• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.951-956
• /
• 2008

The study is to develop a foundation design for a railway vehicle simulator using a scaled model. Although a scaled simulator is limited to manipulate the dynamics of a full-size railway vehicle, it has been known to have an advantage, since a scaled model could provide the fundamental dynamic behavior within a limited space of a laboratory facility and with a low operation cost while an experiment is conducted. This study is to propose a design strategy for a simulator so that a small scaled roller rig could be fabricated in a laboratory based on the design philosophy. The data obtained from the scale model is also experimentally investigated in conjunction with appropriate non-dimensional analysis so that the output results should be interpreted to the railway vehicle.

• Ocean and Polar Research
• /
• v.26 no.2
• /
• pp.333-339
• /
• 2004

This paper is concerned with an experimental investigation about tractive performance of a tracked vehicle on extremely soft soil. A tracked vehicle model with principal dimensions of $0.9\;m(L)\;{\times}\;0.75\;m(B)\;{\times}\;0.4\;m(H)$ and the weight of 167 kg was constructed with a pair of driving chain links driven by two AC-servo motors. The tracks are configured with detachable grousers with variable span. Deep seabed was simulated by means of bentonite-water mixture in a soil bin of $6.0\;m(L)\;{\times}\;3.7\;m(B)\;{\times}\;0.7\;m(H)$. Slip of vehicle and driving torque of motor were measured with respect to experimental variables; grouser span, grouser chevron angle, driving speed, drawbar-pull weight, position of center-of-gravity and weight. $L_8$ orthogonal array is adopted for DOE (Design Of Experiment). The effects of experiment variables on traction performance are evaluated.

• Nuclear Engineering and Technology
• /
• v.39 no.4
• /
• pp.327-336
• /
• 2007

The influence of density differences on the mixing of the primary loop inventory and the Emergency Core Cooling (ECC) water in the downcomer of a Pressurised Water Reactor (PWR) was analyzed at the ROssendorf COolant Mixing (ROCOM) test facility. ROCOM is a 1:5 scaled model of a German PWR, and has been designed for coolant mixing studies. It is equipped with advanced instrumentation, which delivers high-resolution information for temperature or boron concentration fields. This paper presents a ROCOM experiment in which water with higher density was injected into a cold leg of the reactor model. Wire-mesh sensors measuring the tracer concentration were installed in the cold leg and upper and lower part of the downcomer. The experiment was run with 5% of the design flow rate in one loop and 10% density difference between the ECC and loop water especially for the validation of the Computational Fluid Dynamics (CFD) software ANSYS CFX. A mesh with two million control volumes was used for the calculations. The effects of turbulence on the mean flow were modelled with a Reynolds stress turbulence model. The results of the experiment and of the numerical calculations show that mixing is dominated by buoyancy effects: At higher mass flow rates (close to nominal conditions) the injected slug propagates in the circumferential direction around the core barrel. Buoyancy effects reduce this circumferential propagation. Therefore, density effects play an important role during natural convection with ECC injection in PWRs. ANSYS CFX was able to predict the observed flow patterns and mixing phenomena quite well.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.12
• /
• pp.55-67
• /
• 2010

The electrical properties of a back drilled via-hole (BDH) without the open-stub and the plated through via-hole (PTH) with the open-stub, which is called the conventional structure, in a high-count multi~layered (HCML) printed circuit board (PCB) were investigated for a high-speed digital system, and a selected inner layer to transmit a high-speed signal was farthest away from the side to mount the component. Within 10 GHz of the broadband frequency, a design of experiment (DOE) methodology was carried out with three cause factors of each via-hole structure, which were the distance between the via-holes, the dimensions of drilling pad and the anti-pad in the ground plane, and then the relation between cause and result factors which were the maximum return loss, the half-power frequency, and the minimum insertion loss was analyzed. Subsequently, the empirical formulae resulting in a macro model were extracted and compared with the experiment results. Even, out of the cause range, the calculated results obtained from the macro model can be also matched with the measured results within 5 % of the error.

• Journal of Korean Institute of Industrial Engineers
• /
• v.31 no.4
• /
• pp.334-340
• /
• 2005

A mouse is an important input device that is used in most of all computer works. A mouse control time prediction model was proposed in this study. Especially, the model described the time of mouse control that made a cursor to move within path constraints. The model was developed by a laboratory experiment. Cursor movement times were measured in 36 task conditions; 3 levels of path length, 3 levels of path width and 4 levels of target's width. 12 subjects participated in all conditions. The time of cursor movement with path constraints could be better explained by the combination of Fitts' law with steering law($r^2=0.947$) than by the other models; Fitts' law($r^2=0.740$), Steering law($r^2=0.633$) and Crossman's model($r^2=0.897$). The proposed model is expected to be used in menu design or computer game design.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.5
• /
• pp.277-282
• /
• 2004

The optimal design of the rotor slot for inverter-fed induction motor was performed. The purpose of the paper is to verify the optimal point by experiment. A sensitivity analysis is performed, and the models near to an optimal point are selected. In the selecting process of models, 2 design variables with high sensitivity are selected out of 5 design variables. On the basis of the selected variables, 2 models near to the optimal point are decided. The tim e-step F.E.A and the experiment are performed. Optimal point and performance improvement of the optimal mode are verified.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.12
• /
• pp.93-100
• /
• 2013

This paper propose a method to design the rotor of synchronous reluctance motors(SynRM) for maximum torque and power factor by using DOE(design of experiment) with the design variables which are parameters of barriers and segments. In this process, there are problems that require lots of simulation time and number of simulations when calculating the both torque and power factor using the finite element method in order to find load angle, core loss per speed. In order to improve this problem, we calculate only value of flux linkage by finite element method, and can decrease analysis and the number of analysis time by applying steady state expression of the power factor and torque. Finally, in order to verify the characteristics of optimal model, we make prototype motor and compare with the conventional SynRM. In this experiment, we use the DC current decay test for calculating d-and q-axis inductance.

• Transactions of Materials Processing
• /
• v.9 no.5
• /
• pp.512-525
• /
• 2000

Designers are frequently faced with multiple quality issues in injection molded parts. These issues are usually In conflict with each other, and thus tradeoff needs to be made to reach a final compromised solutions. The objective of this study is to develop an automated injection molding design methodology, whereby part defects such as warpage and weld line are optimized. The features of the proposed methodology are as follows: first, Utility Function approach is applied to transform the original multiple objective problem into single objective problem. Second is an implementation of a direct search-based Injection molding optimization procedure with automated consideration of process variation. The Space Reduction Method based on Taguchi's DOE(Design Of Experiment) is used as a general optimization tool in this study. The computational experimental verification of the methodology was partially carried out for a can model of Cavallero Plastics Incorporation, U. S. A. Applied to production, this study will be of immense value to companies in reducing the product development time and enhancing the product quality.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.3
• /
• pp.147-154
• /
• 2004

This paper presents a procedure for analysis and design of a fine positioning stage, which has many applications in industries for machine tools, semiconductor, LCD and so forth. The stage considered here is based on a single module with 3 axes which is composed of flexures hinges, piezoelectric actuators and their peripherals. Through a series of analysis, the structural analysis model is simplified as a rigid body(the moving part) and springs(the flexures hinges). An experimental design procedure is applied to determine the dimension of flexures hinges. A sensitivity analysis on the notch positions is also performed to obtain a guideline of fabrication accuracy for the stage. An actual fine stage is made and verified through an experiment on the dynamic characteristics.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.6
• /
• pp.556-565
• /
• 2004

We have experimented an actual solar water heating system acquiring real data for one year period. On the basis of the operation data, it is necessary to predict the system performance such as collector efficiency and solar fraction, and to analyze the economical efficiency for system optimal design. To estimate the performance of actual systems through simulation, valid modelling for components consisting of the system should be accompanied. The present study is focused on the modelling for load patterns and operating control conditions. We proposed two load models: concentration model which gathers real loads as a meaningful group and distribution model which disperses real loads with time. If grouping of the load distribution is suitable, the predicted values by the concentration model approaches to those by the distribution model close to actual load pattern apparently. As a result, both of them are in good agreement with those by experiment.