• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.319-324
• /
• 2001

A finite element model for the process of squeeze casting for metal matrix composites (MMCs) in cylindrical mold is developed. The fluid flow and the heat transfer are the fundamental phenomena in the squeeze casing process. To describe heat transfer with solidification of molten aluminum, the energy equation in terms of temperature and enthalpy are applied to two dimensional axisymmetric model which is similar to the experimental system. And one dimensional flow model is employed to simulate the transient metal flow. The direct iteration technique was used to solve the resulting nonlinear algebraic equations. A computer program is developed to calculate the enthalpy, temperature and fluid velocity. Cooling curves and temperature distribution during infiltration and solidification are calculated for pure aluminum. The temperature is measured and recorded experimentally. At two points of the perform inside and one point of the mold outside, thermocouple wire are installed. The time-temperature data are compared with the calculated cooling curves. The experimental results show that the finite element model can estimate the solidification time and predict the cooling process.

• 대한기계학회논문집B
• /
• 제22권4호
• /
• pp.499-509
• /
• 1998

In the absorption process of water vapor in a liquid film, the composition of the gas phase, in which a non-absorbable gas is combined with the absorbate influences the transport characteristics remarkably. In the present study, the absorption processes of water vapor into aqueous solution of lithium bromide in the presence of non-absorbable gases were investigated analytically. The continuity, momentum, energy and diffusion equations for the solution film and gas phase were formulated in integral forms and solved numerically. It was found that the mass transfer resistance in gas phase increased with the concentration of non-absorbable gas. However the primary resistance to mass transfer was in the liquid phase. As the concentration of non-absorbable gas in the absorbate increased, the liquid-vapor interfacial temperature and concentration of absorbate in solution decreased, which resulted in the reduction of absorption rate. The reduction of mass transfer rate was found to be significant for the addition of a small amount of non-absorbable gas to the pure vapor, especially at the outlet of an absorber where non-absorbable gases accumulated. At higher non-absorbable gas concentration, the decrease of absorption flux was almost linear to the volumetric concentration of non-absorbable gas.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2005년도 동계학술발표대회 논문집
• /
• pp.341-346
• /
• 2005

Nowadays, adsorption chillers have been receiving considerable attentions as they are energy-saving and environmental1y benign systems. A Fin & tube type heat exchanger in which adsorption/desorption take place is required more compact size. The adsorption chiller is expected to have high energy-efficiency in utilizing the waste heat exhausted from a process. The objectives of this paper are to investigate the effect of fin pitch of fin & tube on the adsorption performance and to develop an optimal design fin & tube heat exchanger in the silica gel/water adsorption chiller. Previous study concluded that optimal particle size selected 0.5mm, type HO silica gel, and fundamental heat transfer & mass transfer experiments carried out. From the numerical results, the adsorption rate for the fin pitch 2.5mm is the highest than that for the fin pitch 5mm, 7.5mm and 10mm. Also cooling water & hot water temperature affect the adsorption rate.

• 설비공학논문집
• /
• 제6권4호
• /
• pp.453-462
• /
• 1994

An unsteady quasi one-dimensional model of momentum, heat and mass transfer in a falling film of a vertical plate absorber which is cooled by air was developed using the integral method. Energy conservation of the absorber wall is considered in the model. The model can predict absorption rate, film thickness and mean velocity as well as concentration and temperature profiles. Predictions of steady state temperature and concentration profiles for LiBr/water system for constant wall temperature condition are in good agreement with the two-dimensional finite difference method solutions. Effects of operating conditions, such as convective heat transfer coefficient between the cooling air and the absorber wall, cooling air temperature and film thickness at inlet, on absorption rate of water vapor into LiBr/water solution were shown.

• Bulletin of the Korean Chemical Society
• /
• 제31권12호
• /
• pp.3693-3696
• /
• 2010

We experimentally measure the kinetic energy and angular distributions of photoelectrons of $N_2$ as a function of 410 nm femtosecond laser intensity by using velocity map imaging technique. The strong-field multiphoton ionization of molecules shares many of the characteristics with those of atoms. Electron kinetic energies are nearly independent of laser intensities. The independence suggests that the electron peaks in the photoelectron spectrum actually result from a two-step process, indicative of the occurrence of real population in the intermediate states. The relative amplitudes of electron peaks indicate that in the two-step process, nonresonant population transfer dominates for low intensities, while resonant population transfer dominates for higher intensities.

• 대한기계학회논문집B
• /
• 제41권6호
• /
• pp.415-421
• /
• 2017

환경규제의 강화에 따라 수처리 비용이 증가하는 추세이므로 폭기공정의 에너지 이용효율을 제고할 수 있는 소요동력에 대한 보다 정량적인 연구가 필요하다. 본 논문은 폭기공정의 물질전달 특성을 규명하기 위해 물질전달 계수와 기체 포집율 및 소요동력에 대한 상관관계식을 제시하였다. 소요동력이 커지면 기체 포집율은 감소하고 레이놀드 수는 증가하며, 혼합유동 선단 도달거리와 확산도가 증대되므로 물질전달 계수는 증가하였다. 물질전달 계수와 기체 포집율 및 소요동력의 상관관계 규명을 위해 제시한 실험식은 최대 약 ${\pm}10%$의 오차 범위에서 실험결과와 일치하였다.

• 한국산학기술학회논문지
• /
• 제15권3호
• /
• pp.1795-1800
• /
• 2014

본 논문은 생물학적 활성오니 폐수처리공정의 열전달 모델식을 제시하여 공정의 온도를 예측하였다. 열전달 모델은 폐수처리공정에 들어오고 나가는 모든 열을 고려하였다. 공정에 들어오는 열은 태양 복사열과 포기조 impeller의 기계적 에너지의 변환열, 포기조 내의 생화학 반응열이다. 공정에서 나가는 열은 폐수 자체의 복사열, 포기작용에 의한 증발열과 포기조 표면으로 나가는 전도열, 바람에 의한 대류열, 포기조와 지표면과의 전도열을 고려하였다. 들어오고 나가는 모든 열은 기존의 열전달 경험식을 적용하였다. 적용된 경험식으로 폐수처리장 공정의 열전달 모델식을 제시하였다. 모델식으로 실제 폐수처리공정의 온도를 예측하였으며, 모델식 예측치와 실제값이 $1.0^{\circ}C$ 이내로 일치하였다.

• Journal of the Optical Society of Korea
• /
• 제1권1호
• /
• pp.5-9
• /
• 1997

Energy transfer direction in $Er^{3+}-Tm^{3+}$-codoped fluorozirconate glasses has been studied. For $Er^{3+}-Tm^{3+}$-codoped glasses, the dependence of the green emission intensity on the pump power (Pex) of 800 nm has ranged from (Pex)$^2$ to (Pex)$^3$. From this multistep absorption, a 1.48 $\mu m$ emission from the $^3F_4{\rightarrow}^3H_4$ transition on Tm$^{3+}$ ion has been found to transfer into $^4I_{13/2}$, $^4I_{9/2}$ and $^4S_{3/2}$ on $Er^{3+}$ ion. In case of the 1.06 $\mu m$ pumping, the emissin ratio of $^3H_4$ level in $Tm^{3+}$ to $^4I_{13/2}$ in $Er^{3+}$ showed that the amount of the energy transfer from $Tm^{3+}$ into $Er^{3+}$ increased with the increasing concentration of $Tm^{3+}$ ion. Our two kinds of pumping scheme suggest that the direction of dominant energy transfer between $Er^{3+}$ and $Tm^{3+}$ should be dependent on whether the $^3F_4$ level resonates in $Tm^{3+}$ the level or not.

• 설비공학논문집
• /
• 제28권8호
• /
• pp.305-310
• /
• 2016

A thermal storage systems was designed to correspond to the temporal or quantitative variation in the thermal energy demand, and most of its heat is stored using the latent and sensible heat of the heat storage material. The heat storage method using latent heat has a very complex phenomenon for heat transfer and thermal behavior because it is accompanied by a phase change in the course of heating/cooling of the heat storage material. Therefore, many studies have been conducted to produce an experimentally accessible as well as numerical approach to confirm the heat transfer and thermal behavior of phase change materials. The purpose of this study was to investigate the problems encountered during the actual heat transfer from an internal storage tank through simulation of the process of storing and utilizing thermal energy from the thermal storage tank containing charged PCM. This study used analysis methods to investigate the heat transfer characteristics of the PCM with simultaneous heating/cooling conditions in the rectangular space simulating the thermal storage tank. A numerical analysis was carried out in a state considering natural convection using the ANSYS FLUENT(R) program. The result indicates that the slope of the liquid-solid interface in the analysis field changed according to the temperature difference between the heating surface and cooling surface.

• 한국재료학회지
• /
• 제19권4호
• /
• pp.224-227
• /
• 2009

Nanofabrication is an essential process throughout industry. Technologies that produce general nanofabrication, such as e-beam lithography, dip-pen lithography, DUV lithography, immersion lithography, and laser interference lithography, have drawbacks including complicated processes, low throughput, and high costs, whereas nano-transfer printing (nTP) is inexpensive, simple, and can produce patterns on non-plane substrates and multilayer structures. In general nTP, the coherency of gold-deposited stamps is strengthened by using SAM treatment on substrates, so the gold patterns are transferred from stamps to substrates. However, it is hard to apply to transfer other metallic materials, and the existing nTP process requires a complicated surface treatment. Therefore, it is necessary to simplify the nTP technology to obtain an easy and simple method for fabricating metal patterns. In this paper, asnTP process with poly vinyl alcohol (PVA) mold was proposed without any chemical treatment. At first, a PVA mold was duplicated from the master mold. Then, a Mo layer, with a thickness of 20 nm, was deposited on the PVA mold. The Mo deposited PVA mold was put on the Si wafer substrate, and nTP process progressed. After the nTP process, the PVA mold was removed using DI water, and transferred Mo nano patterns were characterized by a Scanning electron micrograph (SEM) and Energy Dispersive spectroscopy (EDS).