• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• Asia pacific journal of information systems
• /
• 제22권3호
• /
• pp.99-124
• /
• 2012

Our society has long been talking about necessity for innovation. Since companies in particular need to carry out business innovation in their overall processes, they have attempted to apply many innovation factors on sites and become to pay more attention to their innovation. In order to achieve this goal, companies has applied various information technologies (IT) on sites as a means of innovation, and consequently IT have been greatly developed. It is natural for the field of IT to have faced another revolution which is called cloud computing, which is expected to result in innovative changes in software application via the Internet, data storing, the use of devices, and their operations. As a vehicle of innovation, cloud computing is expected to lead the changes and advancement of our society and the business world. Although many scholars have researched on a variety of topics regarding the innovation via IT, few studies have dealt with the issue of could computing as IT. Thus, the purpose of this paper is to set the variables of innovation attributes based on the previous articles as the characteristic variables and clarify how these variables affect "Performance Expectancy" of companies and the intention of using cloud computing. The result from the analysis of data collected in this study is as follows. The study utilized a research model developed on the innovation diffusion theory to identify influences on the adaptation and spreading IT for cloud computing services. Second, this study summarized the characteristics of cloud computing services as a new concept that introduces innovation at its early stage of adaptation for companies. Third, a theoretical model is provided that relates to the future innovation by suggesting variables for innovation characteristics to adopt cloud computing services. Finally, this study identified the factors affecting expectation and the intention to use the cloud computing service for the companies that consider adopting the cloud computing service. As the parameter and dependent variable respectively, the study deploys the independent variables that are aligned with the characteristics of the cloud computing services based on the innovation diffusion model, and utilizes the expectation for performance and Intention to Use based on the UTAUT theory. Independent variables for the research model include Relative Advantage, Complexity, Compatibility, Cost Saving, Trialability, and Observability. In addition, 'Acceptance for Adaptation' is applied as an adjustment variable to verify the influences on the expected performances from the cloud computing service. The validity of the research model was secured by performing factor analysis and reliability analysis. After confirmatory factor analysis is conducted using AMOS 7.0, the 20 hypotheses are verified through the analysis of the structural equation model, accepting 12 hypotheses among 20. For example, Relative Advantage turned out to have the positive effect both on Individual Performance and on Strategic Performance from the verification of hypothesis, while it showed meaningful correlation to affect Intention to Use directly. This indicates that many articles on the diffusion related Relative Advantage as the most important factor to predict the rate to accept innovation. From the viewpoint of the influence on Performance Expectancy among Compatibility and Cost Saving, Compatibility has the positive effect on both Individual Performance and on Strategic Performance, while it showed meaningful correlation with Intention to Use. However, the topic of the cloud computing service has become a strategic issue for adoption in companies, Cost Saving turns out to affect Individual Performance without a significant influence on Intention to Use. This indicates that companies expect practical performances such as time and cost saving and financial improvements through the adoption of the cloud computing service in the environment of the budget squeezing from the global economic crisis from 2008. Likewise, this positively affects the strategic performance in companies. In terms of effects, Trialability is proved to give no effects on Performance Expectancy. This indicates that the participants of the survey are willing to afford the risk from the high uncertainty caused by innovation, because they positively pursue information about new ideas as innovators and early adopter. In addition, they believe it is unnecessary to test the cloud computing service before the adoption, because there are various types of the cloud computing service. However, Observability positively affected both Individual Performance and Strategic Performance. It also showed meaningful correlation with Intention to Use. From the analysis of the direct effects on Intention to Use by innovative characteristics for the cloud computing service except the parameters, the innovative characteristics for the cloud computing service showed the positive influence on Relative Advantage, Compatibility and Observability while Complexity, Cost saving and the likelihood for the attempt did not affect Intention to Use. While the practical verification that was believed to be the most important factor on Performance Expectancy by characteristics for cloud computing service, Relative Advantage, Compatibility and Observability showed significant correlation with the various causes and effect analysis. Cost Saving showed a significant relation with Strategic Performance in companies, which indicates that the cost to build and operate IT is the burden of the management. Thus, the cloud computing service reflected the expectation as an alternative to reduce the investment and operational cost for IT infrastructure due to the recent economic crisis. The cloud computing service is not pervasive in the business world, but it is rapidly spreading all over the world, because of its inherited merits and benefits. Moreover, results of this research regarding the diffusion innovation are more or less different from those of the existing articles. This seems to be caused by the fact that the cloud computing service has a strong innovative factor that results in a new paradigm shift while most IT that are based on the theory of innovation diffusion are limited to companies and organizations. In addition, the participants in this study are believed to play an important role as innovators and early adapters to introduce the cloud computing service and to have competency to afford higher uncertainty for innovation. In conclusion, the introduction of the cloud computing service is a critical issue in the business world.

• 수산해양기술연구
• /
• 제40권4호
• /
• pp.268-281
• /
• 2004

본 연구는 실제 정치망 어장에서의 조류에 따른 어구 형상 변형을 추정하고, 그 변형을 최소화시키며 어구의 기본 기능을 유지시키는데 필요한 수중 현상과 어구 내부용적을 적절하게 유지할 수 있는 설계의 기본 자료를 얻기 위한 목적으로 회류 수조에서 모형실험을 실시하였으며, 흐름에 따른 대뜸의 멍줄에 작용하는 장력, 정치망 내의 유속변화와 그물형상의 변화를 측정하였다. 1. 유속이 0.0m/s에서 0.6m/s로 증가 할 때에 유속 (v)에 따른 장력(R)의 실험식은 운동장 조상의 경우 R=$19.58v^{1.98}$($r^2$=0.98) 원통 조상인 경우, R=$26.90v^{1.72}$($r^2$=0.95)이었다. 2. 유속변화는 흐름이 망내부를 통과함에 따라 감소하여 운동장이 조상인 경우, 제1원통내부에서 0.1m/s일 때 약 70%, 0.2m/s일 때 60%, 0.3m/s일 때 약 50%, 0.4~0.6m/s에서는 약 40%정도로 초기유속에 비해 감소하였다. 원통이 조상측일 경우, 제2원통을 통과한 흐름은 초기 유속의 약 30~60%로 급격히 감소하였고, 제1원통에서는 약 20~30% 비탈그물에서는 약 10~20%정도 감소하였고, 운동장내에서 다시 유속이 증가하였다. 3. 운동장이 흐름의 조상측인 경우, 운동장그물의 기울기 변화량은 0~70$^{\circ}$까지, 비탈그물은 0~63$^{\circ}$까지 변화하였고, 조하측인 제2원통은 0~47$^{\circ}$까지 변화하였다. 유속이 증가함에 따른 까래그물의 깊이 변화는 초기 깊이에 보다 제1원통과 제2원통이 약 0~45%정도, 비탈그물이 약 0~37% 정도로 감소하였다. 4. 원통이 흐름의 조상측인 경우, 제2원통의 기울기 변화량은 약 0~70$^{\circ}$까지, 비탈그물은 약 0~55$^{\circ}$까지, 조하측인 운동장은 0~50$^{\circ}$까지 였다. 까래그물의 깊이 변화는 초기 깊이와 비교해서 제1원통은 약 0~35%, 제2원통은 약 0~20%, 비탈그물은 약 0~35%까지 감소하였으며, 유속이 0.5m/s이상에서 비탈그물이 원통 입구까지 부상하여, 원통 입구를 90%이상 막았다. 5. 어구의 변형을 최소화하고 전개용적을 증가시키기 위해서는 입구 및 운동장 부분에서는 힘출의 저조시 수심 위치에 중량추를 부착하고, 운동장 바깥쪽과 제1원통의 섶장과 까래그물 제2원통의 바깥쪽, 비탈그물의 까래에 부가 중량추를 부착하는 것이 필요할 것으로 판단된다.

• Asia pacific journal of information systems
• /
• 제20권1호
• /
• pp.141-170
• /
• 2010

User created content (UCC) is created and shared by common users on line. From the user's perspective, the increase of UCCs has led to an expansion of alternative means of communications, while from the business perspective UCCs have formed an environment in which an abundant amount of new contents can be produced. Despite outward quantitative growth, however, many aspects of UCCs do not meet the expectations of general users in terms of quality, and this can be observed through pirated contents and user-copied contents. The purpose of this research is to investigate effective methods for fostering production of creative user-generated content. This study proposes two core elements, namely, reward and motivation, which are believed to enhance content creativity as well as the mediating factor and users' committement, which will be effective for bridging the increasing motivation and content creativity. Based on this perspective, this research takes an in-depth look at issues related to constructing the dimensions of reward and motivation in UCC services for creative content product, which are identified in three phases. First, three dimensions of rewards have been proposed: task dimension, social dimension, and organizational dimention. The task dimension rewards are related to the inherent characteristics of a task such as writing blog articles and pasting photos. Four concrete ways of providing task-related rewards in UCC environments are suggested in this study, which include skill variety, task significance, task identity, and autonomy. The social dimensioni rewards are related to the connected relationships among users. The organizational dimension consists of monetary payoff and recognition from others. Second, the two types of motivations are suggested to be affected by the diverse rewards schemes: intrinsic motivation and extrinsic motivation. Intrinsic motivation occurs when people create new UCC contents for its' own sake, whereas extrinsic motivation occurs when people create new contents for other purposes such as fame and money. Third, commitments are suggested to work as important mediating variables between motivation and content creativity. We believe commitments are especially important in online environments because they have been found to exert stronger impacts on the Internet users than other relevant factors do. Two types of commitments are suggested in this study: emotional commitment and continuity commitment. Finally, content creativity is proposed as the final dependent variable in this study. We provide a systematic method to measure the creativity of UCC content based on the prior studies in creativity measurement. The method includes expert evaluation of blog pages posted by the Internet users. In order to test the theoretical model of our study, 133 active blog users were recruited to participate in a group discussion as well as a survey. They were asked to fill out a questionnaire on their commitment, motivation and rewards of creating UCC contents. At the same time, their creativity was measured by independent experts using Torrance Tests of Creative Thinking. Finally, two independent users visited the study participants' blog pages and evaluated their content creativity using the Creative Products Semantic Scale. All the data were compiled and analyzed through structural equation modeling. We first conducted a confirmatory factor analysis to validate the measurement model of our research. It was found that measures used in our study satisfied the requirement of reliability, convergent validity as well as discriminant validity. Given the fact that our measurement model is valid and reliable, we proceeded to conduct a structural model analysis. The results indicated that all the variables in our model had higher than necessary explanatory powers in terms of R-square values. The study results identified several important reward shemes. First of all, skill variety, task importance, task identity, and automony were all found to have significant influences on the intrinsic motivation of creating UCC contents. Also, the relationship with other users was found to have strong influences upon both intrinsic and extrinsic motivation. Finally, the opportunity to get recognition for their UCC work was found to have a significant impact on the extrinsic motivation of UCC users. However, different from our expectation, monetary compensation was found not to have a significant impact on the extrinsic motivation. It was also found that commitment was an important mediating factor in UCC environment between motivation and content creativity. A more fully mediating model was found to have the highest explanation power compared to no-mediation or partially mediated models. This paper ends with implications of the study results. First, from the theoretical perspective this study proposes and empirically validates the commitment as an important mediating factor between motivation and content creativity. This result reflects the characteristics of online environment in which the UCC creation activities occur voluntarily. Second, from the practical perspective this study proposes several concrete reward factors that are germane to the UCC environment, and their effectiveness to the content creativity is estimated. In addition to the quantitive results of relative importance of the reward factrs, this study also proposes concrete ways to provide the rewards in the UCC environment based on the FGI data that are collected after our participants finish asnwering survey questions. Finally, from the methodological perspective, this study suggests and implements a way to measure the UCC content creativity independently from the content generators' creativity, which can be used later by future research on UCC creativity. In sum, this study proposes and validates important reward features and their relations to the motivation, commitment, and the content creativity in UCC environment, which is believed to be one of the most important factors for the success of UCC and Web 2.0. As such, this study can provide significant theoretical as well as practical bases for fostering creativity in UCC contents.

• 한국산림과학회지
• /
• 제75권1호
• /
• pp.1-18
• /
• 1986

본(本) 연구(硏究)는 굴참나무의 생장인자(生長因子) (흉고직경(胸高直徑), 수고(樹高), 흉고단면적(胸高斷面績) 및 간재적(幹材積))와 삼림환경(森林環境) 및 토양(土壤)의 이화학적(理化學的) 인자(因子)와의 관계(關係)를 분석(分析)하여 임지(林地)의 생산력(生産力)을 추정(推定)하고, 적지선정(適地選定) 기준(基準)을 설정(設定)하는데 그 목적(目的)이 있다. 이 때 고려(考慮)된 인자(因子)는 삼림환경인자(森林環境因子)로 령급(齡級) 외(外) 19개(個) 토양(土壤)의 이화학적(理化學的) 인자(因子)로 토양산도(土壤酸度) 외(外) 11개(個), 총(總) 32개(個) 인자(因子)이다. 경북(慶北)과 충북지방(忠北地方)에서 선정(選定)된 이들 생장인자(生長因子)와 삼림환경인자(森林環境因子)는 99개(個)의 표준지(標準地)를 대상(對象)으로 조사(調査)되었다. 여기에서 채택(採擇)된 인자(因子)는 이산변수(離散變數)와 연속변수(連續變數)이다. 각각의 인자(因子)를 3~4개(個)의 계급(階級)으로 분류(分類)하여, 총(總) 110개(個)의 계급(階級)으로 구분(區分)하였다. 그리고 각 계급(階級)을 별개(別個)의 독립변수(獨立變數)로 하였다. 즉 이는 의사변수(擬似變數)(dummy variable)로 하여 그의 값을 1 혹은 0으로 놓았다. 각 인자(因子)의 첫 계급(階級)은 통계학적(統計學的) 고려(考慮) 때문에 정규방정식(正規方程式)에서 제외(除外)시켰다. 먼저 4개(個)의 굴참나무 생장인자(生長因子)와 110개(個)의 계급(階級)과의 관계(關係)를 회귀분석(回歸分析)하였다. 다음으로 4개(個)의 생장인자(生長因子)와 32개(個)의 독립변수(獨立變數)간의 편상관계수(偏相關係數)를 계산(計算)하였다. 마지막으로 계급간(階級間)의 범위(範圍)를 구(求)하기 위하여 상대점수(相對點數)를 추정(推定)하였다. 이와 같이 통계분석(統計分析)한 결과(結果)를 요약(要約)하면 다음과 같다. 1) 임목생장인자(林木生長因子)와 삼림환경인자(森林環境因子)와의 관계(關係)를 분석(分析)한 결과(結果), 수고(樹高)를 종속변수(從屬變數)로 하는 것이 추정율(推定率)이 가장 높았다. 그러므로 생장인자(生長因子) 중(中) 수고(樹高)를 임지생산력(林地生産力)의 추정기준(推定基準)으로 하는 것이 효율적(効率的)이라 사료(思料)된다. 2) 입목지(立木地)의 생산력(生産力)은 전체(全體) 삼림환경인자(森林環境因子)에 의하여, 그리고 무입목지(無立木地)는 토양(土壤)의 이화학적(理化學的) 인자(因子)에 의하여 추정(推定)할 수 있다. 3) 전체(全體)의 임목생장인자(林木生長因子)에 공통(共通)으로 크게 관여(關與)하는 인자(因子)는 령급(齡級), 유효토탐(有効土探), 임목밀도(林木密度), 모암(母岩), 위도(緯度), 토양습도(土壤濕度) 등으로서, 이들 인자(因子)의 양부(良否)가 곧 적지적수(適地適樹)의 기준(基準)이 될 수 있다. 4) 임목생장(林木生長)에 대한 계급간(階級間)의 상대점수차(相對點數差)가 공통(共通)으로 큰 인자(因子)는 모암(母岩), 위도(緯度), 전질소함량(全窒素含量), 령급(齡級), 유효토탐(有効土探), 토양습도(土壤濕度), 유기질함량(有機質含量) 등으로서 이들 인자(因子)의 계급(階級)에 따라 적지적수(適地適樹)를 선정(選定)하여야 할 것으로 사료(思料)된다.

• 한국사회복지학회:학술대회논문집
• /
• 한국사회복지학회 2003년도 추계학술대회 자료집
• /
• pp.185-216
• /
• 2003

본 연구에서 지체장애근로자들의 직업성공을 구성하는 요인들을 분석하고 이들 요인이 직업성공과 이직에 영향을 미치는 정도를 조사하여 가설적 이론모형을 검증하려는 목적을 두었다. 이를 위해서 지체장애를 가진 근로자 374명과 일반근로자 453명을 대상으로 구조화된 설문지를 통해 나타난 주요 연구결과들은 다음과 같이 요약되었다. 첫째, 장애근로자와 일반근로자의 직업성공을 구성하는 요인은 개인, 가정, 조직의 측면에서 나타났다. 개인적인 측면은 자아존중감과 자아효능감으로 구성되었고, 가족적인 측면은 다중역할스트레스와 자녀의 수로 구성되었다. 조직적인 측면은 자원활용능력, 네트워킹, 그리고 조언자로 구성되었다 이 밖에도 주관적인 직업성공과 객관적인 직업성공이라는 잠재변수에서 종 10개의 측정변수가 도출되었다. 둘째, 장애근로자와 일반근로자 집단 모두 직종이 직업성공에 영향을 미치는 것으로 조사되었다. 관측변수에서는 두 집단에서 직업성공에 영향을 주는 변수가 서로 다르게 나왔다. 장애근로자집단은 이직을 했을 때 평균적으로 근속한 년수와 임금을 제외하고 나머지 모든 관측변수에서 영향을 미치는 것으로 나타났으며, 일반집단은 조언자와 근속년수를 제외하고 나머지 모든 관측변수에서 영향을 미치는 것으로 조사되었다. 셋째, 장애근로자와 일반근로자 집단 모두 연령과 이직 경험이 이직 (이직횟수)에 영향을 미치는 것으로 나타났다. 그러나 장애집단은 친구의 수, 일반집단은 직업선택 시 중요하게 고려하는 사망이 각각 이직에 강한 영향을 미치는 것으로 조사되어 두 집단의 자이를 보여주었다. 또한 관측변수에서도 장애집단은 배우자의 직업과 근속년수, 일반집단은 다중역할 스트레스와 이직평균 근무년수에서 각기 다르게 이직에 영향을 미치는 것으로 나타났다. 넷째, 가설적 경로모형을 검증한 결과 제 1모형은 어느 정도 타당하고 직업성공을 예측할 수 있는 것으로 나타났으며, 제 2모형은 카이스퀘어와 자유도 ($x^2=64950$, df=61, P=0341), 기초부합치 (AGFI)는 .954, 비적합지수 (CFI)는 997, 그리고 원소간의 평균차이 (RMR)도 .038로써 모형의 적합도 지수는 모두 허용된 범위 안에 있기 때문에 매우 적합한 모형으로 직업 성공을 보다 높게 예측할 수 있는 것으로 조사되었다. 이상의 연구결과를 바탕으로 본 연구에서는 다음과 같이 결론을 도출하였다. 첫째, 직종이 두 집단 모두에서 직업성공을 예측하는데 주요한 변수로 나타나 장애근로자들의 학력을 높이고 계속해서 전문화 육에 많은 노력이 필요할 것이다. 특히, 임금정도와 같은 객관적인 직업성공 보다는 임금과 진급에서의 만족과 같은 주관적인 직업성공에 더욱 더 많은 고려를 기울여야 할 것으로 사료된다. 둘째, 장애근로자의 이직을 줄이기 위해서는 직장 내에서 유용한 인적 자원과 네트웍의 수를 늘여야 할 것이다. 이것은 장애집단이 일반집단보다 대인관계에 대해서 더 많은 시간과 노력을 기울여야 한다는 것을 의미한다.

• 한국잠사곤충학회지
• /
• 제9권
• /
• pp.67-87
• /
• 1969

1. 본 조사는 현재 우리나라에 보존되어 있는 계통을 전부 수집하여 Virus병에 대한 저항성을 계통별로 조사함으로써 잠견생산에 막대한 피해를 주는 Virus병에 대하여 저항성이 강한 계통을 선발하는 동시에 선발된 결과는 앞으로 저항성품종 육성제료로 삼고저 하였다. 2. 가잠의 핵형다각체 Virus병에 대하여 저항성이 강한 계통은 N$_4$, N$_{6}$, N$_{46}$, $C_{85}$, E$_{111}$로써 log ED$_{50}$ 값이 0.799~1.611 범위내에 있으며 강한 계통으로서는 N$_{10}$, $C_{62}$, N$_{70}$, N$_{79}$, $C_{106}$이고 log ED$_{50}$의 값은 5.159~7.258 범위내에 있다(표 4참조) 그러고 일본계통이 가장 강하여 log ED$_{50}$이 3.770이 3.770이고 중국계통의 log ED$_{50}$은 3.564로서 다음이고 가주계통의 log ED$_{50}$이 3.381로서 가장 강한 계통으로 나타났다. 감염율의 회귀방정식의 방향계수는 0.1~0.6범위로서 우리나라 보존계통의 저항성의 균일성이 비교적 작을 경향을 다타냈다. ra계통별 저항성의 유전현상에 대한 해명과 품질육성을 위한 구체적인 응용방법에 관한 구명은 차후의 숙제로 남게 되었다. 3. 잠체의 수분 및 회분과 Virus병에 대한 저항성과는 상관관계가 없었고(표 8참조) 다만 감잠비율(보통 사육법에 의하여 조사된 것)과는 고도의 상관관계가 있다. 즉 4면 기잠에서는 수분 및 회분과는 관계가 없었고 3면 기잠에서는 수분은 +0.326 회분은 +0.326으로서 고도의 유의성을 나타냈고 1면과 2면의 회분에서는 각각 +0.520과 ＋386으로서 고도의 유의성을 나타냈으나 수분에서는 유의성이 없었다(표7 참조). 4. 교배조간에 있어서는 기호 205가 모든 형질에 있어서 가장 우수하였다. 특히 204는 강건성이 매우 좋았으나 견질에 있어서 대조구보다 약간 떨어진다. 기호 212는 견질을 약간 떨어지고 감잠비율은 보통이나 수견량이 공시품종중 가장 많았다(표 11). 5. 종합적으로 기술하면 Virus에 대한 저항성이 강한 상기 몇 계통은 강건성 품종？성을 위한 기초자료가 될것이며 계속 여러 계통외 특성을 조사하여 특성 보존을 위한 품종보존의 완벽을 기하여야겠다.다.

• Asia pacific journal of information systems
• /
• 제22권4호
• /
• pp.101-123
• /
• 2012

Currently, Social Media, it has widely a renown keyword and its related social trends and businesses have been fastly applied into various contexts. Social media has become an important research area for scholars interested in online technologies and cyber space and their social impacts. Social media is not only including web-based services but also mobile-based application services that allow people to share various style information and knowledge through online connection. Social media users have tendency to common identity- and bond-attachment through interactions such as 'thumbs up', 'reply note', 'forwarding', which may have driven from various factors and may result in delivering information, sharing knowledge, and specific experiences et al. Even further, almost of all social media sites provide and connect unknown strangers depending on shared interests, political views, or enjoyable activities, and other stuffs incorporating the creation of contents, which provides benefits to users. As fast developing digital devices including smartphone, tablet PC, internet based blogging, and photo and video clips, scholars desperately have began to study regarding diverse issues connecting human beings' motivations and the behavioral results which may be articulated by the format of antecedents as well as consequences related to contents that people create via social media. Social media such as Facebook, Twitter, or Cyworld users are more and more getting close each other and build up their relationships by a different style. In this sense, people use social media as tools for maintain pre-existing network, creating new people socially, and at the same time, explicitly find some business opportunities using personal and unlimited public networks. In terms of theory in explaining this phenomenon, social capital is a concept that describes the benefits one receives from one's relationship with others. Thereby, social media use is closely related to the form and connected of people, which is a bridge that can be able to achieve informational benefits of a heterogeneous network of people and common identity- and bonding-attachment which emphasizes emotional benefits from community members or friend group. Social capital would be resources accumulated through the relationships among people, which can be considered as an investment in social relations with expected returns and may achieve benefits from the greater access to and use of resources embedded in social networks. Social media using for their social capital has vastly been adopted in a cyber world, however, there has been little explaining the phenomenon theoretically how people may take advantages or opportunities through interaction among people, why people may interactively give willingness to help or their answers. The individual consciously express themselves in an online space, so called, common identity- or bonding-attachments. Common-identity attachment is the focus of the weak ties, which are loose connections between individuals who may provide useful information or new perspectives for one another but typically not emotional support, whereas common-bonding attachment is explained that between individuals in tightly-knit, emotionally close relationship such as family and close friends. The common identify- and bonding-attachment are mainly studying on-offline setting, which individual convey an impression to others that are expressed to own interest to others. Thus, individuals expect to meet other people and are trying to behave self-presentation engaging in opposite partners accordingly. As developing social media, individuals are motivated to disclose self-disclosures of open and honest using diverse cues such as verbal and nonverbal and pictorial and video files to their friends as well as passing strangers. Social media context, common identity- and bond-attachment for self-presentation seems different compared with face-to-face context. In the realm of social media, social users look for self-impression by posting text messages, pictures, video files. Under the digital environments, people interact to work, shop, learn, entertain, and be played. Social media provides increasingly the kinds of intention and behavior in online. Typically, identity and bond social capital through self-presentation is the intentional and tangible component of identity. At social media, people try to engage in others via a desired impression, which can maintain through performing coherent and complementary communications including displaying signs, symbols, brands made of digital stuffs(information, interest, pictures, etc,). In marketing area, consumers traditionally show common-identity as they select clothes, hairstyles, automobiles, logos, and so on, to impress others in any given context in a shopping mall or opera. To examine these social capital and attachment, we combined a social capital theory with an attachment theory into our research model. Our research model focuses on the common identity- and bond-attachment how they are formulated through social capitals: cognitive capital, structural capital, relational capital, and individual characteristics. Thus, we examined that individual online kindness, self-rated expertise, and social relation influence to build common identity- and bond-attachment, and the attachment effects make an impact on both the willingness to help, however, common bond seems not to show directly impact on information sharing. As a result, we discover that the social capital and attachment theories are mainly applicable to the context of social media and usage in the individual networks. We collected sample data of 256 who are using social media such as Facebook, Twitter, and Cyworld and analyzed the suggested hypotheses through the Structural Equation Model by AMOS. This study analyzes the direct and indirect relationship between the social network service usage and outcomes. Antecedents of kindness, confidence of knowledge, social relations are significantly affected to the mediators common identity-and bond attachments, however, interestingly, network externality does not impact, which we assumed that a size of network was a negative because group members would not significantly contribute if the members do not intend to actively interact with each other. The mediating variables had a positive effect on toward willingness to help. Further, common identity attachment has stronger significant on shared information.

• 한국심리학회지 : 문화 및 사회문제
• /
• 제12권5호_spc
• /
• pp.45-79
• /
• 2006

필자와 공동연구자들(2002)이 선행연구에서 개발한 주관안녕척도를 사용하여 한국문화에서 주관안녕에 영향을 미치는 변인들을 알아낸 연구 결과들을 개관하고, 국내외 연구들과 비교하여 시사점을 논의하고, 장래 연구할 과제들도 제안하였다. 먼저 주관안녕에 영향을 미치는 선행요인들로 ① 개인차와 인구통계 변인들, ② 개인과정 요인들, ③ 대인과정 요인들 및 ④ 한국문화의 요인으로 사회규범에 따른 행동을 다룬 연구 결과들을 개관했다. 또한 노인을 대상으로 주관안녕이 동시점에서 신체건강의 예측에 기여하는 수준과 아울러 1년 이상이 경과한 시점에서 종단적으로 신체건강이나 생사에 어떤 영향을 미치는지도 알아냈다. 본 논문은 한국문화에서 필자와 공동연구자들이 수행한 실증연구의 결과들과 연결시켜서 주관안녕을 연구하는데 따르는 이론, 방법 및 과제들을 구체적으로 논의함으로써 장차 문화비교 연구와 아울러 국내 연구에 시사점들을 제시한데 의의가 있다.

• 한국수산과학회지
• /
• 제3권3호
• /
• pp.177-186
• /
• 1970

1. 1969년 10월에 전복 Haliotis discus hannai Ino를 재료로 하여 간출 자극에 의한 산란 유발 시험을 실시하여 다량의 수정란을 얻을 수 있었으며 수정율은 1차가 약 $50.0\%$ 2차가 약 $30.0\%$였다. 2. 산란시의 수온은$16.0^{\circ}\~23.0^{\circ}C$내외였으며 사육 수온 $14.0\~18.8^{\circ}C$범위에서 발생 경과시간은 Torcho-phore기(담륜자)까지는 약 22시간, Veliger기(피면자)까지는 약 34시간, 부유 유생기 까지는 $2.5\~3$일이 경과되었으며 7일 경가후부터 부착이 시작되어 9일째는 섬모가 없어지면서 부착이 완료되었다. 이어서 주구각이 생기기 시작하였고, 첫 호수공은 110일만에 생겼다. 3. 10웜 10일에 산란 부화한 유생의 성장크기는 15일만에 0.40mm로 크고, 49일만에 1.39 mm의 포복기 유생으로 자랐다. 첫 호수공은 110일만에 2.14 mm로 큰 후에 생겼으며, 월동이 끝나는 170일 만에는 5.20 inn로 크고 228일만에 10.00 mm로 자랐다. 그 월별 성장은 $L=0.9981\;e^{0.17659M}$의 관계식으로 표시된다. 4. 부유 유생의 사육 밀도는 약 10개/100cc 내외로 하였으며, 부착기는 $30\times20\;cm$ 크기의 굴곡이 있는 플라스틱 판을 사용한 결과 약 $10\~600$개가 부착하였으나 부착 직전에 넣은 것과 저면에 둔 것이 부착율이 양호하였다. 5. 부착 후의 폐사율은 주구각이 형성되는 10일 경과 후는 약 $8\%$가 폐사하였고, 수온이 $10^{\circ}C$로 하강하는 (28일 경과) 때는 $67.9\%$, 제 1호수공이 생기는 (110일 경과) 때는 $79.0\%$, 월동이 끝나는 170일 경과 후는 약 $87.0\%$가 폐사되어 생잔율은 약 $13.0\%$였다. 6. 초기 먹이인 Navicula sp.의 부착 성적은 표면 5cm 하에서는 17일이 경과한 후 $34.3\times10^4/cm^2$개체로 증가하였고 수면 45 cm하에서는 15일만에 $27.2\times10^4/cm^2$ 개체로 증가되었으며 저면인 85 cm하에서는 15일만에 $26.3\times10^4/cm^2$ 개체로 증가되었다. 7. 3.0 mm 크기의 새끼 전복의 1개월간의 전체 이동 저리는 11.36m였으며, $18:00\~21:00$ 사이가 52.2 이동율로서 가장 이동이 심하였다. 8. 2.0mm내외의 전복은 $0^{\circ}\~\;-1.8^{\circ}C$의 수온 범위에서 $16:00\~20:00$시까지는 1.15 cm의 이동이 $0:00\~08:00$시 까지는 0.1cm의 이동이 있었다. 9. 동해안 쪽인 포항 연안파 남해안 쪽인 여수돌산도아 흑산도에서 채집된 전복에 대하여 각장에 대한 과의 관계를 보면 돌산도산 $W=0.2479\;L^{2.5721}$, 흑산도산 $W=0.1001\;L^{3.1021}$, 포항산 $W=0.9632\;L^{2.0611}$의 식으로 표시되었고 해안 쪽의 포항산이 남해안산에 비하여 각장에 대한 체중의 증가가 완만한 것으로 보였다.