• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.455-456
• /
• 2008

In this study, we report that an electrical properties of OLEDs was investigated by the surface etching method of ITO Layer. The electrical properties of OLEDs was measured by IVL and optical properties by EL spectrum. The fundamental structure of OLEDs was ITO anode/TPD(400$\breve{A}$)/$Alq_3(600\breve{A})$/LiF(5$\breve{A}$)/Al(1200$\breve{A}$) cathode. The threshold voltage was low value according to the low resistance of surface. The luminance was increased by decreased surface resistance.

• 대한전기학회논문지
• /
• 제45권3호
• /
• pp.438-443
• /
• 1996

The effect of plasma polymerization conditions on the structure of the plasma polymerized styrene were investigated by using Fourier Transform Infrared Ray(FT-IR), Differential Scanning Calorimetry (DSC), Gel Permeation Chromatography(GPC). Plasma polymerized thin film was prepared using an interelectrode inductively coupled gas-flow-type reactor. We show that polymerization parameters of thin film affect sensitivity and etching resistance of plasma polymerized styrene is 1.41~3.93, and deposition rate of that are 32~383[.angs./min] with discharge power. Swelling and etching resistance becomes more improved with increasing discharge power during plasma polymerization. (author). 11 refs., 10 figs., 1 tab.

• Tribology and Lubricants
• /
• 제40권3호
• /
• pp.84-90
• /
• 2024

This study investigates the effect of the surface microstructure on the tribological characteristics of glass substrates. Chemical etching using hydrofluoric acid and ammonium hydrogen fluoride was employed to create controlled asperity structures on glass surfaces. By varying the etching time from 10 to 50 min, different surface morphologies were obtained and characterized using optical microscopy, surface roughness measurements, and water contact angle analysis. Friction tests were performed using a stainless steel ball as the counter surface to evaluate the tribological behavior of the etched specimens. The results showed that the specimen etched for 20 min exhibited the lowest and most stable friction coefficient, which was attributed to the formation of a uniform and dense asperity structure that effectively reduced the stress concentration and wear at the contact interface. In contrast, specimens etched for shorter (10 min) or longer (30-50 min) durations displayed higher friction coefficients and accelerated wear owing to nonuniform asperity structures that led to local stress concentration. Optical microscopy of the wear tracks further confirmed the superior wear resistance of the 20-minute etched specimen. These findings highlight the importance of optimizing the etching process parameters to achieve the desired surface morphology for enhanced tribological performance, suggesting the potential of chemical etching as a surface modification technique for various materials in tribological applications.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.268-271
• /
• 2005

Etch resistance of mask layer on silicon substrate modified by AFM-based Tribo-Nanolithography (TNL) in Aqueous Solution in an aqueous solution was demonstrated. n consists or sequential processes, nano-scratching and wet chemical etching. The simple scratching can form a mask layer on the silicon substrate, which acting as an etching mask. For TNL, a specially designed cantilever with diamond tip, allowing the formation of mask layer on silicon substrate easily by a simple scratching process, has been applied instead of conventional silicon cantilever fur scanning. This study demonstrates how the TNL parameters can affect the etch resistance of mask layer, hence introducing a new process of AFM-based maskless nanolithography in aqueous solution.

• 한국전기전자재료학회논문지
• /
• 제16권5호
• /
• pp.424-428
• /
• 2003

The channel of a superconducting flux flow transistor has been fabricated with plasma etching method using a inductively coupled plasma etching. The ICP conditions then were ICP Power of 450 W, rf chuck power of 150 W, the pressure in chamber of 5 mTorr, and Ar : Cl$_2$=1:1. Especially, over the 5 mTorr, the superconducting thin films were not etched. The channel etched by plasma gas showed the critical temperature over 85 K. The critical current of the SFFT was altered by varying the external applied current. As the external applied current increased from 0 to 12 mA, the critical current decreased from 28 to 22 mA. Then the obtained trans-resistance value was smaller than 0.1 $\Omega$ at a bias current of 40 mA.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.906-911
• /
• 2004

In this paper, we used only PR as etching mask, while it used usually Cr/AU as etching mask, and in order to fabricate a photosensor has the increased sensitivity, we investigated on the sensitivity of general type and p-i-n type diode. we designed microchannel size width max 10um, min 5um depth max 10um, reservoir size max 100um, min 2mm. Fabrication of microfluidic devices in glass substrate by glass wet etching methods and glass to glass fusion bonding. The p-i-n diode has higher sensitivity than photodiode. Considering these results, we fabricated p-i-n diodes on the high resistive($4k{\Omega}{\cdot}cm$) wafer into rectangle and finger pattern and compared internal resistance of each pattern. The internal resistance of p-i-n diode can be decreased by the application of finger pattern has parallel resistance structure from $571\Omega$ to $393\Omega$.

• 반도체디스플레이기술학회지
• /
• 제21권1호
• /
• pp.119-126
• /
• 2022

MAS-based glass, which has been studied to replace the ceramic material used in the plasma etching chamber, has problems such as forming and processing due to its high melting temperature. To solve this problem, in this study, fluoride was added to the existing MAS-based glass to increase the workability in the glass manufacturing and to improve the chemical resistance to CF₄/Ar/O₂ plasma gas. Through RAMAN analysis, the structural change of the glass according to the addition of fluoride was observed. In addition, it was confirmed that high-temperature viscosity and thermal properties decreased as the fluoride content increased and plasma resistance was maintained, it showed an excellent etching rate of up to 11 times compared to quartz glass.

• Carbon letters
• /
• 제13권1호
• /
• pp.44-47
• /
• 2012

We analyzed the effect of etchants for metal catalysts in terms of the characteristics of resulting graphene films, such as sheet resistance, hall mobility, transmittance, and carrier concentration. We found the residue of $FeCl_3$ etchant degraded the sheet resistance and mobility of graphene films. The residue was identified as an iron oxide containing a small amount of Cl through elemental analysis using X-ray photoelectron spectroscopy. To remove this residue, we provide an alternative etching solution by introducing acidic etching solutions and their combinations ($HNO_3$, HCl, $FeCl_3$ + HCl, and $FeCl_3+HNO_3$). The combination of $FeCl_3$ and acidic solutions (HCl and $HNO_3$) resulted in more enhanced electrical properties than pure etchants, which is attributed to the elimination of left over etching residue, and a small amount of amorphous carbon debris after the etching process.

• 소성∙가공
• /
• 제13권3호
• /
• pp.268-272
• /
• 2004

Transparent materials such as fused silica are widely utilized in optical and optoelectronics field because of its outstanding properties, such as transparency in a wide wavelength range, strong damage resistance for laser irradiation, and high thermal and chemical stability. In this study, we made a few micro patterns on the surface of fused silica plate using laser induced wet etching. KrF excimer laser was used as a light source. There were no burrs and micro cracks on the etched surface of fused silica and the flatness of the etched surface was fairly good. We investigated the influence of etchant upon the etch rate and quality in laser induced wet etching. Pyrene-acetone solution and toluene were used as etchant. In the side of etch rate, toluene solution was better than pyrene-acetone solution. But we made in wider range of energy density using pyrene-acetone solution. But pyrene-acetone solution gave us wider window of energy density for successful micro patterning.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.234-235
• /
• 2006

In this study, the plasma sprayed $Al_2O_3$ and $Y_2O_3$ coatings have been investigated for applications of microelectronic components. The plasma sprayed coatings had a well-defined splatted lamellae microstructure, intersplat pores and a higher amount of microcracks within the splats. The plasma sprayed $Y_2O_3$ coating had a relatively lower hardness of 300-400Hv, compared to 650-800Hv for $Al_2O_3$ coating, and would be readily damaged by mechanical attacks such as erosion, wear and friction. For a reactive ion etching against F-containing plasmas, however, the $Y_2O_3$ coating had a much higher resistance than the $Al_2O_3$ coating because of the reduced erosion rate of by-products.