• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.9
• /
• pp.10-19
• /
• 1999

In this study , a simple method has been developed to detect the required spark voltage by using the primary spark voltage instead of the secondary spark voltage. Through engine motoring experiments, this method testified to be quite satisfactory. Though the required spark voltage is affected by many in-cylinder conditions, temperature is one of the most important factors. The temperature increases significantly by combustion and the required spark voltage also changes by the temperature during the expansion stroke. On the basis of this fact, misfire can be monitored by comparing the required spark voltage between compression stroke and expansion stroke. So, in this study, two step ignition method is introduced to monitor combustion at expansion stroke. The test result shows that this method can be used to detect complex misfire pattern.

• Journal of KSNVE
• /
• v.8 no.4
• /
• pp.654-662
• /
• 1998

To predict the radiating noise from the vibrating surface, it is required to know the velocity distribution of vibrating surface exactly as possible as it can. Although it can be obtained by finite element method, their accuracy is limited by theuncertainty of preparing input data such as material propoerties, damping, excitation, and the actual boundary conditions. Experimental values are accurate but are seldom available as many asthe data points compared to FEM mesh. Therefore, hybrid method of experiment and finite element method, called modal expansion technique, is investigated for the preparatin of accurate element method at specified frequencies and for the verification of this scheme, related experiment is performed. In high frequency range above 2000 Hz, piezo-electric material is used as an actuator.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.966-972
• /
• 2014

The Lattice Boltzmann Method (LBM) has attracted attention as an alternative numerical algorithm for solving fluid mechanics, and its intrinsic unsteadiness and weak numerical damping make it more suitable for aeroacoustic problems. In this paper, applicability of the LBM for solving flow noise problems is tested by applying it to predict transmission loss of a simple expansion silencer. The time history of the static pressure is recorded at the inlet and outlet pipes. The transmission loss (TL) of the muffler is computed by using three point method and two source method, respectively. The TL calculated using the LBM is compared with that computed using finite element method (FEM) and measured data. It is found through these comparisons that the LBM is capable of predicting TL of the simple expansion silencer accurately, which it is difficult to predict using the conventional CFD methods based on the RANS solvers.

• Transactions of Materials Processing
• /
• v.31 no.1
• /
• pp.23-28
• /
• 2022

Although the hole expansion test is currently the most commonly used method to evaluate the stretch flangeability of HSS, it has been criticized due to its poor repeatability and reproducibility for test results. This paper focuses on the development of a new measurement method to investigate the stretch flangeability of HSS. Two materials (DP590, DP980) were investigated with a hole expansion test and a developed test method. Test results showed that the developed test method could be used as one stretch flangeability test to help identify relevant parameters of the shearing process to avoid edge cracking.

• Journal of the Korean Society of Physical Medicine
• /
• v.9 no.1
• /
• pp.11-23
• /
• 2014

PURPOSE: The purpose of this study suggests the exercise programs for improving the function and structure by applying the Schroth exercise method and sling exercise method to the scoliosis patient. METHODS: The subjects were 16 patients who were diagnosed with scoliosis. They were randomly assigned either to a Schroth exercise group (n=8) that received Schroth exercise program or to a sling exercise group (n=8) that received sling exercise program. Flexibility, static balance, dynamic balance, and spinal angles were measured by using the modified sit and reach test, one leg standing with closed eyes, functional reach test, and Cobb's angle, respectively. The chest expansion were calculated using differences of chest circumference between maximum inspiration and maximum expiration measured under armpits, at the junction between the sternum and xiphoid process, and at the waist. RESULT: Schroth group before and after the intervention there was a difference in the static balance, spine angle, chest expansion (p<.05). sling group before and after the intervention there was a difference in the flexibility, static balance, spine angle, chest expansion (p<.05). There were significantly differences between the both groups for chest expansion thoracic level inspiratory variables at post-exercise. CONCLUSION: These results revealed that two exercise program improved flexibility, static standing balance, spine angle, chest expansion level and ability used as scoliosis management and intervention. Therefore, it is expected to be used as a method for the treatment and prevention in the process of rehabilitation of patients with scoliosis.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1344-1346
• /
• 1995

The interrupting capability of gas circuit breakers(GCB) are critically dependent on the pressure rise of the puffer cylinder or the thermal expansion chamber at current zero. Therefore it's very useful for the designers to know the pressure rise there at the design stage. Much effort has been done to predict the pressure rise in the puffer cylinder or the thermal expansion chamber in no-load condition. Thus, we now calculate it with reasonable accuracy with the simple programs coded by ourselves or with the commercial CFD packages. However, it has been still difficult problem to calculate it under the existence of arc. In this paper, we propose a method which can be used to predict the pressure rise in the thermal expansion chamber of thermal expansion type GCB. The method has been applied to the 25.8kV 25kA thermal expansion type model GCB and the calculated results have been compared with those from experiment.

• Journal of Korean Society of Rural Planning
• /
• v.10 no.4 s.25
• /
• pp.9-18
• /
• 2004

The purpose or this study is to simulate spatially the urban expansion phenomena with a cellular automata (CA) technique using GIS. A study area, Suwon city, was selected for test of model verification and application with the classified land-use maps of three data years: 1986, 1996, and 2000. The urbanized potential maps were generated with seven criteria of one geographic factor (slope of land), and six accessibility factors (time distances from city, national road, Seoul, station, and built-up boundary), considering their weighting values, which were optimized by WSM (weighted scenario method for intensity order) combined a ranking method and a AHP technique. The optimized weighting values at the urban expansion between 1986 and 1996 were applied to verify the CA model for the other expansion between 1996 and 2000. The results of model application showed that urban sprawl phenomena of the urban expansion toward rural area can be simulated spatially and temporally with several boundary conditions considering various scenarios for the criteria and parameters of the model. Ultimately, this study can contribute to reference data for land-use planning of urban fringe areas.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.8
• /
• pp.744-749
• /
• 2011

In this study, determination method of initial optimal nozzle expansion in pintle rocket was investigated. The initial optimal initial nozzle expansion was decided by maximizing the mass-averaged thrust coefficient that is calculated from thrust coefficient of minimum and maximum chamber pressure. The determination of initial optimal initial nozzle expansion was equivalent to that of the minimum propellant mass which was required for obtaining the desired mission performance. The highest pressure, thrust turndown ratio and total impulse ratio effected on the initial optimal nozzle expansion. Among them, total impulse ratio had great influence on the initial optimal nozzle expansion.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.1 s.232
• /
• pp.156-162
• /
• 2005

Stouts are frequently used throughout the human body, but the most critical areas are in coronary arteries. They open pathways in vessels and supply blood directly to the heart muscle. To simulate behavior of expansion for the coronary stent by balloon, the commercial finite element code LS-DYNA and ANSYS were used in the analysis. The explicit method is used to analyze the expansion of the stent and the implicit method is performed to simulate the springback that developed in a stent after the balloon pressure has been removed. Finally the experimental results for the expansion of the PS153 stents were compared with the FEM results. The springback was measured with the stents subjected to no external pressure to which stents are subjected in vivo. The simulated results were in good agreement with experimental results. Standard mechanical characteristics such as stress, plastic strains, and springback can be derived from the numerical results. These data can be used to determine maximum expansion diameter without fracture and expansion pressure considering elastic recoil.

• The korean journal of orthodontics
• /
• v.49 no.3
• /
• pp.150-160
• /
• 2019

Objective: This study aimed to analyze the effect of changing various parameters of the bone-borne rapid palatal expander (RPE) using the finite element method (FEM). Methods: In eight experimental groups, we investigated the effect of the number, position, and length of miniscrews; positional changes of the expander; and changes in the hook length on maxillary expansion. In finite element analysis, we compared the magnitude and distribution of stress, and the displacement changes following expansion of the bone-borne RPE. Results: When we compared the number and position of miniscrews, placing miniscrews in the anterior and posterior sides was advantageous for maxillary expansion in terms of stress distribution and displacement changes. Miniscrew length did not significantly affect stress distribution and displacement changes. Furthermore, anteroposterior displacement of the expander did not significantly affect transverse maxillary expansion but had various effects on vertical changes of the maxilla. The maxilla rotated clockwise when the miniscrews were placed in the anterior region. The hook length of the expander did not show consistent results in terms of changes in stress distribution and magnitude or in displacement changes. Conclusions: The findings of this study suggest that changes in the location and length of the miniscrews and displacement of the bone-borne RPE could affect the pattern of the maxillary expansion, depending on the combination of these factors.