• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.9 no.4
• /
• pp.219-230
• /
• 2011

The nuclear fuel cycle (NFC) analysis is a study to set a NFC policy and to promote systematic researches by analyzing technologies and deriving requirements at each stage of a fuel cycle. System analysis techniques are utilized for comparative analysis and assessment of options on a considered system. In case that NFC is taken into consideration various methods of the system analysis techniques could be applied depending on the range of an interest. This study presented NFC analysis strategies for the development of a domestic advanced NFC and analysis techniques applicable to different phases of the analysis. Strategically, NFC analysis necessitates the linkage with technology analyses, domestic and international interests, and a national energy program. In this respect, a trade-off study is readily applicable since it includes various aspects on NFC as metrics and then analyzes the considered NFC options according to the derived metrics. In this study, the trade-off study was identified as a method for NFC analysis with the derived strategies and it was expected to be used for development of an advanced NFC. A technology readiness level (TRL) method and NFC simulation codes could be utilized to obtain the required metrics and data for assessment in the trade-off study. The methodologies would guide a direction of technology development by comparing and assessing technological, economical, environmental, and other aspects on the alternatives. Consequently, they would contribute for systematic development and deployment of an appropriate advanced NFC.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.49 no.1
• /
• pp.64-73
• /
• 2012

In this paper, a new land preview system using laser range finder based on heave estimation algorithm is proposed. The proposed land preview system is an equipment which measures the shape of forward topography for autonomous vehicle. To implement this land preview system, the laser range finder is generally used because of its wide measuring range and robustness under various environmental condition. Then the current location of the vehicle has to be known to generate the shape of forward topography and sensors based on acceleration such as IMU and accelerometer are generally utilized to measure heave motion in the conventional land preview system. However the drawback to these sensors is that they are too expensive for low-cost vehicle such as mobile robot and their measurement error is increased for mobile robot with abrupt acceleration. In order to overcome this drawback, an algorithm that estimates heave motion using the information of odometer and previously measured topography is proposed in this paper. The proposed land preview system based on the heave estimation algorithm is verified through simulation and experiments for various terrain using a simulator and a real system.

• The Journal of the Acoustical Society of Korea
• /
• v.24 no.2
• /
• pp.103-110
• /
• 2005

Providing adequate amount of spatial impression for spaciousness) has been known to be one of the most important design considerations for the good acoustics of rooms for music. and the measurement, of room acoustics using parameters. such as LEF and IACC, forms an essential part of such evaluation. However. it is unavoidable to use different transducers (figure of eight microphones. head and torso) for the measurement of each parameter and it tends to make the measurement procedure complicated. The Present work tried to provide a simpler way to measure these binaural room acoustic parameters including monaural ones with a single measurement system using both spatial information collected through a 5-channel microphone and a trained neural network. A computer simulation program, CATT-Acoustic V7.2. which allowed us to obtain exactly the same spatial information as a 5-channel microphone was used. since it requires quite a large amount of data for practical training of a neural network. Since each reflection has different energy. delay and direction, energy should be integrated properly. the concept of ray tracing method was applied inversely in this work. Also applying weightings according to the delay times was considered in this work. Finally, predicted results were compared with the measured data md their correlations were analyzed and discussed.

• Journal of Energy Engineering
• /
• v.6 no.1
• /
• pp.104-113
• /
• 1997

This study aims to develop an analysis model using a commercial process simulator-ASPEN PLUS for an IGCC (Integrated Gasification Combined Cycle) system consisting a dry coal feeding, oxygen-blown entrained gasification process by Shell, a low temperature gas clean up process, a General Electric MS7001FA gas turbine, a three pressure, natural recirculation heat recovery steam generator, a regenerative, condensing steam turbine and a cryogenic air separation unit. The comparison between those results of this study and reference one done by other engineer at design conditions shows consistency which means the soundness of this model. The greater moisture contents in Illinois#6 coal causes decreasing gasifier temperature and the greater ash and sulfur content hurt system efficiency due to increased heat loss. As the results of sensitivity analysis using developed model for the parameters of gasifier operating pressure, steam/coal ratio and oxygen/coal ratio, the gasifier temperature increases while combustible gases (CO＋H2) decreases throughout the pressure going up. In the steam/coal ratio analysis, when the feeding steam increases the maximum combustible gas generation point moves to lower oxygen/coal ratio feeding condition. Finally, for the oxygen/coal ratio analysis, it shows oxygen/coal ratio 0.77 as a optimum operating condition at steam/coal feeding ratio 0.2.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.68.1-68.1
• /
• 2010

염료감응형 태양전지에서 가능한 광전자의 이동경로에 대해 살펴보면 빛 에너지를 흡수한 루테늄계 염료는 기저상태에서 여기상태로 전이한 후 광전자의 반도체 전도띠로 전자주입이 이루어진다. 이러한 전자 중 일부는 반도체산화물의 트랩으로의 전이와 트랩에서 염료 기저상태로의 전이가 일어나고 일부 전자는 전해질의 이온종 또는 산화된 염료와 재결합하는 현상이 일어난다. 본 연구에서는 이러한 전자의 재결합을 막고자 p형 반도체인 NiO paste를 제작하여 $TiO_2$ 광전극 층 위에 코팅하였다. 코팅된 NiO 층은 홀수용체로서 염료에 전자를 제공해 주는 역할과 동시에 $TiO_2$ 가전도대로 이동되었던 전자들이 염료의 기저상태의 홀이나 전해질로의 전자 유입이 이루어지는 전자의 재결합을 막는 방벽의 역할을 동시에 하게 된다. 제작된 염료감응형 태양전지 셀의 에너지 변환효율 특성을 알아보기 위하여 1000 W Xe Arc Lamp와 Air Mass 1.5, filter가 장착된 Thermo-Preal (USA) Solar simulator system을 사용하여 개방전압 (Voc), 광전류 (Isc), fill factor (FF), 에너지변환 효율 (${\eta}$)을 조사하였으며 광학현미경을 통해 염료의 흡착 정도를 비교해 보았다. NiO의 코팅 두께나 NiO 나노입자 크기에 따라 염료감응형태양전지에서 에너지변환효율에 미치는 영향을 조사하였다. NiO가 코팅되지 않은 $TiO_2$ 광전극과 비교해 볼 때 NiO 코팅시 Voc와 Isc의 증가로 인해 에너지변환효율이 20% 이상 향상되는 것을 볼 수 있었다.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.14 no.9
• /
• pp.3639-3662
• /
• 2020

The network capability to accomplish its functions in a timely fashion under failures and attacks is known as survivability. Ad hoc routing protocols have been studied and extended to various domains, such as Intelligent Transport Systems (ITSs), Unmanned Aerial Vehicles (UAVs), underwater acoustic networks, and Internet of Things (IoT) focusing on different aspects, such as security, QoS, energy. The existing solutions proposed in this domain incur substantial overhead and eventually become burden on the network, especially when there are fewer attacks or no attack at all. There is a need that the effectiveness of these routing protocols be analyzed in the presence of Denial of Service (DoS) attacks without any intrusion detection or prevention system. This will enable us to establish and identify the inherently stable routing protocols that are capable to survive longer in the presence of these attacks. This work presents a DoS attack case study to perform theoretical analysis of survivability on node and network level in the presence of DoS attacks. We evaluate the performance of reactive and proactive routing protocols and analyse their survivability. For experimentation, we use NS-2 simulator without detection or prevention capabilities. Results show that proactive protocols perform better in terms of throughput, overhead and packet drop.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10b
• /
• pp.1705-1711
• /
• 1991

On-line fault detection and diagnosis has an increasing interest in a chemical process industry, especially for a process control and automation. The chemical process needs an intelligent operation-aided workstation which can do such tasks as process monitoring, fault detection, fault diagnosis and action guidance in semiautomatic mode. These tasks can increase the performance of a process operation and give merits in economics, safety and reliability. Aiming these tasks, series of researches have been done in our lab. Main results from these researches are building appropriate knowledge representation models and a diagnosis mechanism for fault detection and diagnosis in a chemical process. The knowledge representation schemes developed in our previous research, the symptom tree model and the fault-consequence digraph, showed the effectiveness and the usefulness in a real-time application, of the process diagnosis, especially in large and complex plants. However in our previous approach, the diagnosis speed is its demerit in spite of its merits of high resolution, mainly due to using two knowledge models complementarily. In our current study, new knowledge representation scheme is developed which integrates the previous two knowledge models, the symptom tree and the fault-consequence digraph, into one. This new model is constructed using a material balance, energy balance, momentum balance and equipment constraints. Controller related constraints are included in this new model, which possesses merits of the two previous models. This new integrated model will be tested and verified by the real-time application in a BTX process or a crude unit process. The reliability and flexibility will be greatly enhanced compared to the previous model in spite of the low diagnosis speed. Nexpert Object for the expert system shell and SUN4 workstation for the hardware platform are used. TCP/IP for a communication protocol and interfacing to a dynamic simulator, SPEEDUP, for a dynamic data generation are being studied.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.5
• /
• pp.23-36
• /
• 2004

A computationally efficient and accurate Monte Carlo (MC) simulator of electron beam lithography process has been developed for sub-0.l${\mu}{\textrm}{m}$ T-shaped gate formation in the HEMT devices for millimeter-wave frequencies. For the exposure process by electron to we newly and efficiently modeled the inner-shell electron scattering and its discrete energy loss with an incident electron for multi-layer resists and heterogeneous multi-layer targets in the MC simulation. In order to form the T-gate shape in resist layers, we usually use the different developer for each resist layer to obtain good reproducibility in the fabrication of HEMT devices. To model accurately the real fabrication process of electron beam lithography, we have applied the different developers in trilayer resist system By using this model we have simulated and analyzed 0.l${\mu}{\textrm}{m}$ T-gate fabrication process in the HEMT devices, and showed our simulation results with the SEM observations of the T-shaped gate process.

• Atmosphere
• /
• v.29 no.4
• /
• pp.355-365
• /
• 2019

Based on in-situ monitoring data produced by National Institute of Meteorological Sciences, we evaluated the performance of Joint UK Land Environment Simulator (JULES) on the surface energy balance for rice-paddy and cropland in Korea with the operational ancillary data used for Unified Model (UM) Local Data Assimilation and Prediction System (LDAPS) (CTL) and the high-resolution ancillary data from external sources (EXP). For these experiments, we employed the one-year (March 2015~February 2016) observations of eddy-covariance fluxes and soil moisture contents from a double-cropping rice-paddy in BoSeong and a cropland in AnDong. On the rice-paddy site the model performed better in the CTL experiment except for the sensible heat flux, and the latent heat flux was underestimated in both of experiments which can be inferred that the model represents flood-irrigated surface poorly. On the cropland site the model performance of the EXP experiment was worse than that of CTL experiment related to unrealistic surface type fractions. The pattern of the modeled soil moisture was similar to the observation but more variable in time. Our results shed a light on that 1) the improvement of land scheme for the flood-irrigated rice-paddy and 2) the construction of appropriate high-resolution ancillary data should be considered in the future research.

• Fashion & Textile Research Journal
• /
• v.14 no.3
• /
• pp.486-491
• /
• 2012

This study examined the sound characteristics of Taekwondo uniform fabrics to investigate the relationship between the sound parameters and the mechanical properties of the fabric as well as to provide the conditions to maximize the frictional sound of the uniform. Frictional sounds of 6 fabrics for Taekwondo uniforms were generated by the Simulator for Frictional Sound of Fabrics. The frictional speeds were controlled at low(0.62 m/s), at mid(1.21 m/s) and at high(2.25 m/s) speed, respectively. The frictional sounds were recorded using a Data Recorder and Sound Quality System subsequently, the physical sound properties such as SPL(Sound Pressure Level) and Zwicker's psychoacoustic parameters were calculated. Mechanical properties of specimens were measured by KES-FB. The SPL, Loudness(Z) values increased while Sharpness(Z) value decreased. In the physical sound parameter, specimen E had the highest SPL value at low speed and specimen B at high speed. In case of Zwicker's psychoacoustic parameters, the commercially available Taekwondo uniform fabrics(E, F) showed higher values of Loudness(Z), Sharpness(Z), and Roughness(Z), that indicates they can produce louder, shaper and rougher sounds than other fabrics for Taekwondo uniforms. The decisive factors that affected frictional sounds for Taekwondo uniforms were W(weight) as well as EM(elongation at maximum load) at low speed and WC(compressional energy) at high speed.