• Journal of Korea Water Resources Association
• /
• v.46 no.11
• /
• pp.1041-1052
• /
• 2013

In this study, we estimate parameters of a distributed hydrologic model, GRM (grid based rainfall-runoff model), using a model-independent parameter estimation tool, PEST. We implement auto calibration of model parameters such as initial soil moisture, multipliers of overland roughness and soil hydraulic conductivity in the Geumho River Catchment and the Gamcheon Catchment using radar rainfall estimates and ground-observed rainfall represented by Thiessen interpolation. Automatic calibration is performed by GRM-MP (multiple projects), a modified version of GRM without GUI (graphic user interface) implementation, and "Parallel PEST" to improve estimation efficiency. Although ground rainfall shows similar or higher cumulative amount compared to radar rainfall in the areal average, high spatial variation is found only in radar rainfall. In terms of accuracy of hydrologic simulations, radar rainfall is equivalent or superior to ground rainfall. In the case of radar rainfall, the estimated multiplier of soil hydraulic conductivity is lower than 1, which may be affected by high rainfall intensity of radar rainfall. Other parameters such as initial soil moisture and the multiplier of overland roughness do not show consistent trends in the calibration results. Overall, calibrated parameters show different patterns in radar and ground rainfall, which should be carefully considered in the rainfall-runoff modelling applications using radar rainfall.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.18 no.1
• /
• pp.90-104
• /
• 2015

The purpose of this paper is to build a spatio-temporal evapotranspiration(ET) estimation model using Terra MODIS satellite image and by calibrating with the flux tower ET data from watershed. The fundamentals of spatial ET model, Surface Energy Balance Algorithm for Land(SEBAL) was adopted and modified to estimate the daily ET of Yongdam Dam watershed in South Korea. The daily Normalized Distribution Vegetation Index(NDVI), Albedo, and Land Surface Temperature(LST) from MODIS and the ground measured wind speed and solar radiation data were prepared for 2 years(2012-2013). The SEBAL was calibrated with the forest ET measured by Deokyusan flux tower in the study watershed. Among the model parameters, the important parameters were surface albedo, NDVI and surface roughness in order for momentum transport during calculation of sensible heat flux. As a result of the final calibration, the monthly averaged albedo and NDVI were used because the daily values showed big deviation with unrealistic change. The determination coefficient($R^2$) between SEBAL and flux data was 0.45. The spatial ET reflected the geographical characteristics showing the ET of lowland areas was higher than the highland ET.

• Journal of Advanced Research in Ocean Engineering
• /
• v.2 no.3
• /
• pp.99-111
• /
• 2016

Seabed affected by scouring, sedimentation, and siltation occurrences often cause exposure, which induces risks to existing structures or crude oil or gas pipeline buried subsea. In order to prevent possible risks, more economical structure installation methodology is proposed in this study by predicting and managing the risk. Also, the seabed does not only consist of sandy material, but clayey soil is also widespread, and the effect of undrained shear strength should be considered, and by cyclic environmental load, pore water pressure will occur in the seabed, which reduces shear strength and allows particles to move easily. Based on previous research regarding sedimentation or erosion, the average value of external environmental loads should be applied; for scouring, a 100-year period of environmental conditions should be applied. Also, sedimentation and erosion are mainly categorized by the bed load and suspended load; also, they are calculated as the sum of bed load and suspended load, which can be obtained from the movement of particles caused by sedimentation or erosion.

• Journal of Korean Society of Forest Science
• /
• v.107 no.1
• /
• pp.108-111
• /
• 2018

Increasing soil surface roughness can be effective in enhancing infiltration of rainfall and depression storage capacity of forest soil and reducing surface run-off. In this study, a forest slope with hemispherical depressions shows greater infiltration of water, whereas depression storage capacity is higher in soil with depressions perpendicular to a water flow pathway. Soil pitting or forming surface depressions can be used as a countermeasure after forest fires and a practical way to reduce drought stress of forest soil.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.5
• /
• pp.127-133
• /
• 2015

Recent worldwide trends are to develop the environmental friendly chemicals and processes in order to reduce the global warming and climate change phenomena. One of similar efforts in paper industry is to substitute the petroleum-based SBR latex by starch-based biobinder. The disadvantage of biobinder found through laboratory scale study was the lower dry pick strength than SBR latex. The objective of this study is to confirm the substitutability of SBR latex with biobinder through mill trial. Although biobinder itself gave lower dry pick strength, it was found that the use of SBR latex and biobinder mixture (50:50) could improve the dry pick strength. The introduction of biobinder into coating binder system improved the opacity of coated paper. Optical properties (brightness and whiteness), ink trapping, print gloss and mottling level of paper coated with biobinder system were similar to those of SBR latex.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.6
• /
• pp.63-70
• /
• 2014

Part of SB latex in pre-coating color was substituted with newly developed starch-based bio-binder in order to investigate the effect of starch-based bio-binder in pre-coating color on the properties of coating color and coated paper. Smoothness and gloss of coated paper were decreased with the increase of bio-binder substitution ratio. Brightness and whiteness did not show the significant changes, but stiffness was improved with bio-binder. Ink set-off, dry-pick and wet pick were decreased with the increase of bio-binder substitution ratio. In general, when all SB latex is substituted with bio-binder, ink set-off, dry- and wet-pick were deteriorated. However, it was found that if the bio-binder substitution ratio is controlled below 50%, similar qualities with coated paper manufactured by the use of SB latex binder can be obtained.

• Journal of the Korean Geosynthetics Society
• /
• v.5 no.4
• /
• pp.49-58
• /
• 2006

Recently, geosynthetic clay liners (GCLs) have increasingly been used to replace compacted clay liners (CCLs) in composite liner systems. Since the introduction of GCLs to waste containment facilities, one of the major concerns about their use has been the hydraulic equivalency to CCLs as required by regulations. Laboratory test results and more recently field observations show that the thickness, or mass per unit area, of hydrated bentonite in a GCL can decrease under normal stress, especially around zones of stress concentration or nonuniform stresses, such as a rock or roughness in the subgrade, a leachate sump, or wrinkles in an overlying geomembrane. This paper presents field case histories that confirm the laboratory observations of bentonite migration and the effect of bentonite migration on hydraulic equivalency and contaminant transport through a GCL.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.4
• /
• pp.91-98
• /
• 2012

This study was carried out in order to evaluate the effects of ultra fine precipitated calcium carbonate (UFPCC) on properties of coating color, coated paper and off-set printability. It was found that blending of UFPCC increased the low-shear viscosity and water retention of coating color. The smaller the particle size, the more significant the effect of it. When the blending ratio of UFPCC was increased, brightness, whiteness and opacity of the coated paper were improved, while paper gloss was decreased due to the increase in roughness. When the UFPCC with the average particle size of $0.12{\mu}m$ was used, the ink receptivity during off-set printing was improved while print gloss was maintained or a little decreased. It was also observed that the dry-pick and wet-pick strength of coated paper were improved by the use of UFPCC. In conclusion, it is possible to produce the low gloss matt paper with the use of UFPCC since it could improve the optical properties and ink receptivity of coated paper.

• Journal of Korean Society on Water Environment
• /
• v.26 no.2
• /
• pp.289-296
• /
• 2010

The purpose of this study is to evaluate various pre-treatment methods and proprieties of water quality for wastewater reuse using reverse osmosis (RO) processes. Secondary effluents were sampled from wastewater treatment plants and lab scale pre-treatments and RO filtration test were conducted systematically. Specifically, different types of pre-treatments, such as coagulation, microfiltration and ultrafiltration, were employed to evaluate the removal efficiency of particle and organic matters which may affect the membrane fouling rate. RO process was later added to eliminate trace amounts of remaining organic matters and salt from the raw water for wastewater reclamation. The permeate through the RO process satisfied water quality regulations for industrial water uses. The experimental results showed that the initial fouling tendency differed not only by the feed water properties but also by the membrane characteristics. Membrane fouling was greater for the membranes with large surface roughness, regardless of the hydrophobicity and zeta potentials. Thus both careful consideration of pre-treatment options and proper selection of RO membrane are of paramount importance for an efficient operation of wastewater treatment.

• Steel and Composite Structures
• /
• v.37 no.3
• /
• pp.291-306
• /
• 2020

The noise from the elevated lines of rail transit has become a growing problem. This paper presents a new method for the rapid prediction of the structure-borne noise from steel or composite bridges, based on the receptance and Statistical Energy Analysis (SEA), which is essential to the study of the generation mechanism and the design of a low-noise bridge. First, the vertical track-bridge coupled vibration equations in the frequency domain are constructed by simplifying the rail and the bridge as an infinite Timoshenko beam and a finite Euler-Bernoulli beam respectively. Second, all wheel/rail forces acting upon the track are computed by taking a moving wheel-rail roughness spectrum as the excitation to the train-track-bridge system. The displacements of rail and bridge are obtained by substituting wheel/rail forces into the track-bridge coupled vibration equations, and all spring forces on the bridge are calculated by multiplying the stiffness by the deformation of each spring. Then, the input power to the bridge in the SEA model is derived from spring forces and the bridge receptance. The vibration response of the bridge is derived from the solution to the power balance equations of the bridge, and then the structure-borne noise from the bridge is obtained. Finally, a tri-span continuous steel-concrete composite bridge is taken as a numerical example, and the theoretical calculations in terms of the vibration and noise induced by a passing train agree well with the field measurements, verifying the method. The influence of various factors on wheel/rail and spring forces is investigated to simplify the train-track-bridge interaction calculation for predicting the vibration and noise from steel or composite bridges.