• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.82-87
• /
• 1996

To find the effects of pressure on critical heat flux (CHF) for the conditions of low pressures (especially up to 10 bar) and low mass flux (~300 kg/$m^2$s), a series of experiments have been accomplished by using uniformly heated Inconel-625 tube. The experimental ranges are as follows: pressure (from 1.2 to 8 bar). mass velocities (from 100 to 250 kg/$m^2$s) and the inlet subcooling ($\Delta$h$_{i}$ ＝ 350 kJ/kg). According to the experimental data, it is found that the CHF is nearly independent of the pressure and increases with mass flux. From the results of the CHF correlation assessment for this experimental data, we could find somewhat different tendency of CHF behavior from every other CHF prediction correlation and table.ation and table.

• Journal of Power Electronics
• /
• v.9 no.2
• /
• pp.207-214
• /
• 2009

This paper presents a modem approach for speed control of a PMSM using the Particle Swarm Optimization (PSO) algorithm to optimize the parameters of the PI-Controller. The overall system simulated under various operating conditions and an experimental setup is prepared. The use of PSO as an optimization algorithm makes the drive robust, with faster dynamic response, higher accuracy and insensitive to load variation. Comparison between different controllers is achieved, using a PI controller which is tuned by two methods, firstly manually and secondly using the PSO technique. The system is tested under variable operating conditions. Implementation of the experimental setup is done. The simulation results show good dynamic response with fast recovery time and good agreement with experimental controller.

• Journal of Pharmaceutical Investigation
• /
• v.9 no.1
• /
• pp.1-6
• /
• 1979

This report is carried out pharmaceutical properties for the mosquito coil made of Ginseng leaf and the residue after extraction of Ginseng root. This experimental results are: Loss on drying of Insam (Ginseng) mosquito coil powder is average 8.31%, ash content of the powder is average 9.51% and burning time of Insam mosquito coil is aprroximately 36 minutes per gram. The contents of carbon monoxide and carbon dioxide on burning of mosquito coil are as same as following: Insam mosquito coil A brand mosquito coil B brand mosquito coil Allethrin in a piece of Insam mosquito coil was stable under the experimental conditions. CO (ppm) 360 540 760 $CO_2(%)$ 0.052 0.076 0.066 Allethrin in a piece of Insam mosquito coil was stable under the experimental conditions.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.225-229
• /
• 2000

Burrs formed during face milling operations are very hard to characterize like other machining burrs because there are many parameters which affect the cutting process. Many researchers have tried to predict burr characteristics including burr size and shapes with various experimental conditions such as cutting speed, feed rate, in-plane exit angle, number of inserts, etc., but it still remains as a challenging problem for the complicated combination effects between the parameters. In this paper, Taguchi method, which is a systematic optimization application of design and analysis of experiments, is introduced to acquire optimum cutting parameters for burr minimization. Optimized experimental conditions are provided to show the effectiveness of this approach.

• KSTLE International Journal
• /
• v.1 no.1
• /
• pp.59-62
• /
• 2000

This paper deals with an experimental study on the dynamic response of an elastomeric oil seal when the interferences between shaft and lip as well as the dynamic eccentricities are present. The dynamic response of seal lip in oil seals was observed with the aid of an image processing apparatus. The temperature of the seal lip edge, friction torque and the dynamic sealing gap between shaft and lip are measured at different conditions of the initial interference and the shaft eccentricity, The data were simultaneously measured under dynamic conditions. Experimental results show that, as the shaft speed is increased, S/e$_{d}$ has nearly reached a constant asymptotic value fur a certain range of shaft speeds. The results indicate that the gap separation between shaft and lip is provided due to the shaft eccentricity because the seal lip cannot follow quickly the radial displacements with increasing shaft speed.d.

• Mass Spectrometry Letters
• /
• v.3 no.4
• /
• pp.108-111
• /
• 2012

An experimental study on the nascent product of the OH heterogeneous reaction with NaCl was performed under dry and wet conditions using a bead-filled flow tube system coupled to a high-pressure chemical ionization mass spectrometer. The ozone concentration in the flow tube for the atomic hydrogen removal was varied in order to control the conversion reaction of molecular chlorine into HCl for the identification of the nascent product. The mass spectrometric observation was that the $O_3$ introduction reduced the concentration HCl, while it increased the concentration of $Cl_2$ and ClO. Based on the experimental results, we suggest that the nascent product of the titled reaction is gaseous $Cl_2$, which is followed by fast conversion into HCl in presence of H. No significant difference in the concentration profile between under dry and wet (RH = 2%) conditions was observed.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.1 no.2
• /
• pp.123-130
• /
• 1997

The effect of experimental factors on the Freeze-Thaw durability in the High Strength Concrete has been analyzed and investigated with [DESIGN of EXPERIMENT: L16). The Experimental parameters included the type of aggregate and mixer, the conditions of aggregates, and the difference of mixing temperature, procedure and placing, etc. It is aim of this study to provide the fundamental data on the effect of various factors on the frost resistance of high strength concrete for the practical use and research data accumulation of durability inspection. The results of this experiment indicate that the freeze-thaw durability of high strength concrete is markedly affected by the coarse aggregate source, mixing temperature and curing conditions.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.309-314
• /
• 2004

The experimental loop was designed and installed to measure the disc positions, disc back stop load and differential pressure with flow velocity for 3 inch and 6 inch swing check valves. The tests were performed at various conditions of upstream flow disturbance source and distance from the tested check valves to investigate the effect of the upstream flow conditions on the disc stability of the swing check valves. The selected disturbance sources were elbow, globe valve, and orifice. The experimental results are presented herein.

• Journal of the Korean Chemical Society
• /
• v.58 no.1
• /
• pp.80-84
• /
• 2014

The process of petroleum involves in a large amount of oily wastewater that contains high levels of chemical oxygen demand (COD) and toxic compounds. So they must be treated before their discharge into the receptor medium. In this paper, wet peroxide oxidation (WPO) was adopted to treat the oily wastewater. Central composite design, an experimental design for response surface methodology (RSM), was used to create a set of 31 experimental runs needed for optimizing of the operating conditions. Quadratic regression models with estimated coefficients were developed to describe the COD removals. The experimental results show that WPO could effectively reduce COD by 96.8% at the optimum conditions of temperature $290^{\circ}C$, $H_2O_2$ excess (HE) 0.8, the initial concentration of oily wastewater 3855 mg/L and reaction time 9 min. RSM could be effectively adopted to optimize the operating multifactors in complex WPO process.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.9
• /
• pp.1493-1498
• /
• 2007

In this work, alkyl methacrylate-based microgels were synthesized by an experimental design method, and their sebum absorption characteristics were investigated. The results of fractional factorial experimentation indicated that the cross-linking agent content, solvent content, and stirring speed were the main parameters in the synthesis of the microgels. The suitable synthesis conditions were determined by the response surface design method. Through a study of the monomer and solvent effects, it was confirmed that the microgel shows the highest sebum absorption ratio when t-butyl methacrylate is used as a monomer or when acetone is used as a solvent. The optimal microgel synthesis conditions for cosmetic application were determined, and the resulting microgel had a mean particle size of 4.7 μm and a sebum absorption ratio of 435%.