• Transactions on Electrical and Electronic Materials
• /
• 제11권4호
• /
• pp.182-185
• /
• 2010

$Pb_{0.99}[(Zr_{0.6}Sn_{0.4})_{0.9}Ti_{0.1}]_{0.98}Nb_{0.02}O_3$ (PNZST) thin films were deposited by radio frequency magnetron sputtering on a $(La_{0.5}Sr_{0.5})CoO_3$ (LSCO)/Pt/Ti/$SiO_2$/Si substrate using a PNZST target with an excess PbO of 10 mole%. The thin films deposited at the substrate temperature of $500^{\circ}C$ crystallized to a perovskite phase after rapid thermal annealing (RTA). The thin films, which annealed at $650^{\circ}C$ for 10 seconds in air, exhibited good crystal structures and ferroelectric properties. The remanent polarization and coercive field of the fabricated PNZST capacitor were approximately $20uC/cm^2$ and 50 kV/cm, respectively. The reduction of the polarization after $2.2\;{\times}\;10^9$ switching cycles was less than 10%.

• 한국세라믹학회지
• /
• 제30권8호
• /
• pp.671-677
• /
• 1993

Effects of PbTiO3 addition on dielectric properties and extent of PbO loss in Nd-doped Pb(Mg1/3Nb2/3)O3 system were investigated. As the proportion of dopping increased, the phase transition temperature shifted to low region, and the dielectric constant at room temperature decreased rapidly. But as the proportion of PbTiO3 increased, the phase transition temperature shifted to high retion, and the dielectric constant at room temperature increased. The substitution of Nd3+ for Pb2+ decreased the amount of PbO evaporation, therefore the sample sintered well in case of only 1 mole% adding excess PbO.

• 한국세라믹학회지
• /
• 제17권2호
• /
• pp.89-95
• /
• 1980

The effect of non-stoichimetry and sintering temperature on the magnetic properties of materials in the system $Ni_{0.39}Zn_{0.61}Fe_{2.0+x}O_4$ have been investigated. The value of x used in initial weighing of oxides were varied from -0.04 to -0.12. The value of x, however, appears to be from +0.04 to -0.04 after ferrite powder preparation due to iron pick up during ball mill mixing and grinding. The densities of specimens which were deficientinrion were higher than those with excess ion. Specimens with near stoichiometric composition showed maximum initial permeability an dminimum coercivity whereas high values of quality factor (Q) were observed in iron deficient specimens. The quality factor decreased monotonically with increasing sintering temperature, but the permeability showed maxima with increasing sintering temperature. Thus highest value of figure of merit $\mu$Q was obtained in composition $Ni_{0.39}Zn_{0.61}Fe_{1.98O4}$ sintered at 100$0^{\circ}C$ for 3 hrs. in an air atmosphere.

• 한국세라믹학회지
• /
• 제37권8호
• /
• pp.787-791
• /
• 2000

Samples with the nominal composition, Bi2-xGexSr2CaCu2O8＋$\delta$ (x=0, 0.1, 0.2, 0.3, 0.4, 0.5) were prepared by the solid-state reaction method. We have studied the effect of substitution Ge for Bi and investigated the superconducting properties by changing oxygen content with Ge substitution. It was found that temperature difference, ΔK, between TCon and TCzero was considerably smaller in the samples prepared by the intermediate pressing method than that in the samples by the solid-state reaction method. We found the solubility limit of Ge to the 80 K single phase was around x=0.3. Within the solubility limit, lattice constant c decreased with the increase of x. In the region of the 80K single phase, the onset critical temperature TCon increased and excess oxygen content decreased with increase of x.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.81-82
• /
• 2006

The purposes of the present study are to produce a high thermal efficient of oil-based nanofluids which can be used as ultra-high voltage transformer oil, and to investigate their thermal and physical properties under static and dynamic conditions. Three kinds of nanofluids are prepared by dispersing $Al_2O_3$ or AlN nanoparticles in transformer oil. The thermal conductivities of the nanoparticles-oil mixtures increase with temperature, particle volume concentration and thermal conductivity of solid particle itself. It was quite important to eliminate $H_2O$ as byproducts of esterification and excess oleic acid which did not form stable chemical bonds with powder surface to get high dispersion stability.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.415-420
• /
• 2000

This paper describes a part of the results obtained in the process of the development of thin sound isolation sheets filled mineral compound powder with PVC. The raw materials used are pyrophillite, pottery stone and graphite. The physical properties such as the crystal structures, compositions, and specific gravities, etc. of raw materials are analyzed and discussed from a point of view of sound isolation material. From the analysis of experimental results, the particle size and the additive amount of mineral compound powder for manufacturing sample isolation sheets are decided. The resistant capability against fire of sound isolation sheets including mechanical, thermal and physical properties is tested. The transmission loss measuremenst of sound isolation sheets are performed using two-microphone method in an impedance tube. It is shown that the sound isolation capability of thin sheets has an excellent performance in excess of the object of development.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.851-856
• /
• 2003

We have investigated the material and electrical properties of $Bi_{4-x}La_xTi_3O_{12}$ (BLT) ferroelectric thin film for ferroelectric nonvolatile memory applications of capacitor type and single transistor type. The 120nm thick BLT films were deposited on $Pt/Ti/SiO_2/Si$ and $SiO_2/Nitride/SiO_2$ (ONO) substrates by the sol-gel spin coating method and were annealed at $700^{\circ}C$. It was observed that the crystallographic orientation of BLT thin films were strongly affected by the excess Bi content and the intermediate rapid thermal annealing (RTA) treatment conditions regardeless of two type substrates. However, the surface microstructure and roughness of BLT films showed dependence of two different type substrates with orientation of (111) plane and amorphous phase. As increase excess Bi content, the crystallographic orientation of the BLT films varied drastically in BLT films and exhibited well-crystallized phase. Also, the conversion of crystallographic orientation at intermediate RTA temperature of above $450^{\circ}C$ started to be observed in BLT thin films with above excess 6.5% Bi content and the rms roughness of films is decreased. We found that the electrical properties of BLT films such as the P-V hysteresis loop and leakage current were effectively modulated by the crystallographic orientations change of thin films.

• 대한화학회지
• /
• 제17권2호
• /
• pp.73-79
• /
• 1973

界面活性劑 dodecyl pyridinium bromide(D.P.B.) $20^{\circ}C$ 濃度 5∼100mM 水溶液中에서 0.1Mc~90Mc 超音波의 吸收 係數를 測定정하였다. 監 存在 與否에 關係없이 臨界 micelle 濃度(c.m.c.)以上의 濃度에서만 超音波超過 吸收가 觀測되었다. 超音波 吸收 曲線에서 D.P.B.水溶液 60mM附近에 超過 吸收 및 relaxation 振動數의 不連續的인 變化를 觀測하였다. 또 粘性係數, 電氣傳導度, 超音破速度들의 濃度曲線 에서도 같은 濃度에서 不連續的인 變化를 나타낸다. 따라서 이 濃度 附近에서 D.P.B.의 micelle의 性質에 變化가 일어나고 있다고 結論지을 수 있다. 超音波超過 吸收의 mechanism은 $M_2{\rightleftharpoons}M_1+2Br^-$ 反應에 基因됨을 알았다. 여기서 $M_2$,$ M_1$은 다른 型의 micelle이다. 正, 逆方向의 反應速度常數는 各各 $6.9 {\times} 10^5 sec^{-1)$, $6.7{\times}10^{10}sec^{-1}mole{-2}$임이 觀測되었다. 이 反應 mechanism의 自由 에너지, enthalpy, entropy 및 活性化에너지를 算出하였다.

• Korean Chemical Engineering Research
• /
• 제57권1호
• /
• pp.78-84
• /
• 2019

최근 지속 가능형 에너지로 바이오 부탄올(bio-butanol)에 관한 연구가 활발히 진행되고 있으나, 이의 상업화에는 저렴한 바이오메스 개발 및 경제적 분리 방법 등 선결해야 할 문제들이 있다. 전통적인 ABE 바이오부탄올 발효공정은 아세톤, 부탄올, 에탄올과 함께 유기산(organic acid)과 같은 부산물을 생성한다. 따라서 이들의 상호분리를 위해 아세톤, 부탄올, 에탄올 및 아세틱 산에 대한 상평형 데이터 등은 많이 발표되었으나, 탄소수가 큰 유기산에 대한 상평형 및 혼합물성 데이터는 매우 부족한 실정이다. 따라서 본 연구는 $C_3-C_6$ 유기산 조합의 이성분계 혼합물에 대한 고-액 상평형과 혼합물성으로 과잉부피($V^E$), 굴절율 편차(${\Delta}R$) 그리고 점도 편차(${\Delta}v$)를 298.15 K에서 실험적으로 측정하였다. 측정된 고-액 상평형 데이터는 NRTL, UNIQUAC식을 이용하여 상관시켰으며 RMSD, 0.5 K이하로 잘 상관되었다. 또한 동일 이성분계 혼합물에 대한 $V^E$, ${\Delta}R$ 및 ${\Delta}v$의 혼합물성 데이터는 Redlich-Kister 다항식을 이용해 매개변수를 상관하였으며 약 0.004 이하의 표준편차로 잘 상관됨을 확인하였다.

• 한국환경보건학회지
• /
• 제47권5호
• /
• pp.398-409
• /
• 2021

Background: The types and effects of hazardous pollutants in indoor air may vary depending on the characteristics of the sources and pollutants caused by physical and chemical properties of buildings, the influence of outdoor air, and the exposure and use characteristics of residents. Objectives: This study was conducted to provide basic data on the establish of indoor air quality management for different classes of public-use facilities by presenting the characteristics of concentration distribution of hazardous pollutants by different public-use facilities and the status of the excess proportion of exceeding standards. Methods: This study analyzed self-measurement data from public-use facilities taken from 2017 to 2019 A total of 133,525 facilities were surveyed. A total of 10 types of pollutants that have maintenance and recommended standards stipulated in the Indoor Air Quality Control Act from the Ministry of Environment were investigated. The excess proportion and the substances exceeding the criteria for each type of public-use facilities for these pollutants were investigated. Results: As a result of the analysis of the proportion of exceeding the standard for each type of public-use facility, the facilities with the highest excess proportion of the standards for each hazardous pollutant were: PM₁₀ in railway stations (8.93%), PM_2.5 in daycare centers (7.36%), CO₂ in bus terminals (2.37%), HCHO in postpartum care centers (4.11%), total airborne bacteria in daycare centers (0.69%), CO in museums (0.1%), NO₂ in postpartum care centers (1.15%), Rn in museums (0.78%), total volatile organic compounds in postpartum care centers (7.20%) and mold in daycare centers (1.44%). Conclusions: Although uncertainty may arise because this study is a result of self-measurement, it is considered that this study has significance for providing basic data on the establishment in the future of indoor air quality management measures customized for each type of public-use facility.