• Journal of Magnetics
• /
• 제16권2호
• /
• pp.181-185
• /
• 2011

To improve trapped field characteristics of a high temperature superconducting (HTS) bulk, a technique to implement artificial holes has been studied. The artificial holes, filled up with epoxy or metal, may provide better cooling channel and enhance mechanical strength of the HTS bulk. Although many useful researches based on experiments have been reported, a numerical approach is still limited because of several reasons that include: 1) highly non-linear electromagnetic properties of HTS; and 2) difficulty in modeling of randomly scattered "small" artificial holes. In this paper, a 2-D finite element method with iteration is adopted to analyze trapped field characteristics of HTS bulk with artificial holes. The validity of the calculation is verified by comparison between measurement and calculation of a trapped field in a $40{\times}40\;mm$ square and 3.1 mm thick HTS bulk having 16 artificial holes with diameter of 0.7 mm. The effects of sizes and array patterns of artificial holes on distribution of trapped field within HTS bulk are numerically investigated using suggested method.

• Journal of Electrical Engineering and Technology
• /
• 제13권6호
• /
• pp.2402-2411
• /
• 2018

Fluoronitriles-$CO_2$ gas mixtures are promising alternatives to $SF_6$ in environmentally-friendly gas-insulated transmission lines (GILs). Insulating gas heat transfer characteristics are of major significance for the current-carrying capacity design and operational state monitoring of GILs. In this paper, a three-dimensional calculation model was established for a GIL using the thermal-fluid coupled finite element method. The calculated results showed close agreement with experimentally measured data. The temperature distribution of a GIL filled with the Fluoronitriles-$CO_2$ mixture was obtained and compared with those of GILs filled with $CO_2$ and $SF_6$. Furthermore, the effects of the mixture ratio of the component gases and the gas pressure on the temperature rise and current-carrying capacity of the GIL were analyzed. Results indicated that the heat transfer performance of the Fluoronitriles-$CO_2$ gas mixture was better than that of $CO_2$ but worse than that of $SF_6$. When compared with $SF_6$, use of the Fluoronitriles-$CO_2$ gas mixture caused a reduction in the GIL's current-carrying capacity. In addition, increasing the Fluoronitriles gas component ratio or increasing the pressure of the insulating gas mixture could improve the heat dissipation and current-carrying capacity of the GIL. These research results can be used to design environmentally-friendly GILs containing Fluoronitriles-$CO_2$ gas mixtures.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.956-961
• /
• 2000

This paper describes the design of a small size Alkali Metal Thermal to Electric Converter (AMTEC) which employs a capillary structure for recirculating sodium working fluid. The cycle is based on the simple and small capillary type ${\beta}"$ -alumina and wick tube element. The proposed cell consists of the 37 conversion elements with capillary tube of $50{\mu}m$ in diameter and the sealed cylindrical vessel of 22mm in outer diameter. Results on the cycle analysis of sodium flow and heat transfer in the cell showed that the expected power output was 4.65W and the conversion efficiency was 19% for the source temperature of 900K.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권5호
• /
• pp.847-852
• /
• 2004

The wind turbine blade is the equipment converted wind into electric energy. The effect of the blade has influence of the output power and efficiency of wind turbine. The design of blade is considered of lift-to-drag ratio. structure. a condition of process of manufacture and stable maximum lift coefficient, etc. This study is used the simplified method for design of the aerodynamic blade and aerodynamic analysis used blade element method This Process is programed by delphi-language. The Program has any input values such as tip speed ratio blade length. hub length. a section of shape and max lift-to-drag ratio. The Program displays chord length and twist angle by input value and analyzes performance of the blade.

• 센서학회지
• /
• 제26권2호
• /
• pp.107-113
• /
• 2017

Energy source of a piezo-electric harvester is vibration. Sources of vibration are machineries operated with high frequencies, constructions and people operated with low frequencies and etc. In this study, we tried to figure out power generation properties over vibrations upon angles of a piezo-cantilever for applying them to movements of the construction and/or people, which are vibration sources at low frequencies. A uni-morph cantilever with a $59mm{\times}29mm{\times}0.2mm$ piezo-electric element attached on a $71mm{\times}46mm{\times}0.25mm$ copperplate was used. A spring was attached to the lower side of the cantilever and a mass was attached on the opposite side. Also, a structure with a specific angle which is an angle in between the ground and the cantilever was prepared and then, connected to a spring or the cantilever. Then, this structure was divided into the A-type and B-type and excited in the direction of z- axis. After that, the angle between the ground and the cantilever was changed and excited by 1 to 10 Hz upon the existence of a spring and/or a mass to compare power generation properties.

• Journal of Power Electronics
• /
• 제13권3호
• /
• pp.362-368
• /
• 2013

Commercial home appliances using remotely controlled systems consume electric power while in standby mode to prepare for receiving a remote turn-on signal. The proposed power system can significantly reduce standby power consumption without increasing cost. Furthermore, since a Electronic Double Layer Capacitor (EDLC) is used as an auxiliary power storage element, the life cycle is longer and system reliability can be better than with existing approaches. When the energy of the EDLC is not sufficient for turning on the appliance, the power system charges the EDLC without affecting the main system. The proposed power system is verified with a commercial LCD TV and a 3.93mW standby consumption is obtained. This standby consumption can be regarded as zero standby equipment according to the IEC-62031 standard.

• 멤브레인
• /
• 제27권6호
• /
• pp.477-486
• /
• 2017

수소는 산업용 전력생산, 자동차용 연료 등을 위한 대체가능한 에너지 담체로 인식되고 있다. 미래 저탄소 에너지 시스템에서 에너지 저장은 전력 수요에 유연하지 않거나 간헐적인 공급의 균형을 이루기 위한 중추적인 역할을 담당할 수 있을 것이다. 수소는 에너지 담체로서 전기에너지를 화학에너지로, 화학에너지를 전기에너지로 변환할 수 있는 에너지 저장 방법 중의 하나이다. 수소제조 방법 중에서, 특히, 물의 전기분해를 이용한 방법은 신재생 에너지원과의 접목을 고려할 때 가장 효율적이고 실용적인 방법으로 여겨지고 있다. 물 전기분해 수소제조 기술은 전기를 이용하여 수소를 물로부터 직접 제조하는 방법으로, 화석연료 이용 제조방법과 비교하여 수소를 제조할 때 지구환경 오염물질인 이산화탄소의 배출이 없다. 수소제조 방법 중의 하나인 물 전기분해의 원리와 물 전기분해의 종류인 알칼리 수전해(AWE, alkaline water electrolysis), 고분자 전해질막 수전해(PEMWE, polymer electrolyte membrane water electrolysis), 고온 수증기 전기분해(HTSE, high temperature steam electrolysis)에 대하여 분석하고자 하였다. 물 전기분해는 수소제조 방법의 하나로 연구가 진행되고 있으며, 최근에는 PTG (power to gas)와 PTL (power to liquid) 시스템의 요소기술로도 주목을 받고 있다. 본 총설에서는 물 전기분해에 대한 원리와 종류, 특히 알칼리 수전해에 대한 최근 연구동향에 대해 설명하였다.

• 전기학회논문지
• /
• 제67권10호
• /
• pp.1382-1387
• /
• 2018

There is a high demand for energy efficiency improvement of factories that make up a large part of national electric energy. Therefore, research on smart FEMS technology for monitoring, analyzing and controlling energy consumption patterns is under way, but there is still a lack of research on detailed element technology for communication and control inside the factory. In this paper, we proposed OFDM VLC system based on MODBUS protocol for communication between gateways, sensors, and devices to implement smart FEMS in indoor factory environment. Assuming a conveyor belt load control, we validated the proposed system by simulating the inverter motor control and checking the performance.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.656-659
• /
• 2000

Recently, the skeleton type 2-phase brushless DC motor has been used in electric home appliance for low price and low energy consumption. In this paper, we analyzed a skeleton type 2-phase BLDC motor using time-step finite element method. And the validity of analysis is confirmed by measuring the flux distribution on the surface of permanent magnet and back-EMF. As well, we have calculated the dynamic characteristics of target motor considering the Hall sensor position. So, we have found the optimum switching position, and improved efficiency of 2-phase BLDC motor.

• Journal of Electrical Engineering and Technology
• /
• 제13권5호
• /
• pp.1917-1926
• /
• 2018

In view of the current state of the reserves of electric energy generated resources and the share of electric motors in electricity consumption, many researches and studies related to efficiency in electric motors are being made. The presented work is related to the Axial Flux Permanent Magnet Synchronous Motor (AF-PMSM), which has recently undergone significant work based on the development of magnet and motor technology. In this study, a novel AF-PMSM was designed analytically through Finite Element Method (FEM) which can be started by connecting to a line such as an asynchronous motor in a transient state and can operate with high efficiency and power factor after synchronization in steady state without the need for an expensive motor drive. According to the obtained FEM results, a design with an efficiency class of IE4 of 5.5 kW shaft power, a 4 poles motor was obtained. As a result, economic calculations indicate that the extra cost of the designed Line start AF-PMSM with respect to the asynchronous motor is rapidly compensated by energy saving due to a more efficient operation, especially constant speed operations. As a result of the analysis obtained, the targeted values are reached. For induction motors and radial flux permanent magnet synchronous motors, a good alternative motor that can operate with high efficiency and power factor has been obtained.