• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.06a
• /
• pp.141-146
• /
• 1999

An experimental investigation on the leakage characteristics of a labyrinth seal, high-low seal, is studied. Pressure distribution and leakage flow rate are measured along with the shaft speed and the pressure difference between the entrance and the exit. Pressure distribution vanes almost linearly along the seal and the leakage flow rate increases as the increase of the pressure difference. Furthermore, it is found that both the shaft speed and the shaft vibration have no influence on the leakage of the labyrinth seal.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.75-75
• /
• 2012

This presentation will focus on computational materials research carried out across length scales. Examples will be presented that illustrate the way in which state-of-the-art quantum mechanical calculations and atomistic simulations can be applied to explain experimental data, design new structures, determine mechanisms, and enable new investigations. In particular, the presentation will present key findings from an integrated experimental and computational investigation of the tribological properties of polytetrafluoroethylene and its composites and predictions regarding the mechanical and tribological properties of inorganic nanostructured materials.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10a
• /
• pp.495-500
• /
• 1998

This paper describes an experimental investigation on the effect of concrete strength on tension stiffening behavior. Total ten direct tension specimens were tested with concrete compressive strength range up to 900kg/$\textrm{cm}^2$. From the experimental program, it was observed that higher strength concrete specimens provides smaller crack spacings and less stiffening effect.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.377-380
• /
• 1999

This paper dscribes an experimental investigation into the cause of flexural-shear failure in RC beams. The experimental variables are bottom flange width and tension bar location. Then these test results were compared and analyzed to deduce the major cause of critical-shear cracking. As a result, it was found that the propagation of the critical shear crack depended exclusively on the intensity of horizontal cracking.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.05a
• /
• pp.54-59
• /
• 2001

This paper presents an analytical investigation pertaining to the elastic buckling behavior of pultruded fiber reinforced plastic equal-leg angle members under concentric axial compression. The elastic local and global buckling (flexural, torsional, and flexural-torsional) analyses are conducted, respectively, and the analytical results are compared with the existing experimental results. The differences were more than 10%, and the experimental results were higher than the analytical results.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.5
• /
• pp.666-674
• /
• 2003

An experimental investigation was performed to study the characteristics of turbulent swirling flow in an axisymmetric annuli. The swirl angle measurements were performed by flow visualization technique using smoke and dye liquid along the test tube. Using the Particle Image Velocimetry method, this study found the time-mean velocity distribution and turbulent intensity with swirl for Re = 20.000. 30.000, 50.000. and 70.000 along longitudinal sections and the results appear to be physically reasonable.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.2
• /
• pp.105-113
• /
• 2000

For exact spherical involute bevel gear, serveral researchers had developed the mathematical models. The solid models of straight bevel gears are obtained and inspected to avoid interference by computer graphics. Furthermore, A gearbox is assembled by spherical involute bevel gears, which are manufactured by CNC machine. The transmission errors in the tooth mesh are measured by Laser sensor, are compared with the AGMA standard. This gearbox is found to be ranked AGMA Q10(JIS 3)

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.708-711
• /
• 2004

A typical structure was selected for a prototype and four 1:2.5 scaled models, representing the subassemblage including the interior column and the deep beam, were constructed. The transverse reinforcement was designed according to ACI procedure and the procedure proposed by Sheikh. In this study, the correlation between the experimental and analytical responses of the subassemblages subjected to the cyclic lateral displacement were evaluated through investigation of lateral load-lateral deformation, local deformation characteristics by using a nonlinear FEM analysis program RCAHEST.

• Journal of Pharmaceutical Investigation
• /
• v.24 no.3
• /
• pp.67-77
• /
• 1994

The RMS statistical approach has demonstrated its potential in developing pharmaceutical dosage forms and in improving tabletting performance. Using an optimized formula, the tabletting performances of vitamin C-90 such as compressibility, disintegration time, lubrication and friability are significantly enhanced when compared with the performance of a traditional test formula. More important, this method also enables us to serve our customers better. Any customized modification of a suggested formula or any technical problem related performance etc. can be readily resolved by simple examination of the models.

• Tribology and Lubricants
• /
• v.11 no.1
• /
• pp.44-49
• /
• 1995

Friction characteristic of an engine crankshaft bearing is affected by revolution speed, applied loads, and viscosity of lubrication. So, experimental investigation is required to observe the friction characteristics using these factors. Hydraulic cylinder, servo controller system which can be modified the applied load, and test rig for the observation of the characteristics of engine crankshaft bearings were designed and fabricated, and some experiments were performed. Friction torque, journal locus and circumferential temperature variation of crankshaft bearing were measured according to applied load, revolution speed, and oil inlet temperature.