motion for rehabilitation training. Five healthy males were performed gait motion on treadmill wearing KAFO equipped with artificial pneumatic muscles to power ankle plantaflexion and knee extension. Subjects walked on treadmill at 1.5 km/h under four conditions without extensive practice: 1) without wearing KAFO, 2) wearing KAFO with artificial muscles turned off, 3) wearing KAFO powered only in plantaflexion under feedforward control, and 4) wearing KAFO powered both in plantaflexion and knee extension under feedforward control. We collected surface electromyography, foot pressure and kinematics of ankle and knee joint. The experimental result showed that a muscular strength of wearing KAFO powered plnatarfexion and knee extension under feedforward control was measured to be lower due to pneumatic assistance and foot pressure of wearing KAFO powered plnatarfexion and knee extension under feedforward control was measured to be greater due to power assistance. In the result of motion analysis, the ankle angle of powered KAFO in terminal stance phase was found a peak value toward plantaflexion and there were difference of maximum knee flexion range among condition 2, 3 and 4 in mid-swing phase. The current orthosis design provided plantaflexion torque of ankle jonit in terminal stance phase and knee extension torque of knee joint in mid-swing phase.

• Journal of the Korean Society of Safety
• /
• v.17 no.1
• /
• pp.99-104
• /
• 2002

DQM(differential quadrature method) is applied to computation of eigenvalues of the equations of motion governing the free in-plane vibration for circular curved beams including mid-surface extension and the effects of rotatory inertia. Fundamental frequencies are calculated for the members with various end conditions and opening angles. The results are compared with numerical solutions by other methods for cases in which they are available. The differential quadrature method gives good accuracy even when only a limited number of grid points is used.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.4 s.181
• /
• pp.168-175
• /
• 2006

This paper presents surface matching algorithms that can be used to reconstruct the surface topography of an object scanned by an AFM. The essence of the algorithms is to match up neighboring images intentionally overlapped with others. Two performance indexes using the correlation coefficient and the sum of the squared differences are introduced. To compensate for the inaccuracy of the coarse stage implemented to AFM, all the six axes including the rotational degrees of freedom are successively matched so as to maximize the coefficients defined. The results show that the proposed algorithms are useful for measurement range extension of AFM. The results also show that a combined use of the two indexes is beneficial for practical cases.