• 통합자연과학논문집
• /
• 제2권3호
• /
• pp.207-210
• /
• 2009

Multiple rugate structures can be etched on a silicon wafer and placed in the same physical location, showing that many sharp spectral lines can be obtained in the optical reflectivity spectrum. Porous silicon samples were prepared by electrochemical etch of heavily doped p-type silicon wafers. The etching solution consisted of a 3:1 volume mixture of aqueous 48% hydrofluoric acid and absolute ethanol. Galvanostatic etch was carried out in a Teflon cell by using a two-electrode configuration with a Pt mesh counterelectrode. A sinusoidal current density waveform varying between 51.5 and $74.6mA/cm^2$ is applied. The anodization current was supplied by a Keithley 2420 high-precision constant current source which is controlled by a computer to allow the formation of PSi multilayer.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 추계학술대회 논문집
• /
• pp.583-586
• /
• 2000

The non-selective method by polishing after grinding was used widely to thinning of SDB SOI structures. This method was very difficult to thickness control of thin film, and it was dependent on equipments. However electrochemical etch-stop, one of the selective methods, was able to accurately thickness control and etch equipment was very simple. Therefore, this paper described with the effect of leakage current and electrodes on electrochemical etch-stop. Consequentially, PP(passivation potential) was changed according to the kinds of contact and contact sizes, but OCP(open current potential) was not change with range of -1.5~-1.3V

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.523-523
• /
• 2012

As the wafer geometric requirements continuously complicated and minutes in tens of nanometers, the expectation of real-time add-on sensors for in-situ plasma process monitoring is rapidly increasing. Various industry applications, utilizing plasma impedance monitor (PIM) and optical emission spectroscopy (OES), on etch end point detection, etch chemistry investigation, health monitoring, fault detection and classification, and advanced process control are good examples. However, process monitoring in semiconductor manufacturing industry requires non-invasiveness. The hypothesis behind the optical monitoring of plasma induced ion current is for the monitoring of plasma induced charging damage in non-invasive optical way. In plasma dielectric via etching, the bombardment of reactive ions on exposed conductor patterns may induce electrical current. Induced electrical charge can further flow down to device level, and accumulated charges in the consecutive plasma processes during back-end metallization can create plasma induced charging damage to shift the threshold voltage of device. As a preliminary research for the hypothesis, we performed two phases experiment to measure the plasma induced current in etch environmental condition. We fabricated electrical test circuits to convert induced current to flickering frequency of LED output, and the flickering frequency was measured by high speed optical plasma monitoring system (OPMS) in 10 kHz. Current-frequency calibration was done in offline by applying stepwise current increase while LED flickering was measured. Once the performance of the test circuits was evaluated, a metal pad for collecting ion bombardment during plasma etch condition was placed inside etch chamber, and the LED output frequency was measured in real-time. It was successful to acquire high speed optical emission data acquisition in 10 kHz. Offline measurement with the test circuitry was satisfactory, and we are continuously investigating the potential of real-time in-situ plasma induce current measurement via OPMS.

• 한국표면공학회지
• /
• 제30권1호
• /
• pp.44-56
• /
• 1997

Influence of electrochemical etching conditions on capacitance gain of aluminium electrolytic on capacitor foil has been investigated by etching cubic textured high purity aluminum foil in dilute hydrochloric acid. Uniformly distributed etch pit tunnels on aluminum surface have been obtained by pretreatment aluminium foil in 10% NaOH solution for 5 minutes followed by electrochemical etching. Electrostatic capacitance of etched aluminium foil anodized to high voltage increased with the increase of current density, total charge, temperature and concentration of electrolyte up to maximum CV-value and then deceased. Election optical observation of the etched foil revealed that the density of etch of etch pits increased with the increase of current density and concentration of electrolyte. this increase of etch pit density enlarged of the increase of capacitance. However, abnormal high current density and high electrolyte concentration induced the local dissolution of the foil surface which resulted the decrease of foil capacitance.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.232-233
• /
• 2008

The 4H-SiC schottky diodes treated by the various dry etch methods were fabricated and electrically characterized. The post etch process including an Inductively Coupled Plasma(ICP) etch and a Neutron Beam Etch(NBE) was performed after a high-temperature activation annealing without graphite cap in order to eliminate the damaged surface generated during the activation annealing. The reverse leakage current of diode treated by ICP was 1/35 times lower than that of the diode without any post etch at the anode bias of -100V, while the reverse leakage current of diode treated by NBE was 1/44 times lower at the same bias.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 학술대회지
• /
• pp.460-462
• /
• 2004

The control of the data retention time is a main issue for realizing future high density dynamic random access memory. There are several leakage current mechanisms in which the stored data disappears. The mechanisms of data disappear is as follow, 1 )Junction leakage current between the junction, 2) Junction leakage current from the capacitor node contact, 3)Sub-threshold leakage current if the transfer transistor is affected by gate etch damage etc. In this paper we showed the plasma edge damage effect to find out data retention time effectiveness. First we measured the transistor characteristics of forward and reverse bias. And junction leakage characteristics are measured with/without plasma damage by HP4145. Finally, we showed the comparison TRET with etch damage, damage_cure_RTP and hydrogen_treatment. As a result, hydrogen_treatment is superior than any other method in a curing plasma etch damage side.

• 한국전기전자재료학회논문지
• /
• 제17권4호
• /
• pp.373-377
• /
• 2004

We have investigated the electrical characterization of metal-oxide-semiconductor (MOS) capacitors formed on the inductively coupled plasma (ICP) etch-damaged both n- and p-type 4H-SiC. We found that there was an effect of a sacrificial oxidation treatment on the etch-damaged surfaces. Current-voltage and capacitance-voltage measurements of these MOS capacitors were used and referenced to those of prepared control samples without etch damage. It has been found that a sacrificial oxidation treatment can improve the electrical characteristics of MOS capacitors on etch-damaged 4H-SiC since the effective interface density and fixed oxide charges of etch-damaged samples have been found to increase while the breakdown field strength of the oxide decreased and the barrier height at the SiC-SiO$_2$ interface decreased for MOS capacitors on etch-damaged surfaces.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 춘계학술대회 논문집 전자세라믹스 센서 및 박막재료 반도체재료 일렉트렛트 및 응용기술
• /
• pp.126-129
• /
• 2000

This paper describes on the fabrication of a SOI substrate by SDB technology and electrochemical etch-stop. The surface of the thinned SDB SOI substrate is more uniform than that of grinding or polishing by mechanical method, and this process was found to be very accurate method for SOI thickness control. During electrochemical etch-stop, leakage current versus voltage curves were measured for analysis of the open current potential (OCP) point, the passivation potential (PP) point and anodic passivation potential. The surface roughness and the controlled thickness selectivity of the fabricated a SDB SOI substrate were evaluated by using AFM and SEM, respectively.

• 한국전기전자재료학회논문지
• /
• 제13권5호
• /
• pp.431-436
• /
• 2000

This paper describes on the fabrication of a SOI substrate by SDB technology and electrochemical etch-stop. The surface of the thinned SDB SOI substrate is more uniform than that of grinding or polishing by mechanical method and this process was found to be a very accurate method for SOI thickness control. During electrochemical etch-stop leakage current versus voltage curves were measured for analysis of the open current potential(OCP) point the passivation potential(PP) point and anodic passivation potential. The surface roughness and the controlled thickness selectivity of the fabricated a SDB SOI substrate were evaluated by using AFM and SEM respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 춘계학술대회 논문집 전자세라믹스 센서 및 박막재료 반도체재료 일렉트렛트 및 응용기술
• /
• pp.147-151
• /
• 2000

This paper presents the electrochemical etch-stop characteristics of single-crystal silicon in a tetramethyl ammonium hyciroxide(TMAH):isopropyl alcohol(IPA):pyrazine solution. Addition of pyrazine to a TMAH:IPA etchant increases the etch-rate of (100) silicon, thus the elapsed time for etch-stop was shortened. The current-voltage(I-V) characteristics of n- and p-type silicon in a TMAH:IPA:pyrazine solution were obtained, respectively. Open circuit potential(OCP) and passivation potential(PP) of n- and p-type silicon, respectively, were obtained and applied potential was selected between n- and p-type silicon PP. The electrochemical etch-stop is applied to the fabrication of 801 microdiaphragms having $20\;{\mu}m$ thickness on a 5-inch silicon wafer. The averge thicknesses of 801 microdiaphragms fabricated on the one wafer were $20.03\;{\mu}m$ and standard deviation was ${\pm}0.26{\mu}m$. The silicon surface of the etch-stopped microdiaphragm was extremely flat without noticeable taper or other nonuniformities. The benefits of the electrochemical etch-stop in a TMAH:IPA:pyrazine solution become apparent when reproducibility in the microdiaphragm thickness for mass production is considered. These results indicate that the electrochemical etch-stop in a TMAH:IPA:pyrazine solution provides a powerful and versatile alternative process for fabricating high-yield silicon microdiaphragms.