• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.957-959
• /
• 2005

A noise reduction equipment in power systems was device combined in a passive element such as the form of L, R and C. A analysis of frequency characteristics for the transformer models shall be considered the additional capacitance between the windings($C_{ps}$), terminals($C_s$), and winding-ground($C_g$). A noise in transformer is modeled by take account into the different frequency. In case of the high frequency, transformer windings with stray capacitance have lower impedance. Therefore a noise is transferred from primary winding to secondary winding. Noise Cut Transformer(NCT) was the noise reduction device and was normally single phase two-winding type transformer. We analyzed frequency characteristics using the nodal network analysis with the equivalent circuit and the simulation of the MATLAB.

• Journal of Biomedical Engineering Research
• /
• v.17 no.4
• /
• pp.535-544
• /
• 1996

In this paper, we analyzed the coil-magnet type vibrating transducer for the implantable middle ear hearing aid which is appropriate for patient's hearing level, and an experimental transducer system is designed For the objective and quantitative analysis of the transducer, a theoretical equivalent model containing coil, magneto and inner ear is developed To perform effective evaluation of the transducer, a transforming ratio Tr is introduced and its range that is suitable for practical implantable middle ear hearing device is foun4 The result of applying physical parameters of ear system to the proposed analytical model shows that frequency response of the coil magrlet type vibrator is predominantly governed by resistive impedance of the coil rather than inertia effect of the magnet and the inner parameters. In addition, we realized an experimental middle ear hearing aid system to show the theoretical validity of designed system and this will provide the basis of the development for actually implantable system.

• Proceedings of the KIPE Conference
• /
• 2015.11a
• /
• pp.99-100
• /
• 2015

본 논문은 Hybrid Electric Vehicle용 리튬이온배터리의 ECM (Equivalent Circuit Model) 선정 방법을 제안한다. 전기 회로를 구성하는 성분들의 특징을 분석하고, 그 결과와 EIS (Electrochemical Impedance Spectroscopy) 장비의 측정 결과를 참고하여 배터리를 모델링한다. 다양한 종류의 배터리에 이 방법을 적용하여 각 배터리에 적합한 ECM을 선정하고, 그 임피던스를 EIS 측정 결과에 비교하여 타당성을 검증한다. 또한, 기존에 제시된 ECM과 비교하여 정확도 개선을 평가한다.

• Proceedings of the KIPE Conference
• /
• 2010.11a
• /
• pp.226-227
• /
• 2010

슈퍼커패시터의 성능을 시험하기 위해 필요한 기존의 실험방법들에는 충방전을 통한 커패시턴스의 측정, AC 임피던스 법에 의한 등가직렬저항(ESR)의 측정 및 자연방전의 측정 등이 포함되는데, 이러한 방법들은 번거롭고 많은 시간을 소요하므로 대량 생산되는 슈퍼커패시터의 모든 셀의 특성을 파악하는데 사용하기는 곤란하다. 따라서 본 논문에서는 전기화학적 임피던스 분광법에 의해 슈퍼커패시터의 등가 임피던스 모델의 파라미터를 추출하고 이를 이용하여 슈퍼커패시터의 제반 특성들을 간접적으로 파악함으로써, 번거로운 여러 가지 실험 없이 전기화학적 임피던스 분광법만으로 슈퍼커패시터의 성능을 판별할 수 있는 새로운 방식을 제안한다.

• Korean Journal of Metals and Materials
• /
• v.50 no.5
• /
• pp.389-393
• /
• 2012

Improvement in microwave absorbance has been investigated by insertion of a periodic air cavity in rubber composites filled with magnetic powders. A mixture of $Co_2Z$ hexagonal ferrite and Fe powders were used as the absorbent fillers in silicone rubber matrix. The complex permeability and complex permittivity of the magnetic composites were measured by reflection/transmission technique. In the grid-type magnetic absorbers, the equivalent permeability (${\mu}_{eq}$) and permittivity (${\varepsilon}_{eq}$) are calculated as a function of air volume rate (K) on the basis of effective medium theory. Reduction in the material parameters (especially, dielectric permittivity and magnetic loss) has been estimated with the increase of K. Plotting the ${\mu}_{eq}$ and ${\varepsilon}_{eq}$ on the solution map of wave-impedance matching, wide bandwidth microwave absorbance has been predicted in the magnetic composites with an optimum value of K.

• Bulletin of the Korean Chemical Society
• /
• v.10 no.6
• /
• pp.495-500
• /
• 1989

The ionic conductivity of polycrystalline, glass, and glass-ceramic silicates was measured using two-terminal AC method with blocking electrode over a frequency range of 100 Hz to 100 KHz in the temperature range of $200^{\circ}C$ to $320^{\circ}C$. Analysing the capacitance (C), susceptance (B), impedance (Z), and conductance (G) under the given conditions, an equivalent circuit containing temperature and frequency dependent component is proposed. Higher capacitance could be observed in the low frequency region and on the improved ionic migration conditions i.e., at higher temperature in a better ionic conductor. Also the electrode polarization built up at the electrode-specimen interface could be sorted out above 10 KHz. However, grain boundary contribution couldn't be extracted from the bulk resistance over the frequency range measured here.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.358-359
• /
• 2019

철교나 석유비축기지 탱크저판 및 각종 매설관로 등 대부분 철 성분 골조는 시간이 경과하면 주변의 환경에 따라 부식이 급격히 일어난다. 이러한 철강재가 부식되는 철강재가 시설물의 주요 구성물이 되고 있는 시설물의 수명을 크게 단축시키는 주요원인이 되고 있다. 이에 대한 대비책으로 방청도료나 코팅을 이용하는 방법과 달리, 전기적으로 전위차를 같게 하여 부식을 방지하는 전기방식법을 적용함에 있어 방식전류가 불균일한 경우 양극 소모가 불균일함에 따라 교체시기 문제를 극복하기 위해 회로 등가 임피던스 추정 및 RF 릴레이 장착한 TB를 이용한 방식전류제어장치를 개발하였다.

• Journal of Aerospace System Engineering
• /
• v.14 no.6
• /
• pp.79-84
• /
• 2020

Cooler driver electronics (CDE) for maintaining low temperature of the satellite payload IR sensor consists of a compressor that has a pulsation current load condition when it is operated. This pulsation current produces large voltage fluctuation, which affects both load and regulated bus stability. Thus, CDE power conditioning system consists of a primary bus, infrared power distribution unit for battery charging and protection, reverse current protection diode, and battery, which is used as a buffer. In this study, the operational mode analysis is performed by each part with equivalent impedance modeling verified through system level simulation. From this mode analysis, the safety margin for state of charge and open circuit voltage of the battery is determined for satisfying the minimum operational voltage of the CDE load.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.1
• /
• pp.36-45
• /
• 2010

In this paper, we propose a new design method to design a wireless power transfer system using loop antennas for consumer electronics. This method can simply design a wireless power transfer system only using measurements of coupling coefficients and simple equations of equivalent circuit model about loop antennas without complicated electromagnetic analysis. Using the proposed design method, a wireless power transfer system with a pair of loop antennas operating at the frequency of 13.56 MHz, which have a dimension of $50{\times}50\;cm^2$, is designed and implemented. The input return loss, coupling coefficient, efficiency, and input impedance variation with respect to a distance between loop antennas were measured. The proposed design method provides good agreements between measured and predicted results. Also, the wireless power transfer system with impedance matching circuits designed by the proposed design method shows two times higher efficiency characteristics than the case with the general $50\;{\Omega}$ impedance matching circuits. Therefore, we verified that our design method could be an effective tool to design a wireless power transfer system.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.4
• /
• pp.10-18
• /
• 2018

The primary purposes of this study are to understand a fundamental aspect of current uniformity around a reinforcing bar (rebar) in cement mortar, and to develop an accurate monitoring method in a wet-dry cycling process with the alternative current (AC) impedance method. Three cement mortar specimens with two embedded rebars were prepared in the laboratory. As a main variable, the distance between two rebars was designed to be 10, 20 and 30 mm with the same thickness of 20 mm. To simulate the corrosion of rebars in concrete structures in a marine environment, three cement mortar specimens were exposed to 15 wet-drying cycles (24-hour-immersion in seawater and 48-hour-drying in a room temperature) in the laboratory. It was observed that the potential level shifted to a noble value during corrosion potential monitoring, which is attributed to acceleration of dissolved oxygen diffusion at the drying process. AC impedance was measured in a frequency range from 100 kHz to 1 mHz on a wet-drying process. A theoretical model was proposed to explain the interface condition between the rebars and cement mortar by using the equivalent circuit consisting of a solution resistance, a charge transfer resistance and a CPE (constant phase element). It was observed that the diffusion impedance appeared in a low frequency range as corrosion of rebars progresses. At the drying stage of the wet-drying cycles, the currents line for monitoring tended to be non-uniform at the interface of rebar/mortar, being phase shift, ${\theta}$, close to $-45^{\circ}$.