• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.400-405
• /
• 2011

The total length of Korean urban railways reaches 1,200km. Urban railway used to be installed with ballasted tracks by reason of low cost at the time of construction, slab tracks are now being installed due to the reasons of the improvement in safety, lengthening service life and more economical method in terms of maintenance. The length rate of slab tracks has exceeded 70% of the domestic urban railways with the methods ranging from STEDEF, LVT, ALT, Eidan-type, B2S to RHEDA. This study surveyed the share of domestic slab tracks, and compared and evaluated the input cost at the initial stage by the types of slab tracks. Construction processes have been standardized by the existing design documents and calculated the initial input cost for the length of 1km of a hypothetical straight line. Cost breakdown structure was evaluated as materials cost, construction cost, equipment cost, indirect cost, etc. It is expected that this study will be used in selection & evaluation which is considering the economic feasibility of slab tracks.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.30 no.3
• /
• pp.77-88
• /
• 2012

In this report, we performed the measurements of physical properties of optical discs as a long term preservation electronic recording device and showed how to improve the preservation method of them. We collect the 1,993 optical discs from the archives of the National Archives of Korea and tested various measurements. We used DVDT-SD4 equipment to measure the quality of data, deformation of disc, the various writing strategy and manufacturer derives, which can be happened in optical discs by physical factors. We found that th quality of data are closely related with write strategy between discs and drives. This relation gives us information about data quality in optical discs for long term preservation that can be obtained from the state between empty discs and optical drives before recording. Thus, the initial selection of optimal discs and drives is critical for long term recording data preservation and the data quality after long time preservation will not be much different from that of the initial ones.

• Polymer(Korea)
• /
• v.39 no.3
• /
• pp.441-452
• /
• 2015

Twin-screw kneader is an efficient polymer processing equipment. In this paper, the mixing performance of one novel intermeshing counter-rotating twin-screw kneader with different tip angles of the male rotor is simulated using the mesh superimposition technique (MST). Statistical analysis is carried out for the flow field using particle tracking technique, and distributive mixing performance is evaluated using the residence time distribution and segregation scale, while the dispersive mixing performance is estimated using the parameters such as shear rate, stretching rate and mixing index. The results show that the best distributive mixing performance is achieved when the tip angle is 0o, while the optimal dispersive mixing performance is obtained when the tip angle is 20o. The results in this paper provide a data basis for the selection of parameters and optimization of the performance for the screw rotors.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.5
• /
• pp.9-19
• /
• 2010

Every car manufacturer desires to reduce the new car development time spent in improving the safety, NVH, lightweight, reliability and environment friendly features of the car. Other considerations such as planning, exterior and interior styling, packaging, color, and material selection increase the complexity of the car design process. This paper proposes a personal DDP (Digital Design Process) to utilize the engineering analysis and design/styling software for car design. DDP can be efficiently used by a team of car research center or a studio with small number of engineers, helping ordinary engineers becoming ambidextrous in design as well as engineering applications. The concept model starts from idea sketch, rendering, and 3D surface model with CAS (Computer Aided Styling) to the final safety estimation by using proposed DDP based on engineering technology (CAD, CAE). The concept model proposed a hydrogen fuel cell sports coupe which could be available within next 10 years. The proposed DDP can not only reduce the new car development time but also be adapted into designing of varied products such as aircraft, yacht, electrical equipment and sports gear.

• Journal of Power System Engineering
• /
• v.21 no.3
• /
• pp.60-65
• /
• 2017

A GA is one of the best method to find optimal value in searching area. A GA is driven by probabilistic selection that based on the survival of the fittest. So this algorithm need a huge solving time even if it can be used lots of optimizing problem such as structural design, machine learning, system's identification and so on. This GA's characteristic constrain the program to drive offline. Some studies try to use this algorithm on online or reduce the GA's running time with parallel GA or micro GA. Unfortunately these studies still didn't reduce amount of fitness solving. If the chromosome was imported to the system, it affected system's stability. And when the control system uses online GA, it also doesn't have enough learning time. In this study, try to find stability criterion to reduce the chromosome's affection and find the characteristic of the number of population and generation when GA was driven into the wide searching area.

• Tunnel and Underground Space
• /
• v.15 no.1 s.54
• /
• pp.22-27
• /
• 2005

This paper presents an article explaining a TBM project overall in Norway. The paper which published in Norwegian TBM Tunnelling by Norwegian Soil and Rock Eng. Assoc. in 1998, contains most of the items considered in TBM tunnelling. New powerplants, tunnels and dams have been built at Meraker in Central Norway. A total of 44 km of tunnels with cross sections varying from $7\;m^2\;to\;32\;m^2$ have been excavated in hard rock formation. Tunnel of 10 km with the 3.5 m diameter was excavated by a HP TBM in a year. his project gives the special attention to the TBM drive and equipment selection, including planning, site organization and performance.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.8
• /
• pp.1173-1182
• /
• 2001

Recent noticeable advances of CNC machine tools have considerably improved productivity and precision in manufacturing processes. However, in the respect of productivity some defects still remain because selection of machining conditions entirely depends on the experiences of programmers. Usually, machining conditions such as feed rate and spindle speed have been selected conservatively by considering the worst cases, and it has brought the loss of machining efficiency. Thus, the improvement of cutting force controller has been done to regulate cutting force constantly and to maximize feedrate simultaneously in case that machining conditions change variously. In this study, sliding mode control with boundary layer is applied to milling process for cutting force regulation and in a commercial CNC machining center data transfer between PC and PMC (programmable machine controller) of CNC machine is done using a standard interface method. And in the cutting force measurement, an indirect cutting force measuring system using current signal of AC servo is adopted in order not to use high-priced equipment like tool dynamometer. The purpose of this study is to maximize the productivity in milling process, thus its results can be applied to cases such as rough cutting process.

• The Korean Journal of Health Service Management
• /
• v.10 no.2
• /
• pp.25-34
• /
• 2016

Objectives : This study was conducted to examine what types of attributes advertising and promotion staff members working at different medical institutes consider when performing their advertising duties. It also seeks to identify satisfaction levels with the advertising conditions and tasks required of them to perform the actual advertising. Methods : This study subjects were members registered in the address book of the Korean Hospital Public Relations Association with 127 actual test respondents targeted. Results : Regarding the selection of the types of advertising message appeals, those with less than five years of work experience were found to prefer emotional messages, whereas those with more than six years of work experience were found to prefer rational messages. male advertising planners preferred rational messages, whereas female advertising planners preferred emotional messages. Conclusions : The medical advertising facilities at hospitals and equipment to produce the main materials to improve the effectiveness of advertising should be considered.

• Proceedings of the KIEE Conference
• /
• 2005.05a
• /
• pp.203-205
• /
• 2005

A reactor protection system (RPS) plays the roles of generating the reactor trip signal and the engineered safety features (ESF) actuation signal when the monitored plant processes reach predefined limits. A Korean project group is developing a new digitalized RPS and the Cabinet Operator Module (COM) of the RPS which is used for the RPS integrity testing and monitoring by an equipment operator. A flat panel display (FPD) with a touch screen capability is provided as a main user interface for the RPS operation. To support the RPS COM user interface design, actually the FPD screen design, we developed a user interface style guide because the system designer could not properly deal with the many general human factors design guidelines. To develop the user interface style guide, various design guideline gatherings, a walk-though with a video recorder, guideline selection with respect to user interface design elements, determination of the properties of the design elements, discussion with the system designers, and a conversion of the properties into a screen design were carried out. This paper describes the process in detail and the findings in the course of the style guide development.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1343-1346
• /
• 2005

In the cold rolling mill, coil breakage that generated in rolling process makes the various types of troubles such as the degradation of productivity and the damage of equipment. Recent researches were done by the mechanical analysis such as the analysis of roll chattering or strip inclining and the prevention of breakage that detects the crack of coil. But they could cover some kind of breakages. The prediction of Coil breakage was very complicated and occurred rarely. We propose to build effective prediction modes for coil breakage in rolling process, based on data mining model. We proposed three prediction models for coil breakage: (1) decision tree based model, (2) regression based model and (3) neural network based model. To reduce model parameters, we selected important variables related to the occurrence of coil breakage from the attributes of coil setup by using the methods such as decision tree, variable selection and the choice of domain experts. We developed these prediction models and chose the best model among them using SEMMA process that proposed in SAS E-miner environment. We estimated model accuracy by scoring the prediction model with the posterior probability. We also have developed a software tool to analyze the data and generate the proposed prediction models either automatically and in a user-driven manner. It also has an effective visualization feature that is based on PCA (Principle Component Analysis).