• 한국세라믹학회지
• /
• 제37권2호
• /
• pp.186-193
• /
• 2000

Effects of 1.0 mol% CoO addition on sintering and the electrical properties of ZnO-Bi2O3-Sb2O3(ZBS) varistor system with 3.0 mol% co-addition of Sb2O3 and Bi2O3 at various Sb/Bi ratio (0.5, 1.0, and 2.0) were investigated. Cobalt had little influence on the liquid-phase formation and the pyrochlore decomposition temepratures of ZBS, while densification was mainly dependent on Sb/Bi ratio: when Sb/Bi=0.5, excess Bi2O3 irrelevant to the formation of pyrochore(Zn2Sb3Bi3O14) forms eutectic liquid at ~75$0^{\circ}C$ which promotes densification and grain growth; with Sb/Bi=2.0, the second phase Zn7Sb2O12 formed by excess Sb2O3 irrelevant to the formation of the pyrochlore retards densification up to ~100$0^{\circ}C$. These phases caused the coarsening and uneven distribution of the second phase particles on the grain boundaries of ZnO above the pyrochlore decomposition temperature(~105$0^{\circ}C$), which led to broad size dist-ribution of ZnO; the specimen with Sb/Bi=1.0 showed homogeneous microstructure compared with the others, which enabled improved varistor characteristics. Doping of Co increased the nonlinearity and the potential barrier height of ZBS, which is thought to stem from improved sintering behavior such as homogenized microstructure due to size reduction and even distribution of the second phase and suppressed volatility of Bi2O3, as well as the improvement in the potential barrier structure via increased donor and interface electron trap densities.

• 한국전기전자재료학회논문지
• /
• 제29권4호
• /
• pp.210-214
• /
• 2016

We investigated the sintering behavior and piezoelectric properties of lead-free $(K_{0.5}Na_{0.5})NbO_3$ ceramics co-doped with excess 0.01 mol ZnO and x mol $MnO_2$, where x was varied from 0 to 0.03. Excess $MnO_2$ addition was found to retard the grain growth and densification during sintering. However, 0.005 mol $MnO_2$ addition improved the piezoelectric properties of 0.01 mol ZnO added $(K_{0.5}Na_{0.5})NbO_3$ ceramics. The planar mode piezoelectric coupling coefficient, electromechanical quality factor, and piezoelectric constant $d_{33}$ of 0.01 mol ZnO and 0.005 mol $MnO_2$ added specimen were 0.40, 304, and 214 pC/N, respectively.

• 한국재료학회지
• /
• 제23권3호
• /
• pp.161-167
• /
• 2013

The ZnO thin films were grown on GaN template substrates by RF magnetron sputtering at different RF powers and n-ZnO/p-GaN heterojunction LEDs were fabricated to investigate the effect of the RF power on the characteristics of the n-ZnO/p-GaN LEDs. For the growth of the ZnO thin films, the substrate temperature was kept constant at $200^{\circ}C$ and the RF power was varied within the range of 200 to 500W at different growth times to deposit films of 100 nm thick. The electrical, optical and structural properties of ZnO thin films were investigated by ellipsometry, X-ray diffraction (XRD), atomic force microscopy (AFM), photoluminescence (PL) and by assessing the Hall effect. The characteristics of the n-ZnO/p-GaN LEDs were evaluated by current-voltage (I-V) and electroluminescence (EL) measurements. ZnO thin films were grown with a preferred c-axis orientation along the (0002) plane. The XRD peaks shifted to low angles and the surface roughness became non-uniform with an increase in the RF power. Also, the PL emission peak was red-shifted. The carrier density and the mobility decreased with the RF power. For the n-ZnO/p-GaN LED, the forward current at 20 V decreased and the threshold voltage increased with the RF power. The EL emission peak was observed at approximately 435 nm and the luminescence intensity decreased. Consequently, the crystallinity of the ZnO thin films grown with RF sputtering powers were improved. However, excess Zn affected the structural, electrical and optical properties of the ZnO thin films when the optimal RF power was exceeded. This excess RF power will degrade the characteristics of light emitting devices.

• Geomechanics and Engineering
• /
• 제16권3호
• /
• pp.233-245
• /
• 2018

Interest to basal reinforced piled embankments is increasing recently due to their rapid construction and reliability. A comprehensive parametric study is conducted to determine effects of pile properties, reinforcement stiffness, embankment properties and soft soil properties into settlements, pressures and excess pore water pressure development and dissipations. Results which are obtained by using one-layer reinforcement during construction are compared with the results obtained by using two-layer reinforcement during construction. Finite element method is used during the parametric study. Second layer of reinforcement is placed in five different positions in order to reveal effects of reinforcement position into behaviour. Traffic load is also taken into consideration during the study. Differences between the results without presence of traffic loading and with presence of traffic loading is stated in this the study.

• Composites Research
• /
• 제28권6호
• /
• pp.361-365
• /
• 2015

The influence of MWCNTs on fracture toughness properties of MWCNTs/Nickel-Pitch Fibers/epoxy composites (MWCNTs/Ni-PFs/epoxy) was investigated according to MWCNTs content. Nickel-Pitch-based carbon fibers (Ni-PFs) were prepared by electroless nickel-plating. The surface properties of Ni-PFs were determined by scanning electron microscopy (SEM) and X-ray photoelectron spectrometry (XPS). The fracture toughness of MWCNTs/Ni-PFs/epoxy was assessed by critical stress intensity factor ($K_{IC}$) and critical strain energy release rate ($G_{IC}$). From the results, it was found that the fracture toughness properties of MWCNTs/Ni-PFs/epoxy were enhanced with increasing MWCNTs content, whereas the value decreased above 5 wt.%. MWCNTs content. This was probably considered that the MWCNTs entangled with each other in epoxy due to an excess of MWCNTs.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1992년도 봄 학술발표회 논문집
• /
• pp.41-46
• /
• 1992

A potential use of superplasticizing admixture is to produce structural concrete of High-strength concrete,. By using a superplasticizer, more workable mixes can be achieved while permitting a high cement content and a low water/cement ratio both of which are necessary to obtain high strength by conventional manufacturing technique. In this study, therefore, high strength concrete having a 28-day strength in excess of 650kg/$\textrm{cm}^2$ can be obtained using a superplasticzer. However, before such a high strength concrete is recommended for use, engineering properties have to be assessed. This study is aimed to analyze and investigate the engineering properties, such as strength, elasticity, ultrasonic pulse velocity, rebound value of superplasticized concrete having a various cement content.

• Transactions on Electrical and Electronic Materials
• /
• 제8권4호
• /
• pp.153-156
• /
• 2007

Structural and electrical properties of the fully crystallized-bismuth magnesium niobate ($Bi_2Mg_{2/3}Nb_{4/3}O_7$, BMN) films with 15 mol% excess bismuth deposited on Pt bottom electrode by pulsed laser deposition are characterized for various deposition temperatures. The BMN films were crystallized with a monoclinic structure from $300^{\circ}C$ and the surface roughness slightly decreases with increasing deposition temperature. The capacitance density of the films increases with increasing deposition temperature and especially, films deposited at $400^{\circ}C$ exhibit a capacitance density of approximately $620nF/cm^2$. The crystallized BMN films with approximately 170 nm thickness exhibit breakdown strength above 600 kV/cm (${\leq}10V$) irrespective of deposition temperature and a leakage current density of approximately $2{\times}10^{-8}A/cm^2$ at 590kV/cm (at 10 V).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 추계학술대회 논문집
• /
• pp.320-323
• /
• 2000

We attempted to fabricate polyurethane derivatives (PU-CN, PU-DCM) LB films by using LB method. Also, we investigated the monolayer behavior at the air-water interface by surface pressure-area ($\pi$-A) isotherms. And, the surface morphologies and the physicochemical properties of LB films were investigated by atomic force microscopy (AFM) and UV-vis spectroscopy, respectively. Also, the electrical properties of polyurethane derivatives LB films were investigated by using the conductivity and the dielectric constant. In the AFM images, we conclude that surface morphology of PU-DCM LB films is smooth and homogeneous and has optimal hydrophobicity and good stability, whereas PU-CN LB films give rougher surfaces with more excess material. In the I-V characteristics, the conductivity is different as to the polyurethane derivatives, it is considered that this phenomena could be described by the difference of lumophore pendant which was adhered at PU main chain.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.359-360
• /
• 2005

PZT(20/80) and PZT(80/20) powders, prepared by the sol-gel method, were mixed with an organic vehicle and the PZT(20/80)/PZT(80/20) heterolayered thick films were fabricated by the screen-printing method on Pt/$Al_2O_3$ substrates. The structural properties such as DTA, X-ray diffraction and microstructure, were examined as a amount of the excess PbO. In the DTA analysis, the formation of the polycrystalline perovskite phase was observed at around $880^{\circ}C$. The average thickness of the PZT heterolayered thick films was approximately $80{\mu}m$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.242-243
• /
• 2005

In this study, (La,Sr)$MnO_{3+\delta}$ powder used cathode material for SOFC was synthesized with precursor by GNP and the properties of powder, crystal phase, electric properties and deoxidization properties with precursor were investigated. The synthesis powder was prepared when oxidant/fuel mole and pH were 1 and 1, respectively and the synthesis powder was synthesized by GNP method using nitrate solution or oxide solution as precursor. Deoxidization peak of the nitrate solution was appeared lower temperature than the oxide solution, at $450^{\circ}C$. In this result, synthesis (La,Sr)$MnO_{3+\delta}$ powder using nitrate solution with Mn excess was suitable cathode material for SOFC due to had higher deoxidization properties. Also synthesis (La,Sr)$MnO_{3+\delta}$ powder according to precursor had difference electrical conductivity according to influence sintering density and crystal phase with precursor. Specially, the synthesis method and starting material had effect on deoxidization properties for SOFC.