• 한국가스학회지
• /
• 제12권4호
• /
• pp.21-28
• /
• 2008

삼지화염과 포와젤(Poiseuille) 및 균일분포 연료출구 속도에 따른 부상화염의 부상거동 그리고 화염면 부근에서의 연소 유동 특성에 대하여 수치적 해석을 수행하였다. 부상화염에 대한 수치해석으로 기존 연구 결과를 검정하고 화염대 부근에서 구조적 특성을 살펴보며 포와젤 및 균일분포 연료출구속도 조건에서 운동량 유속으로 부상높이를 일반화하여 비교하였다. 또한 화염면 부근에서 속도, 압력, 온도, 화학반응속도 등으로 연소 유동 특성을 분석하고 규명하였다. 특히 중심선을 따른 속도 변화의 경우 노즐에서 화염대 부근까지는 전형적인 비반응제트 유동에 따른 속도 분포를 형성하지만 화염대 직전에서 속도가 급격히 감소하다가 화염대를 지나면서 급격히 증가한 후에 다시 감소하는 현상을 규명하였다. 화염대 전의 유동영역에서는 화염대가 장애물역할을 하다가 화염대를 지나고 나면 유동을 가속시켜주는 역할을 하고 있기 때문이다. 이러한 현상은 기존의 비반응 제트 유동으로 규명하지 못하였던 것이다.

• 한국가스학회지
• /
• 제16권1호
• /
• pp.1-7
• /
• 2012

복합 화력발전소 배열회수보일러에서의 입구 덕트 확관 형상 변화에 따른 전열관군 전단에서의 유동 균일화 특성을 유동수치해석을 통하여 분석하였다. 배열회수보일러의 입구는 가스터빈 후류의 출구에 해당하고 가스터빈 후류는 강한 선회 및 난류 유동이다. 본 연구에서 배열회수 보일러 입구 유동 경계조건은 가스터빈을 통과한 출구 유동 해석 결과를 이용하여 수행하였다. 배열회수보일러의 전열관군 전단에서의 유동 균일화 특성이 배열회수 보일러의 효율에 직결되므로 입구 덕트 확관 변곡점의 위치 변화에 따라 유동 균일화 특성을 파악함으로써 배열회수 보일러의 형상 최적화의 기반을 마련하는 것을 목적으로 하였다. 본 연구로부터 배열회수 보일러 확관의 변곡점의 위치가 기준 형상에서 낮은 위치에서 전열관군 전단에서 최적의 유동 균일화가 이루어짐을 알았다.

• 한국항공우주학회지
• /
• 제37권9호
• /
• pp.906-915
• /
• 2009

일반적으로 노즐 출구 부근에서 준연속체 상태로 방출된 추력기 플룸 유동은 노즐출구에서 멀어질수록 천이영역을 거쳐 자유분자 영역에 도달하기 때문에 진공영역에서의 추력기 플룸 영향을 연구하기 위해서는 광범위한 유동영역의 모델링이 가능한 직접모사법(DSMC)이 주로 사용된다. 본 논문에서는 진공영역에서 소형 단일추진제 추력기의 플룸 거동을 직접모사법을 이용해 수치적으로 예측하는 것이 목적이다. 정확한 결과를 효율적으로 유추하기 위해 예조건화 기법을 노즐 내부 연속체 영역의 해석에 도입하였으며, 이로부터 얻은 노즐 출구의 물성치 결과들을 직접모사법의 유입조건으로 적용하였다. 이렇게 두 기법을 결합하여 사용한 결과, 노즐 출구 부근에서 발생되는 강한 비평형성 및 넓은 후방유동 영역 등과 같이 진공영역에서 플룸이 가지는 고유의 특성들을 확인할 수 있었다.

• 대한기계학회논문집B
• /
• 제21권10호
• /
• pp.1350-1362
• /
• 1997

An experimental study has been performed on vortex pairing under fundamental and subharmonic forcing with controlled initial phase differences through hot-wire measurements and a multi-smoke wire flow visualization. For the range of St$_{D}$ < 0.6, vortex pairing was controlled by means of fundamental and subharmonic forcing with varying initial phase differences. Much larger mixing rate was achieved by two-frequency forcing with a proper phase difference than one frequency forcing. As St$_{D}$ decreased, vortex pairing was limited to a narrow region of the initial phase difference between two disturbances and higher amplitudes of the fundamental and its subharmonic at the nozzle exit were required for more stable pairing. As the amplitude of the subharmonic at the nozzle exit increased for fixed St$_{D}$ and fundamental amplitude, the distribution of the subharmonic mode against the variation of the initial phase difference changed from a sine function form into a cusp-like form. Thus, vortex pairing can be controlled more precisely for the former case. For St$_{D}$ > 0.6, non-pairing advection of vortices due to the improper phase difference was sometimes observed in several fundamental forcing amplitudes when only the fundamental was applied. However, when its subharmonic was added, vortex pairing readily occurred. As the initial amplitude of this subharmonic increased, the position of vortex pairing moved upstream. This was thought to be due to the fact that the variation of the initial phase difference between the fundamental and its subharmonic has less effects on vortex pairing in the region of fundamental-only vortex pairing.pairing.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제24회 춘계학술대회논문집
• /
• pp.329-333
• /
• 2005

고속의 자유 제트 및 표면 충돌시 나타나는 벽제트 내에서의 총온도 분포가 측정되어졌다. 자유제트에서는 노즐 출구로부터 측정거리를 달리하며(Z/D=1,2,4,6) 외기를 포함하여 총온도 분포가 측정되었으며, 제트와 외기간 전단층에서의 에너지 분리현상을 확인하였다. 벽제트 영역에서는 충돌거리가 짧은 경우에 대하여 반경위치를 달리하며(R/D=1.25, 1.5, 1.75, 2.0) 총온도 분포를 측정하여 벽제트 경계 및 벽근방에서의 에너지 분리현상을 확인하였으며, 단열벽면온도 분포와 이를 비교$\cdot$검토하여 설명하였다.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 1998년도 유체기계 연구개발 발표회 논문집
• /
• pp.217-222
• /
• 1998

CSCM upwind flux difference splitting compressible Navier-Stokes method has been used to predict the transonic flows in centrifugal compressor diffuser. The modified cyclic TDMA and the mass flux boundary conditions were used as boundary conditions of the diffuser analysis. With the mass flux boundary condition and the $130{\times}80{\times}40$ grid, the compressible upwind Navier-Stokes method predicted the transonic diffuser flowfield successfully. Plow changes in the impeller exit region due to the strong interaction between impeller exit and vaned diffuser, broad flow separation on the suction surface near hub and shroud was observed from the results of the mass flow rates 6.0 and 6.2kg/s at 27000 rpm. The static pressure increased and the total pressure decreased through the flow passage of the channel diffuser, which were predicted better from the three-dimensional analysis than from the two-dimensional analysis due to the strong effect of the three-dimensional flow. The mass averaged loss coefficients and pressure coefficients were also studied.

• 한국도로학회논문집
• /
• 제20권2호
• /
• pp.67-74
• /
• 2018

PURPOSES : The goal of this study is the development of roundabout accident models for urban and non-urban areas. METHODS : This study performed a comparative analysis of the regional factors affecting accidents. Traffic accident data were collected for the period 2010~2014 from the TAAS data set of the Road Traffic Authority. To develop the roundabout accident models, the Poisson and negative binomial regression models were used. A total of 25 explanatory variables such as geometry, and traffic volume were used. RESULTS : The key findings are as follows: First, it was found that the null hypotheses that the number of accidents is the same should be rejected. Second, three Poisson regression accident models, which are statistically significant (${\rho}^2$ of 0.154 and 0.385) were developed. Third, it was noted that although the common variable of the three models (models I~III) is the number of entry lanes, the specific variables are entry lane width, roundabout sign, number of circulatory roadways, splitter island, number of exit lanes, exit lane width, number of approach roads, and truck apron. CONCLUSIONS : The results of this study can provide suggestive countermeasures for decreasing the number of roundabout accidents.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.525-528
• /
• 2002

The objective of this study is to investigate characteristics of flow by the Rod shape and the choice of the turbulent intensity enhancement section. The Rod was setup vertically to the way of a nozzle exit flow and nozzle diameter is 17mm. Rod height is 5mm and its shapes are square, triangle, and circle. Characteristics of fluid such as velocity vector distribution, kinetic energy, turbulent intensity, and etc. were visualized, observed, and considered at 3 kinds of Re No. such as 2000, 3000, and 4000. The characteristics of flow field were investigated in each case of the distance rate from the nozzle exit to impinging plate(H/B=8, 10). The temperature of water is $20^{\circ}E$ and the measurement region divided by 3 sections(I, II, III). The nozzle diameter is 17mm. As the experimental result by PIV measurement, scale of the vector profile showed a tendency to an unbalance parabola distribution as increasing of the Re No. When the impinging plates such as square, triangle, and circle shape are installed respectively in front of the flow accelerated, rod shape of the highest velocity vector is circle shape and rod shape of the highest turbulent Intensity is square shape.

• 한국기계가공학회지
• /
• 제16권4호
• /
• pp.16-23
• /
• 2017

CFRP(Carbon Fiber Reinforced Plastics) has many industrial applications due to its low weight and high strength properties. Due to its superior properties, for example, excellent resistance to fatigue wear, corrosion, and breakage from fatigue, it has been widely applicable to aircraft, automotive, and medical industries and so on. The main machining for CFRP is drilling, and route milling. In case of drilling, the machining defects such as the delamination of each layer, uncut fiber, resin burning, spalling, and exit burrs are inevitable. The issue to remove such kind of defects is necessary to make CFRP parts successful. From this point of view, this paper investigates the removal effectiveness of machining defects existing at exit region with different type of tool geometries. Consequently, based on the experiments, the tool geometry is most impact factor to remove uncut fiber or resin.

• 대한기계학회논문집B
• /
• 제31권3호
• /
• pp.306-312
• /
• 2007

This paper describes the flow characteristics of circular multiple jet investigated by hot-wire anemometry. The nozzle arrays were classified into two cases; 6- or 7-nozzle located circumferentially in equal interval without or with a central jet. The flow field was measured according to the number of nozzles when the Reynolds number based on the nozzle exit is about $10^4$. Mean velocity, Reynolds shear stress and turbulent kinetic energy were investigated in the downstream of jets. The Tollmien's theory holds for downstream only when a nozzle locates at the center. Jet interaction is influenced due to with or without a center nozzle. In addition, the two-dimensional numerical computation was conducted for 3-nozzle case to obtain the general flow structure near the nozzle exit, which verifies the formation of the recirculation region with captive vortices, that is, the evidence of the interaction between jets.