• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.6 no.3
• /
• pp.50-56
• /
• 1992

The coupling coefficient K controls the characteristic behaviors of leakage transformer. The value of coupling coefficient K was obtained from th leakage flux of leakage transformer an ascertained from the variation due to the function of current. Therefore, this paper presented the equivalent circuit of leakage transformer consisting of Thevenin's constant voltage source and inductor as (1-K2)L2 which were proportional to parameter K. The proposed equivalent circuit verified the validity in designing the leakage transformer because it was in good agreements of the behaviors of ideal transformer (K is 1), leakage transformer (K is 0$\leq$K$\leq$1), inductor (K is 0).

• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.196-197
• /
• 2010

This paper investigates a high performance converter topology for hydrogen gas generation electrolysis system. The proposed converter topology consists of full-bridge inverter, medium frequency transformer, and diode rectifier. Hydrogen gas generation electrolysis process considered in the paper is analyzed and characterized by its equivalent circuit. The electrolysis cell is modeled as effective resistance, capacitance, inductance, and internal emf voltage source. The proposed converter topology provides enhanced efficiency of hydrogen gas generation process under the operating condition of dc output voltage with high frequency ripple on it. The high performance operation of proposed converter is confirmed through the simulation with the electrolysis cell considered in the equivalent circuit model.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.12
• /
• pp.12-20
• /
• 1998

The non-uniform leaky wave structure of the slits in a parallel-plate waveguide is analyzed from the viewpoints of transmitting(receiving) leaky wave antenna and grating coupler. Period and slit width are simultaneously varied along the leaky wave structure to construct the leaky wave structure with a specific distribution of complex propagation constant. Some results for the equivalent magnetic current distributions over the slits and the radiation characteristics of the leaky wave structure with various source(equivalent magnetic current) distributions such as Gaussian, uniform, cosine, cosine-squared, and Taylor distributions are given and compared with each other.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.14 no.3
• /
• pp.6-11
• /
• 1977

The noise behavior of the Schottky Barrier Gate FET has been investigated by the use of noise equivalent circuit. It has been found that an additional noise source has to be taken into account in the GaAs SBGFET's biased in the pinch-off region; the intervalley scattering noise and the hot electron noise. In this paper, a noise equivalent circuit has been used to determine the noise parameter which was taken into account influence of the saturation velocity of carrier and parasitic resistance.

• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.32-35
• /
• 1996

This paper analyzes characteristics of PMLSM using 3 dimensional equivalent magnetic circuit network method (3-D EMC). PMLSM of which the effective electric-airgap is not only very large, but also the width is finite width lateral edges has much leakage flux. Therefore, 2-D analysis method cannot consider it so carefully that 3-D analysis method must required. 3-D EMC which will be used for analysis of PMLSM performs modeling of it including solt and teeth structure, uses the magnetic motive force of stator winding and permanent magnet as source. and calculates magnetic flux density and force considering nonlinear characteristics of materials. we verified analysis validity by comparing simulation results with expermental results.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.1
• /
• pp.42-47
• /
• 2014

The use of BLDC motor in Vehicle and industrial field, it is operated by continuous and intermittent driving. When the intermittent driving is occurred by the rise and fall of temperature repeatedly, it was represented by different characteristics in case of continuous driving. So, it is very important that heat source estimation according to the duty ratio. In this paper, temperature characteristics according to the operating method of BLDCM was calculated by using the thermal equivalent circuit, and the validity of the study was demonstrated as compared to the calculated and experimental results.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.2
• /
• pp.69-74
• /
• 2016

In this study, we proposed an a-IGZO (amorphous In-Ga-Zn-O) TFT (thin-film transistor) with off-planed source/drain structure. Furthermore, two different electrode materials (ITO and Ti) were applied to the source and drain contacts for performance improvement of a-IGZO TFTs. When the ITO with a large work-function and the Ti with a small work-function are applied to drain electrode and source contact, respectively, the electrical performances of a-IGZO TFTs were improved; an increased driving current, a decreased leakage current, a high on-off current ratio, and a reduced subthreshold swing. As a result of gate bias stress test at various temperatures, the off-planed S/D a-IGZO TFTs showed a degradation mechanism due to electron trapping and both devices with ITO-drain or Ti-drain electrode revealed an equivalent instability.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.1
• /
• pp.70-77
• /
• 2005

A new converter to transfer energy from a low-voltage AC current source to a battery is proposed. It is focused to find operational modes of the converter. The low-voltage AC current source is an equivalent of the piezoelectric generator, which converts the mechanical energy to the electric energy. The converter consists of a full-bridge MOSFET rectifier and a MOSFET boost converter in order to make the converter small and efficient. The operational principle and modes of the converter are investigated with the consideration of effects of the parasitic capacitances of MOSFETs and diode. The results are proved with simulation studies using PSIM and Pspice.

• Nuclear Engineering and Technology
• /
• v.31 no.5
• /
• pp.512-521
• /
• 1999

A feasibility study was performed to design an epithermal neutron beam for BNCT using the neutron of 2.45 MeV on the average produced from $^2H(d,n)^3$He reaction induced by plasma focus in the z-pinch instead of the conventional accelerator-based $^3H(d, n)^4$He neutron generator. Flux and spectrum were analyzed to use these neutrons as the neutron source for BNCT. Neutronic characteristics of several candidate materials in this neutron source were investigated Using MCNP Code, and $^7LiF$ ; 40%Al + 60%$AIF_3$, and Pb Were determined as moderator, filter, and reflector in an epithermal neutron beam design for BNCT, respectively. The skin-skull-brain ellipsoidal phantom, which consists of homogeneous regions of skin-, bone-, or brain-equivalent material, was used in order to assess the dosimetric effect in brain. An epithermal neutron beam design for BNCT was proposed by the repeated work with MCNP runs, and the dosimetric properties (AD, AR, ADDR, and Dose Components) calculated within the phantom showed that the neutron beam designed in this work is effective in tumor therapy. If the neutron source flux is high enough using the z-pinch plasma, BNCT using the neutron source produced from $^2H(d,n)^3$He reaction will be very feasible.

• Journal of Sensor Science and Technology
• /
• v.27 no.5
• /
• pp.335-339
• /
• 2018

The optical characteristics of a terahertz (THz) antenna-coupled bolometer (ACB) detector were evaluated using a pulsed quantum cascade laser (QCL) and radiation blackbody sources. We investigated a method for measuring the responsivity and noise-equivalent power (NEP) of the THz detector using two different types of light sources. When using a QCL source with a frequency of 3 THz, the average responsivity of 24 devices was $1.44{\times}10^3V/W$ and the average NEP of those devices was $3.33{\times}10^{-9}W/{\surd}Hz$. The average responsivity and NEP as measured by blackbody source were $1.79{\times}10^5V/W$ and $6.51{\times}10^{-11}W/{\surd}Hz$, respectively, with the measured values varying depending on the light source. This was because the output power of each light source was different, with the laser source being driven by a pulse type wave and the blackbody source being driven by a continuous wave. The power input to the THz sensor was also different. Futhermore, the responsivity and NEP values measured using band pass filter (BPF) were similar to those measured when using only THz windows. It was found that ACB sensor responds normally in the THz region to both the laser and the blackbody source, and the method was confirmed to effectively evaluate the characteristics of the THz sensor.