• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.11
• /
• pp.848-853
• /
• 2010

We have grown GaN nanowires by the low pressure MOCVD method on Ni deposited oxidized Si surface and have established optimum conditions by observing surface microstructure and its photoluminescence. Optimum growth temperature of $880^{\circ}C$, growth time of 30 min, TMG source flow rate of 10 sccm have resulted in dense nanowires on the surface, however further increase of growth time or TMG flow rate has not increased the length of nanowire but has formed nanocrystals. On the contrary, the increase of ammonia flow has increased the length of nanowires and the coverage of nanowire over the surface. The shape of nanowire is needle-like with a Ni droplet at its tip; the length is tens of micron with more than 40 nm in diameter. Low temperature photoluminescence obtained from the sample at optimum growth condition has revealed several peaks related to exciton decay near band-edge, but does not show any characteristic originated from one dimensional quantum confinement. Strong and broad luminescence at 2.2 eV is observed from dense nanowire samples and this suggests that the broad band is related to e-h recombination at the surface state in a nanowire. The current result is implemented to the nanowire device fabrication by nanowire bridging between micro-patterned neighboring Ni catalysis islands.

• Journal of the Korean Vacuum Society
• /
• v.1 no.3
• /
• pp.360-370
• /
• 1992

HWE(Hot-Wall Epitaxy) 방법에 의하여 pyrex 유리기판 위에 CdS 다결정 박막을 성장하였다. X-선 회절실험 결과 CdS 박막은 육방정이었는데 (0002)면보다 91013)면이 강 하게 성장됨을 알 수 있었다. 전자현미경으로 표면을 분석한 결과 입자의 크기는 기판의 온 도가 48$0^{\circ}C$, 증발원의 온도가 $610^{\circ}C$일 때 1~1.5$mu extrm{m}$로서 가장 컸다. 박막의 표면저항은 4-point probe로서 측정한 결과 10-8$\Omega$/\ulcorner이상이었다. 성장된 CdS 다결정 박막의 photoluminesence을 20K에서 측정하였는데 bound exciton, donor acceptor pair에 의한 발광이 관측되었다. Spectral response의 peak는 505nm이었다. CdS 다결정 박막의 표면 저항을 줄이기 위하여 여러 가지 온도에서 Indium을 확산시켰다. 그 결과 표면저항은 ~ $\times$ 101에서 ~ $\times$ 103$\Omega$/\ulcorner 정도 감소되었다. 50$0^{\circ}C$에 In을 1시간 확산시켰을 때 표면저항은 1300$\Omega$/\ulcorner이었다. 이 때 CdS : In의 운반자 농도는 1.2 $\times$ 1018cm-3, 이동도는 1.8cm-2/V-sec, 비저항은 1.3 $\times$ 10-2$\Omega$-cm이었다. CdS : In의 photoluminescence는 20K 에서 Gaussian curve를 보여 주었으며 peak의 위치는 510nm이었다. CdS : In 박막의 spectral response의 peak는 상온에서 500nm이다. CdS : In 광전도 cell의 sensitivity ${\gamma}$ =0.77이고, 최대 허용소비전력은 p=120mW, 100lux에서 rise time은 8 msec, decay time 은 6 msec이다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.3
• /
• pp.188-192
• /
• 2018

In this study, we fabricated an $NO_X$ gas sensor using a composite film of multi-walled carbon nanotubes (MWCNT)/zinc oxide (ZnO). Carbon nanotubes (CNTs) show good electronic conductivity and chemical-stability, and zinc oxide (ZnO) is a wide band gap semiconductor with a large exciton binding energy. Gas sensors require characteristics such as high speed, sensitivity, and selectivity. The fabricated gas sensor was used to detect $NO_X$ gas at different $NO_X$ concentrations. The sensitivity of the gas sensor increased with increasing gas concentrations. Additionally, while changing the temperature inside the chamber containing the MWCNT/ZnO gas sensor, we obtained the sensitivity and normalized responses for detecting $NO_X$ gas in comparison to ZnO and MWCNT film gas sensors. From the experimental results, we confirmed that the gas sensor sensing mechanism was enhanced in the composite-film gas-sensor and that the electronic interaction between MWCNT and ZnO contributed to the improved sensor performance.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.340-341
• /
• 2013

양자점(Quantum dots; QDs)은 단전자 트랜지스터, 레이저, 발광다이오드, 적외선 검출기와 같은 고효율 광전소자 응용을 위해 활발한 연구가 진행되고 있다. II-VI 족 화합물 반도체는 III-V 족 화합물 반도체와 비교했을 때 더 큰 엑시톤 결합에너지(exciton binding energy)를 가지는 우수한 특성을 보이고 있으며 이러한 성질을 가지는 II-VI 족 화합물 반도체 중에서도 넓은 에너지 갭을 가지는 CdTe 양자점은 녹색 영역대의 광전자 소자로서 활용되고 있다. 기존의 CdTe/ZnTe 양자점을 성장하기 위해 ZnTe와 격자부정합이 적은 GaAs 기판을 이용한 연구가 주를 이룬 반면 Si기판을 이용한 연구는 미흡하다. 하지만 Si 기판은 GaAs 기판에 비해 값이 싸고, 여러 분야에 응용이 가능하며 대량생산이 가능하다는 이점을 가지고 있어 초고속, 초고효율 반도체 광전소자의 제작을 가능케 할 것으로 기대된다. 또한 양자점의 고효율 광전소자에 응용을 위해서는 Si 기판 위에 양자점의 크기를 효율적으로 조절하는 연구 뿐 아니라 양자점의 크기에 따른 운반자 동역학에 대한 연구도 중요하다. 본 연구에선 분자선 에피 성장법(Molecular Beam Epitaxy; MBE)과 원자층 교대 성장법(Atomic Layer Epitaxy; ALE)을 이용하여 Si 기판 위에 성장한 CdTe/ZnTe 양자점의 크기에 따른 광학적 특성을 연구하였다. 저온 광 루미네센스(PhotoLuminescence; PL) 측정 결과 양자점의 크기가 증가함에 따라 더 낮은 에너지영역으로 피크가 이동하는 것을 확인하였다. 그리고 온도 의존 광루미네센스 측정 결과 양자점의 크기가 증가함에 따라 열적 활성화 에너지가 증가하는 것을 관찰하였는데, 이는 양자점의 운반자 구속효과가 증가하였기 때문이다. 또한 시분해 광루미네센스 측정 결과 CdTe/ZnTe 양자점의 크기가 증가함에 따라 소멸 시간이 긴 값을 갖는 것을 관찰하였는데, 이는 양자점의 크기가 증가함에 따라 엑시톤 진동 세기가 감소하였기 때문이다. 이와 같은 결과 Si 기판 위에 성장한 CdTe/ZnTe 양자점의 크기에 따른 열적 활성화 에너지와 운반자 동역학에 대해 이해 할 수 있었다.

• Advances in nano research
• /
• v.5 no.3
• /
• pp.261-279
• /
• 2017

Spectroscopic investigation of Si quantum dots (Si-QDs) embedded in silicon nitride was performed over a broad stoichiometry range to optimize light emission. Plasma-enhanced chemical vapor deposition was used to grow the $SiN_x$ films on Si (001) substrates. The film composition was controlled via the flow ratio of silane ($SiH_4$) and ammonia ($NH_3$) in the range of R = 0.45-1.0 allowed to vary the Si excess in the range of 21-62 at.%. The films were submitted to annealing at $1100^{\circ}C$ for 30 min in nitrogen to form the Si-QDs. The properties of as-deposited and annealed films were investigated using spectroscopic ellipsometry, Fourier transform infrared spectroscopy, Raman scattering and photoluminescence (PL) methods. Si-QDs were detected in $SiN_x$ films demonstrating the increase of sizes with Si excess. The residual amorphous Si clusters were found to be present in the films grown with Si excess higher than 50 at.%. Multi-component PL spectra at 300 K in the range of 1.5-3.5 eV were detected and nonmonotonous varying total PL peak versus Si excess was revealed. To identify the different PL components, the temperature dependence of PL spectra was investigated in the range of 20-300 K. The analysis allowed concluding that the "blue-orange" emission is due to the radiative defects in a $SiN_x$ matrix, whereas the "red" and "infrared" PL bands are caused by the exciton recombination in crystalline Si-QDs and amorphous Si clusters. The nature of radiative and no radiative defects in $SiN_x$ films is discussed. The ways to control the dominant PL emission mechanisms are proposed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.79-80
• /
• 2006

A stoichiometric mixture of evaporating materials for $CdIn_2S_4$ single crystal thin films was prepared from horizontal electric furnace. To obtain the single crystal thin films, $CdIn_2S_4$ mixed crystal was deposited on thoroughly etched semi-Insulating GaAs(100) substrate by the Hot Wall Epitaxy (HWE) system. The temperature dependence of the energy band gap of the $CdIn_2S_4$ obtained from the absorption spectra was well described by the Varshni's relation. $E_g(T)=2.7116 eV-(7.74{\times}10^{-4} eV)T^2/(T+434)$. The crystal field and the spin-orbit splitting energies for the valence band of the $CdIn_2S_4$ have been estimated to be 0.1291 eV and 0.0248 eV, respectively, by means of the photocurrent spectra and the Hopfield quasicubic model. These results indicate that the splitting of the ${\Delta}so$ definitely exists in the ${\Gamma}_5$ states of the valence band of the $AgInS_2$/GaAs epilayer. The three photocurrent peaks observed at 10K are ascribed to the $A_1-$, $B_1-$, and C1-exciton peaks for n = 1.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.11-11
• /
• 2006

ZnO는 넓은 밴드갭(3.37eV)과 큰 액시톤(exciton) 결합에너지(60meV)를 가지는 II-VI족 화합물 반도체이다[1]. 이와같은 특성은 상온에서도 높은 재결합 효율이 기대되는 엑시톤 전이가 가능하여 자발적인 발광특성 및 레이저 발진을 위한 낮은 임계전압을 가져 일광효율이 큰 장점이 있다. 최근에는 ZnO의 전기적, 광학적, 자기적 특성을 높이기 위해 doping에 대한 연구가 많이 보고 되고 있다. 이중 ZnO내에 Mg을 doping하게 되면 Mg 조성에 따라 밴드갭이 3.3~7.7eV까지 변하게 된다. 그러나 이원계 상평형도에 따라 ZnO내에 고용될 수 있는 MgO의 고용도는 4at% 이하이다. 이는 ZnO는 Wurtzite 구조이고, MgO는 rocksalt 구조로 각각 결정구조가 다르기 때문이다. 본 연구는 열기상증착방법(thermal evaporation)으로 ZnO 템플레이트를 이용하여 MgZnO 나노막대를 합성하였고, Zn와 Mg의 서로 다른 녹는점을 이용해 2-step으로 성장을 하였다. 합성은 수평로를 사용하였으며, 반응온도 550, $700^{\circ}C$로 2-step으로 하였으며, 소스로 사용된 Zn(99.99%)과 Mg(99.99%) 분말을 산소를 직접 반응시켜 합성하였다. Ar 가스와 O2 가스를 각각 운반가스와 반응가스로 사용하였다. ZnO 템플레이트 위에 성장시킨 1차원 MgZnO 나노구조의 형태 및 구조적 특성을 FESEM과 TEM으로 분석하였다. 그리고 결정학적 특성은 XRD를 이용해 분석하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1995.02a
• /
• pp.36-36
• /
• 1995

The cubic (zinc blende) CdSe eppilayers were grown on GaAs(100) substrates by electron beam (e-beam) evapporation technique. X-ray scans with copper $K\alpha$ radiation indicate that the CdSe eppilayers are zinc blende. The lattice pparameter obtained from the (400) reflection is 6.077$\AA$, which is in excellent agreement with the value repported in the literature for zinc blende CdSe. The orientation of as-grown CdSe eppilayer is determined by electron channeling ppatterns(ECpp). The crystallinity of heteroeppitaxial CdSe layers were investigated based on the double crystal x-ray rocking curve(DCRC). The deppendence of the rocking curve width on layer thickness was studied. The FWHM(full width at half maximum) of CdSe eppilayers grown on GaAs(100) substrates is decreasing with increasing eppilayer thickness. The carrier concentration and mobility of the as-grown eppilayers deduced Hall data by van der ppauw method, are about 7$\times$1017 cm-3 and 2$\times$102 $\textrm{cm}^2$ / sec at room tempperature, resppectively. The energy gapp was determinded from the pphotocurrent sppectrum. In pphotocurrent sppectrum of a 1-${\mu}{\textrm}{m}$-thick CdSe eppilayer at 30K, the ppeak at 1.746 eV is due to the free exciton of cubic CdSe. In summary, We have shown that eppilayers of zinc blende CdSe can be grown on GaAs(100) substrates by e-beam, desppite the large mismatch between eppilayer and substrate, as well as the natural ppreference for CdSe to form in the wurtzite structure.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.2
• /
• pp.220-228
• /
• 1996

CdTe single crystals were grown by vertical Bridgman method using double furnace with two siliconit heating elements. When the peak temperature of the upper furnace was fixed at $1150^{\circ}C$ and that of the lower furnace was $800^{\circ}C$, the temperature gradient was about $22.5^{\circ}C$/cm. The lattice constant $a_0$ was $6.482\AA$ from the X-ray diffraction and the band gap energy obtained from the optical absorption experiment at room temperature was 1.478 eV. PL spectrum showed that the bound exciton emission peak was resolved into ($A^0,X$) (1.5902, 1.5887 eV), ($h\;D^0$) (1.5918 eV) and ($D^0,X$ (1.5928, 1.5932 eV), and we have also calculated binding energy and ionization energy of the neutral donor and acceptor.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.3
• /
• pp.91-94
• /
• 2007

Single-crystalline $SnO_2$ nanowires were successfully grown on Si(001) substrates via vapor-liquid-solid mechanism in a thermal chemical vapor deposition. Large quantity of $SnO_2$ nanowires were synthesized at temperature ranges of $950{\sim}1000^{\circ}C$ in Ar atmosphere. It was found that the grown $SnO_2$ nanowires are of a tetragonal rutile structure and single crystalline by diffraction and transmission electron microscopy measurements. Broad emission located at about 600 m from the grown nanowires was clearly observed in room temperature photoluminescence measurements, indicating that the emission band originated from defect level transition into $SnO_2$ nanowires.