• International Journal of Automotive Technology
• /
• 제5권4호
• /
• pp.311-319
• /
• 2004

There are many methods to test engine emissions depending on the regulations used such as FTP-75(CYS-75) mode, 10-15 mode and ECE-15 mode. Most of these modes consist of transient conditions such as cranking, rapid acceleration or deceleration modes. In this experimental research, the transient characteristics including cranking and accelerating mode in SI engines were studied to compare pure gasoline with methanol-reformulated fuels for performance and exhaust emissions. The results show that methanol-reformulated fuels have a better emissions reduction rate than that of pure gasoline especially for HC, CO and NOx emissions during cranking mode. The acceleration performances conform to the results of the distillation curve and the CO concentration for RM50 varies slightly in acceleration mode.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.927-929
• /
• 2001

Induction Motor fed by PWM inverter generates the sound and the vibration because of harmonic current and magnetic force characteristics. This paper is investigated the harmonic frequency and noise characteristics of the current and the torque of the induction motor when the input voltage is excited as the sine wave or PWM wave. The performance characteristics of induction motor is analyzed by the F.E.M and the theoretical method.

• 한국정밀공학회지
• /
• 제19권10호
• /
• pp.130-138
• /
• 2002

This paper presents the modeling and analysis of dynamic characteristics of hydraulic snubber in electric power plant. The nonlinear state-space model of 14th order to describe the dynamics of the snubber was established by Simulink. The simulation results show that the hydraulic snubber reacts as like the conventional shock absorbers against the high pulse shock load. The snubber also shows the peculiar characteristics to the small step load, which temporarily lock the control valves up, however maintain same steady-state pressures of all internal chambers in the long run. Two case studies for the analysis of the snubber were addressed. Practical pulse testing method was also proposed to identify the frequency response characteristics of the snubber.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 추계학술대회 논문집 학회본부
• /
• pp.364-366
• /
• 1995

We investigated the Electromigration characteristics in Cu alloyed Al line and the effect of Ti/TiN barrier layer on the characteristics. Test structures were fabricated by wafer level and 50% failure times were tested in the condition of j= 2 MA/$cm^3$, T= 300$^{\circ}C$. The reliability of Al line was improved which was 0.5%Cu Alloyed, but Ti/TiN under layer deteriorated the reliability while TiN over layer improved the characteristics.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.862-863
• /
• 2008

This paper presents the improvement of dynamic characteristics in Interior Permanent Magnet (IPM) type BLDC motor with notch. The notch is applied on the surface of the rotor to reduce the cogging torque and to improve dynamic characteristics. The current, inductance and torque of initial model and optimal model are analyzed by FEA. The validity of improved dynamic characteristics is confirmed.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2002년도 International Meeting on Information Display
• /
• pp.232-235
• /
• 2002

An alternate application of MgO film for the improvement of discharge characteristics and life time in an ac plasma display panel (PDP) is suggested. In this research, we deposited MgO on the phosphor to get the same address characteristics irrespective of each phosphor. To avoid the luminance and efficiency degradation by MgO deposition on the phosphor, we optimized the MgO thickness through experiments. The results showed that PDP with MgO coated phosphor has a uniform formative delay in address discharge and improved degradation characteristics.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 C
• /
• pp.1090-1092
• /
• 1999

In this paper, multi discharge type ozonizer has been designed and manufactured. The of ozonizer is equipped with three electrodes(central electrode of screw shape, internal electrode and external electrode). This paper describes the following two characteristics: (1) The characteristics of discharge with variation of output voltage of AC H.V source, flow rate of oxygen supplied gas and discharge voltage. (2) The characteristics of ozone generation by varying flow rate and discharge power.

• 한국표면공학회지
• /
• 제47권1호
• /
• pp.25-32
• /
• 2014

The effects of shot peening pressure on electrochemical and surface morphological characteristics of ALBC3 alloy were investigated in this work. The surface hardness of ALBC3 alloy was improved by shot peening process under all shot peening pressures between 2 and 5 bar, and the hight value of surface hardness was observed to be about 420 Hv at 4 bar of the shot peening pressure. The shot peened surface presented very rough surface due to shot ball collision. The result of anodic potentiodynamic polarization in seawater revealed that there is no significant difference between the shot peened and non-shot peened specimen in terms of corrosion characteristics. Therefore, the optimum projection pressure is determined to be 4 bar.

• 한국표면공학회지
• /
• 제42권1호
• /
• pp.34-40
• /
• 2009

In the study, it was carried out dissimilar metal welding on materials for Al ship. The electrochemical and mechanical characteristics evaluated for specimen welded by ROBOT. The hardness of welding zone is lower than those of heat affected zone and base metal. At the result of tensile test, the specimen welded with ER5183 welding material presented excellent property compared with ER5556. The polarization trend for the base metal and welding metal showed the effects of concentration polarization due to oxygen reduction and activation polarization due to hydrogen generation. At the Tafel experiments result, the corrosion density in welded with ER5183 welding material presented the lowest value.

• KSTLE International Journal
• /
• 제9권1_2호
• /
• pp.17-21
• /
• 2008

The rolling piston type rotary compressor has been widely used for refrigeration and air-conditioning systems due to its compactness and high-speed operation. The present study is one of studies to maximize the advantages of refrigerant compressors. In addition, because friction characteristics of the critical sliding component is essential in the design of refrigerant compressors, the present study also analyzed the lubrication characteristics of a rotary compressor used for refrigeration and air-conditioning systems. In order to measure the friction force between the vane and the rolling piston, an experimental apparatus known as the Pin-on-Disk was used. Load is applied by the hydraulic servo valve controlling the pressure of the hydraulic cylinder. The results showed that the rotational speed of the shaft, the operating temperature, and the discharge pressure significantly influenced the friction force between the vane and the rolling piston.