• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.5
• /
• pp.693-699
• /
• 1999

In this paper author develops digital governor for medium speed diesel engine. The system is composed of MPU main control module RPM measuring module PWM driving module driver module for F.O. rack drive motor key pad and display module. Experiment results of speed control on 6cyl 1800pm 250kw Daewoo MAN diesel erigine were satisfied for design speci-fications and system could be developed for commercial usage after taking more experiments and endurance tests under various environments.

• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.5
• /
• pp.66-76
• /
• 1987

The control technique for an electronic engine is studied. For this study an IBM-PC and a throttle body fuel injection system are selected. The computer controls fuel injection, spark timing, exhaust gas recirculation and idle speed. Fuel injection is adjusted either by a feed back signal of a zirconia $O_{2}$ sensor or programmed logic for starting, deceleration, warm ing up and idle modes. When a 3-way catalytic converter is used with the electronic engine control system, CO, THC, and NOx were reduced more than 90% simultaneously.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.5
• /
• pp.35-43
• /
• 2014

The automobile industry requires technological innovations to reduce fuel consumption with the public interest in environmental conservation in recent years. Thus, the hybrid system is applied not only to passenger cars but also commercial vehicles. The purpose of this paper is to develop engine ECU_ILS to develop commercial hybrid vehicles. In order to develop the engine and vehicle, the dynamometer and exhaust gas analyzer is needed. However, a lot of time and cost are required. In contrast, the model-based development environment that can be applied to a variety of test conditions can reduce development time. Therefore, a HILS system environment that can consider the behavior of actual vehicles for evaluation of the control logic, fuel consumption and exhaust gas is required. This engine ECU_ILS system was developed in this study, can analyze parameter such as the fuel injection rate, fuel injection time, fuel consumption and exhaust gas like the actual vehicle test using map data. Also, this system is expected to be able to analyze the characteristic of vehicle behavior and the development of peripheral device in relation to engine and vehicles. This HILS system can be used to develop control strategies of commercial hybrid vehicle systems in the future.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.1
• /
• pp.28-35
• /
• 2005

Fuel injection rate of an injector is affected by various injection conditions such as injection duration, fuel temperature, injection pressure, and voltage in LPG liquid injection systems for either a port-fuel-injection(PFI) or a direct injection(DI) in a cylinder. Even fuel injection conditions are changed, the air-fuel ratio should be accurately controlled to educe exhaust emissions. In this study, correction factor for the fuel injection rate of an injector is derived from the density ratio and the pressure difference ratio. A voltage correction factor is researched from injection test results on an LPG liquid injection engine. A compensation method of the fuel injection rate is proposed for a fuel injection control system. The experimental results for the LPG liquid injection system in a SI-engine show that this system works well on experimental range of engine speed and load conditions. And the fuel injection rate is accurately controlled by the proposed compensation method.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.533-536
• /
• 2009

The power control system of Smart UAV is similar to the propeller pitch governing concept of turboprop aircraft. The pilot inputs the engine power directly and the pitch governor controls the rotational speed of proprotor. In this paper, the engine status data from ground test of Smart UAV, such as the relationship of PLA vs. Gas generator speed and power are compared with the result of engine performance calculation program.

• Journal of Biosystems Engineering
• /
• v.19 no.4
• /
• pp.291-300
• /
• 1994

It is desired to operate tractor engines at or near maximum torque much of the time in field operation to increase fuel efficiency. To do this it is necessary to reduce engine speed and to shift gears to higher ratios as frequently as possible. Because of load variations in most drawbar work and inconvenience in gear shift, however, gear-type transmission are usually set in one ratio at unnecessarily high engine speeds, and engine-torque variations are used to compensate for changes in drawbar load. As a result, the most of time the tractor is not operated efficiently in terms of fuel consumption and work output. The objective of this study was to develop an automatic control system which is able to operate a tractor equipped with gear transmission under the optimal condition in terms of fuel efficiency with automatic governor setting and gear shift. An indoor experimental test set which can be used to simulate tractor operation, control engine speed and transmission ratio was developed in the previous paper. In this paper, the performance of the optimal operation system is reported. Through a series of tests, it was found that the automatic control system for optimal operation of tractors with gear transmission had a satisfactory performance.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.49 no.2
• /
• pp.1-9
• /
• 2012

In this paper, we design and implement a DCS (Distributed Control System) based on dual field-bus for ship engine. For monitoring and controlling the condition of the ship engine, an implemented DCS is consisted of two-tier communication structure by using CAN (Controller Area Network) and MODBUS protocols. The first-tier is consisted of CAN protocol for sharing the condition of the ship engine by each implemented monitoring system. By using MODBUS protocol, the second-tier is used for communicating the monitoring data from an implemented DCS to AMS(Alarm Monitoring System). We verified and tested our scheme and implemented DCS by KR (Korea Register) technical rules through experimental tests.

• Journal of Power System Engineering
• /
• v.2 no.3
• /
• pp.68-73
• /
• 1998

The propulsion diesel engine have been widely applied with a mechanical governor to control the truck speed for a long time. But it was recently very difficult for mechanical governor to control the speed of long stock and diesel engine of truck because of hunting by dead time between fuel injection and power output. This study is aimed to configure the modeling for performance simulation regarding to diesel truck operation which could be suppressed for hunting. The modeling have been made on the base of dynamic characteristic such as electronic governor, injection of fuel system and operating states of diesel engine truck. Real model system have been introduced for deciding reacting parameters and for the comparison of resulting performance in simulation. In results of simulation, we obtained items which diesel truck drives for suppressed hunting.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.3
• /
• pp.446-454
• /
• 2008

Control devices for fire safety systems located in a engine room are to be arranged at a safe position which is easily accessible during a fire. To develop an interpretation for the safe position in engine rooms, calculation and experiments are carried out to determine a correlation between radiant heat and distance from fire in this paper. On the basis of results of this research, the control devices for a main engine are to be installed in the behind side of an obstruction to reduce radiant heat from the fire of the main engine. In case of other control devices, they are also to be provided in the same manner of control devices for the main engine or are to be placed with 5 meters far from fire hazards.

• Journal of the Korea Convergence Society
• /
• v.4 no.3
• /
• pp.43-50
• /
• 2013

This paper presents a model predictive control (MPC) based on a neural network (NN) model for air/fuel ration (AFR) control of automotive engines. The novelty of the paper is that the severe nonlinearity of the engine dynamics are modelled by a NN to a high precision, and adaptation of the NN model can cope with system uncertainty and time varying effects. A single dimensional optimization algorithm is used in the paper to speed up the optimization so that it can be implemented to the engine fast dynamics. Simulations on a widely used mean value engine model (MVEM) demonstrate effectiveness of the developed method.