• 한국재료학회지
• /
• 제31권8호
• /
• pp.450-457
• /
• 2021

From measured thermal conductivity and modeling by simulation, this study suggests that U-factors are highly related to materials used between steel and polymer. The objective and prospective point of this study are to relate the relationship between the U-factor and the thermal conductivity of the materials used. For the characterization, EDX, SEM, a thermal conductive meter, and computer simulation utility are used to analyze the elemental, surface structural properties, and U-factor with a simulation of the used material between steel and polymer. This study set out to divide the curtain wall system that makes up the envelope into an aluminum frame section and entrance frame section and interpret their thermal performance with U-factors. Based on the U-factor thermal analysis results, the target curtain wall system is divided into fix and vent types. The glass is 24 mm double glazing (6 mm common glass +12 mm Argon +6 mm Low E). The same U-factor of 1.45 W/m²·K is applied. The interpretation results show that the U-factor and total U-value of the aluminum frame section are 1.449 and 2.343 W/m²·K, respectively. Meanwhile, those of the entrance frame section are 1.449 and 2.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권6호
• /
• pp.862-870
• /
• 1998

In this paper an experimental investigation of characteristics of developing transitional unsteady flows in a square-sectional 180。 curved duct are presented. The experimental study using air is carried out to measure axial velocity profiles secondary flow velocity profiles and entrance length by using Laser Do ppler Velocimeter(LDV) system. The flow development is found to depend upon Dean number dimensionless angular frequency velocity amplitude ration and cur-vature ratio. Of special interest is the secondary flow generated by centrifugal effects in the plane of the cross-section of the duct. The secondary flows are strong and complicate at entrance region. The entrance length of transitional pulsating flow is obtained to 120。 of bended angle of duct in this experimental conditions.

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권1호
• /
• pp.33-39
• /
• 1999

In this paper an experimenatal investigation of characteristics of developing ransitional steady flows in a square-sectional $180^{\circ}$ curved duct is presented, The experimental study is carried out to measure axial velocity profiles secondary flow velocity profiles and entrance length by using Laser Dopper Velocimeter(LDV) system. The flow development is found to depend upon Dean number and curvature ratio. Of special interest is the secondary flow generated by centrifugal effects in the plane of the cross-section of the duct. The secondary flows becomes strong from $120^{\circ}$ of bended angle on the duct. The entrance length of transitional steady flow is obtained to $120^{\circ}$ of bended angle of the duct in this experimental conditions.

• 한국산학기술학회논문지
• /
• 제14권6호
• /
• pp.2660-2666
• /
• 2013

한국에서는 교육을 중요시하고 있으며, 그 중에 영어교육에 상당히 치중해 있다. 이러한 교육에는 공교육과 사교육이 있는데, 대다수의 가구에서는 사교육에 대한 비용을 지출하고 있다. 따라서 본 연구에서는 각 가구에서 지출하고 있는 사교육비와 수능성적과의 관계를 살펴본다. 분석결과 사교육비의 지출과 수능성적 간에는 양(+)의 관계가 있는 것으로 나타났다. 또한 사교육 총 투입시간과 수능성적 간의 관계에서도 양(+)의 관계가 있는 것으로 나타났다.

• 대한교통학회지
• /
• 제27권1호
• /
• pp.17-25
• /
• 2009

본 연구에서는 중부고속도로 대전${\sim}$통영구간의 장대터널인 육십령터널(L=3.1km)을 대상으로 터널진입부에서부터 터널구간주행을 포함한 터널 진출부까지의 운전자의 시각적 각성수준(Workload)변화를 뇌의 후두엽부분의 생체신호 중 베타파를 이용하여 분석하였다. 실험에 참여한 피실험자는 총 10명으로 다음과 같은 결론을 도출하였다. 첫째, 운전자의 시각적 각성수준은 터널 진입전 200m지점과 비교시 터널입구에서는 약 41% 증가하는 것으로 나타났다. 둘째, 장대터널내에서 주행중인 운전자의 시각 각성값은 터널진입전 200m 지점과 비교시 34.5%증가하였다. 셋째, 장대터널구간을 200m 단위구간으로 나누어 분석한 결과 터널진입후 1.0km구간과 2.4km구간에서 타 구간과 통계적으로 유의한 차이를 보였다. 장대터널내에서 운전자는 안전한 운전을 위해 평균적인 시각 각성수준을 유지한다고 가정할 때, 시각 각성수준이 터널주행시의 평균수준 이하로 내려간다는 것은 적절한 주행상황이라고 볼 수 없다. 따라서 이 구간은 터널을 주행 중인 운전자가 교통사고를 유발할 수 있는 개연성이 존재하는 지점으로 볼 수 있다.

• 한국해양학회지
• /
• 제10권2호
• /
• pp.67-75
• /
• 1975

Tidal Flushing at the entrance channels of tidal bay or estuary in the central western coast of Korea; Gum River Estuary, Garorim Bay, Asan Bay, and Yeomha Estuary were studied with the recent data of current surveys measured by curret meter at three or five anchored stations along the section for one or two tidal periods at mean spring tide. Equilibrium relationship between tidal prism at mean spring tide and minimum flow area below the mean sea level of the channel in alluvial material was found as of O'Brien's (1931, 1969) study. Bed load transport in the tidal channel is balanced with the tidal flushing ability having a mean velocity of about 0.75m/sec or maximum velocity of about 1.25m/sec for a half tidal cycle over the section at mean spring tide which fairly agree with Brunn's study(1955, 1957). flushing actions for different hydraulic depth( mean depth) and bed material size in the channel were reviewed and found that it depend to a minor extent on the factors.

• 소성∙가공
• /
• 제8권2호
• /
• pp.143-151
• /
• 1999

The twisting and extrusion process of the product with trapezoidal helical fin from the round billet is developed by the upper bound analysis. The twisting of extruded product is caused by the twisted die surface connecting the die entrance section and the die exit section linearly. In the analysis, the rotational velocity in angular direction is assumed by the multiplication of radial distance and angular velocity. The angular velocity is increased linearly by axial distance from the die entrance. The increase rate of angular velocity is determined by the minimization of plastic work. The results of the analysis show that the angular velocity of the extruded product increases with the die twisting angle, the reduction of area, and decreases with the die length, the friction condition.

• 대한기계학회논문집B
• /
• 제33권4호
• /
• pp.215-224
• /
• 2009

Analysis for various driven nozzle position changes. The analysis was done for different Reynolds number in entrance region of jet-pump and for several diameter ratios of driven nozzle. (1) The largest absorption energy was found at the point s=1 in condition of diameter ratio 1:3.21 and point s=0.5 in condition of diameter ratio 1:2.25. (2) The absorption energy was not related to the change of entrance velocity and the driven nozzle position having the largest absorption energy was function for cross section ratio. (3) As the position of driven nozzle moves to the downstream, the absorption energy gets weaker. Because the energy from swirl was lost at the cross section gets smaller. (4) As the position of driven nozzle moves to the downstream, the injection energy leans to the upper direction wall and as the Reynolds number increase, the lean phenomenon is more distinct. (5) The flow quantity of driven nozzle, the diameter ratio 1:3.21, was 32% higher than that of 1 : 2.25 and as the inlet velocity gets faster the efficiency decreased. And as the cross section of the driven nozzle increases.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.767-772
• /
• 2004

A dynamic simulation program of a catenary-pantograph system including tunnel section and transient section is developed in this study. The simulation program can accommodate for the pantograph of two panheads and three d.o.f model. Using the developed program, the dynamic characteristics with a SCHUNK'S WBL 85-PANTOGRAPH is analyzed at the conventional TAEBAEK line and its tunnel section when the catenary system is supported by a tunnel bracket. The simulation results show that the variation of contact force and uplift displacement is allowable in general section and the entrance and exit of a tunnel, but the uplift displacement and the separation ratio within tunnel section is difficult to allow.

• 한국철도학회논문집
• /
• 제8권1호
• /
• pp.51-56
• /
• 2005

A dynamic simulation program of a catenary-pantograph system including tunnel section and transient section is developed in this study. The simulation program can accommodate for the pantograph of two panheads and three d.o.f model. Using the developed program, the dynamic characteristics with a SCHUNK'S WBL 85-PANTOGRAPH are analyzed at the conventional TAEBAEK line and its tunnel section when the catenary system is supported by a tunnel bracket. The simulation results show that the variation of contact force md uplift displacement is allowable in general section and the entrance and exit of a tunnel, but the uplift displacement and the separation ratio within tunnel section is difficult to allow.