• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1998년도 춘계학술대회논문집; 용평리조트 타워콘도, 21-22 May 1998
• /
• pp.684-688
• /
• 1998

Optimization of the collocated piezoceramic sensor/actuator placement is investigated numerically and verified experimentally for vibration control of laminated composite plates. The finite element method is used for the analysis of dynamic characteristics of the laminated composite plates with the piezoceramic sensor/actuator. The structural damping index(SDI) is defined from the modal damping. It is chosen as the objective function for optimization. Weights for each vibrational mode are taken into account in the SDI calculation. The gradient method is used for the optimization. Optimum location of the piezoceramic sensor/actuator is determined by maximizing tie SDI. Numerical simulation and experimental results show that the optimum location of the piezoceramic sensor/actuator is dependent upon the outer layer fiber orientations of the plate, and location and size of the piezoceramic sensor/actuator.

• Wind and Structures
• /
• 제4권1호
• /
• pp.63-72
• /
• 2001

This paper presents results of a study on wind loads and wind induced dynamic response of bridge jointed twin-towered buildings. Utilizing the high-frequency force balance technique, the drag and moment coefficients measured in wind tunnel tests, and the maximum acceleration rms values on the top floor of towers, are analyzed to examine the influence of building's plan shapes and of intervals between towers. The alongwind, acrosswind and torsional modal force spectra are investigated for generic bridge jointed twin-towered building models which cover twin squares, twin rhombuses, twin triangles, twin triangles with sharp corners cut off, twin rectangles and individual rectangle with the same outline aspect ratio as the twin rectangles. The analysis of the statistical correlation among three components of the aerodynamic force corroborated that the correlation between acrosswind and torsional forces is significant for bridge jointed twin-towered buildings.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 D
• /
• pp.2389-2391
• /
• 2004

This paper is concerned with the active vibration control of plate system using electromagnetic force actuator. The transfer function from the force input to the bending displacement was obtained via modal analysis results. Control algorithm are proposed and implemented on the experimental setups to show their efficacy. In this paper, the genetic algorithm is used to design a $H_2$ controller. Effectiveness and performance of the designed controller were verified by simulation and experiment results.

• 대한기계학회논문집A
• /
• 제20권5호
• /
• pp.1498-1507
• /
• 1996

This paper presents a robust control of a smart flexible structure featured by a piezofilm actuator characterizing its light weght and quick response time. A mathematical governing equation for the proposed structure is derived by employing Hamilton's principle and a state space control model is subsequentrly obtained through modal analysis. Uncertain system parameters such as frequency variation are included in the control model. A sliding mode control theroy thich has inherent robustness to systme uncertainties is adopted to design a tracking controller for the peizofilm actuator. Using the output informaiton from the tip deflection sensor, a full-order observer is constructed ot estimate state variables for the system. Tracking performances for desired trajectories of sinusoidal amd step functions are evaluated by undertaking both simulation and experimental works.

• 대한기계학회논문집A
• /
• 제25권3호
• /
• pp.408-414
• /
• 2001

The structural characteristics of the stiffened double cylinder was investigated through experiment and analysis. The outside cylinder was excited with piezoelectric actuator and the mode shape of the cylinder with stiffening T frame was obtained by using holographic interferometry. Finite element method was applied for further modal investigation of the stiffened cylinder. The experimental results showed that the mode shape of cylinder was dependent on the exciting frequencies and the T frame showed salient effect of damping at most of the resonent frequencies. In particular frequencies, the T frame worked as a transmitter. FFM showed similar results with the experiments. This paper showed that the laser-based method such as holographic interferometry is well suited for investigation of the whole-field mode shapes and FEM has good performance to estimate the medal characteristics of the mechanical structure.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2006년도 정기 학술대회 논문집
• /
• pp.225-231
• /
• 2006

The purpose of this study is to develop a promising hybrid structural health monitoring system for structural joints. For this propose, the combined use of vibration-based techniques and electro-mechanical impedance technique is employed. For the verification of the proposed health monitoring scheme, a series of damage scenarios are designed to simulate various situations at which the connection joints can experience during their service life. The obtained experimental results, modal parameters and electro-magnetic impedance signatures, are carefully analyzed to recognize the connecting states and the target damage locations. From the analysis. it is shown that the proposed hybrid health monitoring system is successful for acquiring global and local damage information on the structural joints.

• 소음진동
• /
• 제8권4호
• /
• pp.643-653
• /
• 1998

The sub-resonance modes can be easily excited by the assembling tolerance in the asymmetric type optical pick-up actuators, compared with the symmetric type. In this paper, we propose the novel method for reducing the vibration due to the sub-resonance modes whose amplitude can be decreased by adding the damper and increasing the flexibility of holder PCB. Using the finite element method, the change of mode shapes is investigated as the shape of holder PCB is modified. Experimental results support that the propopsed method reduces remarkably the vibration of sub-resonance modes of the optical pick-up actuator.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.639-646
• /
• 2000

Estimation for the vibration behavior of a nuclear fuel rod with its supporting structure called spacer grid has been made by the both of experimental and analytical methods in order to compare the supporting performance of two kinds of the spacer grids which have been newly developed. For the analytical method the fuel rod was modeled as a beam continuously supported by the springs of the spacer grid, and ABAQUS computer code was utilized. After a modal testing was performed for the fuel rod supported by five spacer grids, two results has been compared to justify and compensate the both methods. It has been found that the spring design of the spacer grid could give significant effect to natural frequency and vibration amplitude of the fuel rod.

• International Journal of Precision Engineering and Manufacturing
• /
• 제1권2호
• /
• pp.67-75
• /
• 2000

virtual computer numerical control(VCNC) arises from the concept that one can experience pseudo-real machining with a computer-numerically-controlled(CNC) machine before actually cutting an object. To achieve accurate VCNC, it is important to determine abnormal behavior, such as chatter, before cutting. Detecting chatter requires an understanding of the dynamic cutting force model. In general, the cutting process is a closed loop system the consists of structural and cutting dynamic. Machining instability, namely chatter, results from the interaction between these two dynamics. Several previous reports have predicted stability for a single path, using a simple cutting force model without run out and penetration effects. This study considers both tool run out and penetration effects, using experimental modal analysis, to obtain predictions that are more accurate. The machining stability during a corner cut, which is a typical transient cut, was assessed from an evaluation of the cutting configurations at the corner.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.150-153
• /
• 2006

점탄성 복합재는 간단한 작업으로 큰 감쇠 효과를 볼 수 있어 사용이 날로 늘어나고 있다. 그런데 점탄성 복합재의 특성은 온도에 민감하게 반응하며 변화한다. 그러므로 점탄성 복합재의 모드해석 시 온도 변화에 따른 해석이 필요하다. 본 논문에서는 한쪽면에 점탄성재를 부착한 Oberst beam을 일단고정 상태로 설치하여 실험 온도를 $-15{\sim}45^{\circ}C$로 변화시켜가며 전달함수를 이용하여 실험모드해석을 실행하였다. 그리고 온도 차이에 따른 모드형상을 비교하였다.