• Journal of Korean Society for Atmospheric Environment
• /
• v.33 no.5
• /
• pp.521-528
• /
• 2017

In the combustion treatment of explosive gases with a high heating value such as $H_2$ and $NH_3$ used in semiconductor and chemical processes, the heat recovery modeling and exergy analysis of the process using the Aspen Plus simulator and its thermodynamic data were performed to examine the recovery of high temperature thermal energy. The heat recovery process was analyzed through this process modeling while the exergy results clearly confirmed that the rigorous reaction mainly occurs in the condenser and the chamber. In addition, the process modeling demonstrated that approximately 95% of the exergy is destructed on the basis of the exergies injected and the exergy being exhausted. Using the exergy technique, which can quantitatively analyze the energy, we could understand the energy flow in the process and confirm that our heat recovery process was efficiently designed.

• Journal of Sensor Science and Technology
• /
• v.31 no.5
• /
• pp.348-352
• /
• 2022

Hydrogen gas (H₂) which is odorless, colorless is attracting attention as a renewable energy source in varions applications but its leakage can lead to disastrous disasters, such as inflammable, explosive, and narcotic disasters at high concentrations. Therefore, it is necessary to develop H₂ gas sensor with high performance. In this paper, we confirmed that H₂ gas detection ability of SnO₂ based H₂ gas sensor along with thermal treatment effect of SnO₂. Proposed SnO₂ based H₂ gas sensor is fabricated by MEMS technologies such as photolithgraphy, sputtering and lift-off process, etc. Deposited SnO₂ thin films are thermally treated in various thermal treatement temperature in range of 500-900 ℃ and their H₂ gas detection ability is estimatied by measuring output current of H₂ gas sensor. Based on experimental results, fabricated H₂ gas sensor with SnO₂ thin film which is thermally treated at 700 ℃ has a superior H₂ gas detection ability, and it can be expected to utilize at the practical applications.

• Journal of the Korean Institute of Gas
• /
• v.22 no.2
• /
• pp.84-89
• /
• 2018

Recently, many studies have focused on the explosive waste treatment in terms of the safety and environmental pollution. A combustion process using fluidized bed incinerator has several profits : continuous process, low pollutive gases such as NOx, and high process efficiency. This study focused on the design of the propellant combustion reactor by using computational fluid dynamics(CFD) simulation technique. As a result, the reactions are successfully simulated in cylindrical incinerator, and. The study will influence to the research about treatment of explosive wastes.

• Journal of the Korean Society of Safety
• /
• v.39 no.3
• /
• pp.14-19
• /
• 2024

Hydrogen is one of the most popular eco-friendly energy sources for reducing global warming. To use hydrogen as a conventional fuel, liquid hydrogen plants should introduce waste hydrogen treatment processes. A major safety issue of liquid hydrogen plants is choosing the most suitable purge gas to use in case of an accident. A purge gas prevents the formation of explosive mixed gases in the vent header. In general, nitrogen is the main purge gas used in chemical plants. Nitrogen has a freezing point of -210℃, which is higher than the boiling point of hydrogen. Helium, with a freezing point lower than hydrogen, is instead recommended as a purge gas of the vent header during hydrogen liquefaction. However, helium is roughly 100 times more expensive than nitrogen. To address this issue, this study uses simulations to investigate safe conditions for introducing nitrogen as the purge gas during hydrogen liquefaction. The temperature change from the safety valve to the vent header is evaluated when the external temperature of the safety valve discharge pipe is at 5℃, 10℃, and 20℃. Additionally, the most optimal length for a discharge pipe according to pipe diameter is investigated.

• Nuclear Engineering and Technology
• /
• v.31 no.6
• /
• pp.541-547
• /
• 1999

Corrosion control, in the end-shield cooling system of Wolsung Nuclear Power Plant, is directly related to the control of dissolved oxygen (DO). The current method, being used to deoxygenate the end-shield cooling water, is a chemical treatment by addition of reducing agent, hydrazine, to react with DO. This method has several limitations including high reaction temperature of hydrazine , unwanted explosive hydrogen gas production, and its intrinsic harmful property. A new approach to remove DO using a membrane-based oxygen removal system (MORS) was tried to overcome limitations of the hydrazine treatment. The DO removal efficiency of the MORS was found to be in the range 87% to 98%: The higher vacuum, the lower water flow rate and the higher water temperature tend to increase the DO removal efficiency.

• 한국연소학회:학술대회논문집
• /
• 2006.10a
• /
• pp.42-45
• /
• 2006

A new and reusable energy source is water-treatment sludges. There is a significant need for understanding the characteristics of sludge combustion related to improving efficiency and ensuring the safety of this new energy source. Because sludges are composed of solids and gas mixture, the combustion of the mixture may become quite complex. Not only decomposition of conventional organic elements but also dust explosion may be important during the process of converting sludges into a new and safe form of energy. Sludge combustion mainly involves hydrogen, methane, hydro carbons, carbon, and organic particles. Dust explosion during the gasification stage may depend on the surrounding temperature and the composition of gases. The uncertainty in the explosive behavior of energetic source is noted in this work. We study the explosion characteristics of sludge combustion while the reusability of sewage sludges as a new form of energy is also investigated.

• Journal of the Korean Institute of Gas
• /
• v.28 no.2
• /
• pp.76-83
• /
• 2024

In the semiconductor manufacturing process, the Diffusion process generates various reactive by-products. These by-products are deposited inside the pipes of post-processing and exhaust treatment systems, posing a potential risk of substantial dust explosions. In this study, three methods material verification, selection of analysis samples, and risk analysis were employed to address the substances produced during the Diffusion process. Among the materials handled in the Diffusion process, ZrO₂, TEOD, and E-DEOS were identified as raw material capable of generating by-product dust. Test for Minimum Ignition Energy and dust explosion were conducted on the by-products collected from each processing facility. The results indicated that, in the case of MIE, none of the by-products ignited. However, the dust explosion test revealed that ZrO₂ exhibited a maximum pressure of 7.6 bar and K_st value of 73.3 bar·m/s, its explosive hazard. Consequently, to mitigate such risks in semiconductor processes, it is excessive buildup.