• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.6 no.1
• /
• pp.17-27
• /
• 1996

This study was designed to survey exposure levels of formaldehyde among workplaces in some plywood industries and to compare three sampling methods including the impinger method(IM, NIOSH method No. 3500), the solid sorbent tube method(SS, NIOSH method No. 2541), and the passive bubbler monitor method(PB, SKC). The survey was conducted in seven particle board manufacturing factories, two resin manufacturing factories and two plywood manufacturing factories in Incheon area during the period from March 6 to April 20, 1995. The workplaces included were the hot/cold press, the roller/spreader, the soaking/drying, and the reaction/mixing areas. The results were as follows; 1. The average(GM, GSD) concentrations of formaldehyde by sampling methods were 0.11(4.43) ppm by IM, 0.27(2.03) ppm by SS, and 0.29(2.04) ppm by PB, respectively. The concentrations by 1M method were statistically very significantly lower than those of SS and PB methods, particularly at low air borne concentrations of formaldehyde (p<0.001). 2. The area average concentrations of formaldehyde by workplaces measured with PB bubblers were 0.23(2.08) ppm from the press, 0.23(1.77) ppm from the spreader, 0.24(1.51) ppm from the soaking, and 0.46(1.96) ppm from the reaction areas, respectively. The personal average concentrations of formaldehyde by workplaces measured with PB bubblers were 0.30(1.77) ppm from the press, 0.33(1.54) ppm from the spreader, 0.36(1.46) ppm from the soaking, and 0.84(1.19) ppm from the reaction areas, respectively. 3. No statistically significant differences of formaldehyde concentrations among workplaces except the reaction area(p<0.001) were found. 4. Formaldehyde concentrations from personal samples were higher than those of from area sam pies in all workplaces studied. But no statistically significant differences of formaldehyde concentrations both area and personal samples were found. In conclusion, this study found that although formaldehyde concentrations in some plywood industries in Incheon area were below the regulatory limit of 1 ppm, they were over the limits recommended by NIOSH and ACGIH. This study also suggests that the impinger method may underestimate true formaldehyde concentrations. It implies that there will be more workplaces not meeting current regulatory limit if either the solid sorbent or passive bubbler methods were used instead of the impinger method. It is suggested that passive monitors will be a reasonable alternative for area and personal sampling of formaldehyde if the accuracy and validity of passive monitors be verified before use.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.18 no.4
• /
• pp.310-317
• /
• 2008

The objective of the survey is to define and judge exposure profiles semi-qualitative data in high risk processes using styrene. The survey was conducted on 98 factories out of 229 factories based on data from periodic working environment monitoring for styrene. Styrene is widely utilized as a raw material for PS and co-polymers such as ABS, SAN, SBR, SBL, unsaturated polyester resins(UPR) and others. An approximate breakdown of styrene's markets in Korea is PS 30%, expandable PS 17%, ABS 33%, SAN 5%, SBL 4%, SBR 3%, UPR 1% and other 7%. Although UPR accounts for 1% of total amount of styrene, workers dealing with it are exposed to very high concentrations up to 64 ppm. Especially styrene is widely used in the laminating process of fiberglass reinforced plastics(FRP) manufacturing industry. The Applications using styrene are largely classified into two sections which are applied to styrene monomer(SM) and UPR. SM is utilized for a raw material of resins, surfactant and adhesive. UPR is employed for FRP and non-FRP. For SM control targets are mixing colors and packing in the gelcoat resins manufacturing industry(MI), for UPR control targets out of works using UPR are 1) laminating in the MI of plastics, automobile parts and boats, 2) mixing and packing in the SMC/BMC MI, 3) molding and cutting in the other specific plastics MI, 4) mixing and coating in artificial marble product MI, 5) dipping in the electric motors & transformers MI, 6) molding in the button MI, 7) painting in the musical instrument MI. Findings from the study have given the information for the high risk processes and working practices so that occupational health professionals could focus on targeted workplaces to prevent occupational diseases. It is also useful to develop a control strategies and specific controls for high risk processes and facilities using styrene.

• Journal of Korean Society of Transportation
• /
• v.34 no.5
• /
• pp.377-393
• /
• 2016

Vehicle emissions have been known as a critical factor to give a negative impact on the public health. In particular, particulate matters(PM) and NOx are highly related with respiratory diseases such as asthma. This study aimed at analyzing spatio-temporal patterns of PM and NOx generated from urban freeway traffic. MOVES, which is a well-known emission analysis tool presented by US Environmental Protection Agency(EPA), was applied to estimate PM and NOx based on traffic volume and speed data obtained from Seoul Outer Ring Expressway during January~June, 2012. K-means clustering analysis was used for categorizing the Level of Vehicle Emissions(LOVE) to support more systematical identification of the significance of emissions. Then, spatio-temporal analyses of estimated emissions were conducted by LOVE. Finally, this study proposed a set of strategies to reduce both PM and NOx to enhance public health based on analysis results.

• Toxicological Research
• /
• v.23 no.2
• /
• pp.151-158
• /
• 2007

tert-Butyl acetate is an organic solvent used for coatings, industrial cleaning, and surface treatment applications. This study investigated the potential adverse effects of tert-butyl acetate on pregnant dams and embryo-fetal development after maternal exposure on gestational days 6 through 19 in rats. The test chemical was administered to pregnant rats by gavage at dose levels of 0, 500, 1,000, 1,500, and 2,000 mg/kg/day. All dams were subjected to a caesarean section on day 20 of gestation and their fetuses were examined for any external, visceral, and skeletal abnormalities. At 2,000 mg/kg, treatment-related clinical signs, including piloerection, abnormal gait, decreased locomotor activity, loss of fur, reddish tear, anorexia, nasal discharge, vocalization and coma, were observed in a dose-dependent manner. All dams died between the 2nd day and 5th day of treatment due to a severe systemic toxicity. At 1,500 mg/kg, minimal maternal toxicity including an increase in the incidence of decreased locomotor activity and loss of fur, and an increase in the weights of adrenal glands and liver was observed. On the contrary, no significant adverse effect on the embryo-fetal development was detected. There were no adverse effects on either pregnant dams or embryo-fetal development at <1,000 mg/kg. These results show that a 14-day repeated oral dose of tert-butyl acetate in rats caused a minimal maternal toxicity including increases in the incidence of clinical signs and the weights of adrenal glands and liver, but no embryotoxicity and teratogenicity at 1,500 mg/kg/day. Under these experimental conditions, the no-observed-adverse-effect level (NOAEL) of tert-butyl acetate is estimated to be 1,000 mg/kg per day for dams and 1,500 mg/kg per day for embryo-fetal development.

• Journal of Conservation Science
• /
• v.33 no.6
• /
• pp.467-483
• /
• 2017

In this study, the degradation properties by temperature stress of $Araldite^{(R)}$ rapid-curing epoxy resin used for inorganic cultural heritages, was identified. The tensile and tensile shear strength of durability decreased for 12,624 hours at temperatures of $40{\sim}60^{\circ}C$. In terms of stability of external stress and temperature, the slow-curing epoxy was superior to the rapid-curing epoxy, and cultural heritage conservation plans should therefore consider the strength and stress properties of restoration materials. Color differences increased for 12,624 hours at temperatures of $40{\sim}60^{\circ}C$, and glossiness decreased. Both color and gloss stability were weak, which necessitates the improvement of optical properties. Thermal properties (weight loss, decomposition temperature, and glass transition temperature) of adhesives are linked to mechanical properties. Interfacial properties of the adherend and water vapor transmission rates of adhesives are linked to performance variation. For porous media (ceramics, brick, and stone), isothermal and isohumid environments are important. For outdoor artifacts on display in museums, changes in physical properties by exposure to varying environmental conditions need to be minimized. These results can be used as baseline data in the study of the degradation velocity and lifetime prediction of rapid-curing epoxy resin for the restoration of cultural heritages.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.3 no.2
• /
• pp.125-133
• /
• 2005

Methodologies of NEWTRIT model, NRC model and AIRDOS-EPA model, which are off-site dose assessment models for regulatory compliance from routine releases of tritium into the environment, were investigated. Using the domestic data, if available, the predictive results of the models were compared. Among them, recently developed NEWTRIT model considers only doses from organically bounded tritium (OBT) due to environmental releases of tritiated water (HTO) . A total dose from all exposure pathways predicted from AIRDOS-EPA model was 1.03 and 2.46 times higher than that from NEWTRIT model and NRC model, respectively. From above result, readers should not have an understanding that a predictive dose from NRC model may be underestimated compared with a realistic dose. It is because of that both mathematical models and corresponding parameter values for regulatory compliance are based on the conservative assumptions. For a dose by food consumption predicted from NEWTRIT model, the contribution of OBT was nearly equivalent to that of HTO due to relatively high consumption of grains in Korean. Although a total dose predicted from NEWTRIT model is similar to that from AIRDOS-EPA model, NEIIfTRIT model may be have a meaning in the understanding of phenomena for the behavior of HTO released into the environment.

• Science of Emotion and Sensibility
• /
• v.14 no.3
• /
• pp.425-434
• /
• 2011

In the present study was to examine the influence of cold stress conditions on memory function in relation with 5-hydroxytryptamine(serotonin, 5-HT), trptophanhydroxylase(TPH) expression and cell proliferation in the hippocampus. For this study, male Sprague-Dawley rats weighing $250{\pm}10g$ (7 weeks in age) were used. The rats were randomly divided into three groups(n = 10 in each group): the $22^{\circ}C$-control group, the $4^{\circ}C$-3 days group, the $4^{\circ}C$-5 weeks group. The environmental temperature at $22^{\circ}C$ set as the normal conditions, $4^{\circ}C$ was as the cold stress conditions. The present results showed that cold stress conditions shorten latency, representing cold stress disturbed memory function. 5-HT and TPH expressions in the dorsal raphe were increased cold stress. Neurogenesis in the dentate gyrus was increased under cold conditions. The present study revealed that cold stress exerted deteriorative memory function. However, through increasing of 5-HT, TPH and BrdU expression under cold stress conditions did not show memory enhancing effect.

• Journal of Microbiology and Biotechnology
• /
• v.12 no.3
• /
• pp.457-462
• /
• 2002

Low Electromagnetic Field (EMF) intensity in the range of $1{\mu}T\;to\;10{\mu}T$(Tesla) was found to enhance the growth of CHO cells and the production of tPA in batch and perfusion cultivations. At $1{\mu}T\;intensity,\;1.3{\times}10^7$ viable cells/ml of maximum cell density and 80 mg/l of maximum tPA production were obtained in batch cultivation, compared to $2.8{\times}10^6$ viable cells/ml and 59 mg tPA/1 in unexposed case (control). A similar trend was observed in the perfusion process, where it was possible to obtain $1.2{\times}10^7$ viable cells/ml of maximum cell density and 81 mg tPA/l of maximum tPA production by more than 80 days of cultivation. However, there was not much difference between $1{\mu}T\;and\;10{\mu}T$ in perfusion cultivation, possibly due to better environmental growth conditions being maintained by continuous feeding of fresh medium into the reactor. On the contrary, both cell growth and tPA production were severely inhibited at higher than 1 mT intensity, showing no growth at 10 mT exposure. Specific growth rate was linearly correlated to specific tPA production rate at $1{\mu}T$EMF intensity, which represents a partially growth-related relationship. It was also found that a large amount of $Ca^2+$ was released at low EMF intensity, even though the cell growth was not much affected. Low EMF intensity significantly improved both cell growth and tPA production, and tPA production seemed to be more affected than the cell growth, possibly due to the changes of cell membrane characteristics. It can be concluded that the elaboration of EMF intensity less than $10{\mu}T$ could improve cell growth and tPA production, but mainly tPA secretion through batch or perfusion process in a bioreactor.

• Environmental and Resource Economics Review
• /
• v.17 no.3
• /
• pp.135-166
• /
• 2008

This paper reports the empirical results of comparing the willingness to pay(WTP) for health risk reductions and the willingness to accept(WTA) for risk increases using experimental market methods in the first time in Korea. Health risks were defined as probabilities of premature death from exposure to one of As, Pb, and THM in tap water. A total of six experimental markets with 15 participants in each experiments were held using 20 repetitive Vickrey second-price sealed-bid auctions. To compare the effects of market experiences, trading a marketed good, candy bar, was introduced before the trading the non-marketed good, drinking water risks. Moreover, an objective risk information was provided after the first 10 trials to incorporate learning processes. Regardless of marketed or non-marketed goods, the mean of WTA exceeded the mean of WTP at the first auction trial. As experimental trials proceeded, the disparity between WTA and WTP for marketed goods disappeared. However results for non-marketed goods were rather mixed to the extent that WTA for health risks from As (relatively high risk leves) were significantly larger than WTP, while there were no significant difference between WTA and WTP for health risks fro Pb and THM (relatively low risk levels). On the other hand, participants seemed to respond in a 'rational' manner to the objective risk information provided, with positive learning effects of market-like experience(especially in the WTA experiments).

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.3 no.3
• /
• pp.183-192
• /
• 2005

Natural ventilation in radioactive waste repositories is considered to be less efficient than mechanically forced ventilation for the repository working environment and hygiene & safety of the public at large, for example, controlling the exposure of airborne radioactive particulate matter. It is, however, considered to play an important role and may be fairly efficient for maintaining environmental conditions of the repository over the duration of its lifetime, for example, moisture content and radon (Rn) gas elimination in repository. This paper describes the feasibility of using natural ventilation which can be generated in the repository itself, depending on the conditions of the natural environment during the periods of repository construction and operation. Evidences from natural cave analogues, actual measurements of natural ventilation pressures in mountain traffic tunnels with vertical shafts, and calculations of airflow rates with given natural ventilation pressures indicate possible benefits from passive ventilation for the prospective Korean radioactive waste repository. Natural ventilation may provide engineers with a cost-efficient method for heat and moisture transfer, and radon (Rn) gas elimination in a radioactive waste repository. The overall thermal performance of the repository may be improved. The dry-out period may be extended, and the seepage flux likely would be decreased.