• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.2
• /
• pp.123-132
• /
• 2014

The maritime sector is advancing with dedicated endeavor to reduce greenhouse gas in addressing issues with regards to global warming. Since 01 January 2013, the International Maritime Organization (IMO) regulation mandatory requirement for Energy Efficiency Design Index (EEDI) has been in place and should be satisfied by newly-built ships of more than 400 gross tonnage and the Ship Energy Efficiency Management Plan (SEEMP) for all ships type. Therefore, compliance to this necessitates planning during the design stage whereas verification can be carried-out through an acceptable method during sea trial. The MEPC-approved 2013 guidance, ISO 15016 and ISO 19019 on EEDI serves the purpose for calculation and verification of attained EEDI value. Individual ships EEDI value should be lower than the required value set by these regulations. The key factors for EEDI verification are power and speed assessment and their synchronization. The shaft power can be measured by telemeter system using strain gage during sea trial. However, calibration of shaft power onboard condition is complicated. Hence, it relies only on proficient technology that operates within the permitted ISO allowance. On the other hand, the ship speed can be measured and calibrated by differential ground positioning system (DGPS). An actual test on a newly-built vessel was carried out to assess the correlation of power and speed. The Energy-efficiency Design Index or Operational Indicator Monitoring System (EDiMS) software developed by the Dynamics Laboratory-Mokpo Maritime University (DL-MMU) and Green Marine Equipment RIS Center (GMERC) of Mokpo Maritime University was utilized for this investigation. In addition, the software can continuously monitor air emission and is a useful tool for inventory and ship energy management plan. This paper introduces the synchronization and identification method between shaft power and ship speed for EEDI verification in accordance with the ISO guidance.

• The Journal of Korea Robotics Society
• /
• v.13 no.2
• /
• pp.86-91
• /
• 2018

This paper presents about design efforts of a human-sized quadruped robot leg for high energy efficiency, and verifications. One of the representative index of the energy efficiency is the Cost of Transport (COT), but increased in the energy or work done is not calculated in COT. In this reason, the input to the output energy efficiency should be also considered as a very important term. By designing the robot with customized motor housing, small rotational inertia, and low gear ratio to reduce friction, high energy efficiency was achieved. Squatting motion of one leg was performed and simulation results were compared to the experimental results for validation. The developed 50 kg robot can lift the weight up to 200 kg, and during squatting, it showed high energy efficiency. The robot showed 71% input to output energy efficiency in positive work. Peak current during squatting only appears to be 0.3 A.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.2
• /
• pp.369-376
• /
• 2021

The International Maritime Organization has developed the Energy Efficiency Design Index, an index related to carbon dioxide emissions, to enforce regulations on newly built ships. In this study, a new type of energy-saving device called the ring stator was used for 158k crude oil carriers, whose hull form was developed as a very thin after-body hull to reduce the resistance by delaying separation. The Energy-Saving Device (ESD) particularly involving the duct, is not adapted to the thin-after body hull form-like container ship. This new ring stator was developed considering these characteristics. A parametric study was conducted through Computational Fluid Dynamics (CFD) analysis using the Star-CCM+ program, and approximately 3.4 % improvement in propulsion efficiency was achieved. Further optimization investigations and experimental studies should be conducted in the future.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.3
• /
• pp.301-308
• /
• 2011

International Maritime Organization (IMO) proposed the Energy Efficiency Operation Indicator (EEOI) in 2005 and the Energy Efficiency Design Index (EEDI) in 2008 so as to address emission concern and regulation. Likewise, Ship Energy Efficiency Management Plan (SEEMP) and Greenhouse Gas (GHG) monitoring and management are also becoming an issue lately. This paper introduces the energy efficiency design index (operation indicator) monitoring system (EDiMS) software can continuously monitor $CO_2$, $NO_x$, $SO_x$, and PM values emitted from ship. The accurate inventory of ships GHG can be obtained from base of emission result during the engine shop test trial and the actual monitoring of shaft power and ship speed. In addition, the ability to store all exhaust emission and engine operation data can be applied as the useful tool of the inventory work of air pollution and ship energy management plan for the mitigation or reduction of ship emissions.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.14 no.1
• /
• pp.65-71
• /
• 2011

Since 2003, policies and practices related to the reduction of CO₂ gas emission from ships has been discussing by the International Maritime Organization. The representative emission index and indicator are the EEDI (Energy Efficiency Design Index) for the new ships and EEOI (Energy Efficiency Operational Indicator) during the voyage. For the CO₂ emission monitoring system, the SEEMP (Ship Energy Efficiency Management Plan) is also on the table. This global preparations to reduce theCO₂ emission is not except for the surface transportation. This research report elucidates the recent stream on the IMO CO₂ emission from ship and detail explanation on the EEDI and EEOI.

• Journal of Ocean Engineering and Technology
• /
• v.37 no.2
• /
• pp.58-67
• /
• 2023

While extensive research is being conducted to reduce greenhouse gases in industrial fields, the International Maritime Organization (IMO) has implemented regulations to actively reduce CO₂ emissions from ships, such as energy efficiency design index (EEDI), energy efficiency existing ship index (EEXI), energy efficiency operational indicator (EEOI), and carbon intensity indicator (CII). These regulations play an important role for the design and operation of ships. However, the calculation of the index and indicator might be complex depending on the types and size of the ship. Here, to calculate the EEDI of two target vessels, first, the ships were set as Deadweight (DWT) 50K container and 300K very large crude-oil carrier (VLCC) considering the type and size of those ships along with the engine types and power. Equations and parameters from the marine pollution treaty (MARPOL) Annex VI, IMO marine environment protection committee (MEPC) resolution were used to estimate the EEDI and their changes. Technical measures were subsequently applied to satisfy the IMO regulations, such as reducing speed, energy saving devices (ESD), and onboard CO₂ capture system. Process simulation model using Aspen Plus v10 was developed for the onboard CO₂ capture system. The obtained results suggested that the fuel change from Marine diesel oil (MDO) to liquefied natural gas (LNG) was the most effective way to reduce EEDI, considering the limited supply of the alternative clean fuels. Decreasing ship speed was the next effective option to meet the regulation until Phase 4. In case of container, the attained EEDI while converting fuel from Diesel oil (DO) to LNG was reduced by 27.35%. With speed reduction, the EEDI was improved by 21.76% of the EEDI based on DO. Pertaining to VLCC, 27.31% and 22.10% improvements were observed, which were comparable to those for the container. However, for both vessels, additional measure is required to meet Phase 5, demanding the reduction of 70%. Therefore, onboard CO₂ capture system was designed for both KCS (Korea Research Institute of Ships & Ocean Engineering (KRISO) container ship) and KVLCC2 (KRISO VLCC) to meet the Phase 5 standard in the process simulation. The absorber column was designed with a diameter of 1.2-3.5 m and height of 11.3 m. The stripper column was 0.6-1.5 m in diameter and 8.8-9.6 m in height. The obtained results suggested that a combination of ESD, speed reduction, and fuel change was effective for reducing the EEDI; and onboard CO₂ capture system may be required for Phase 5.

• Journal of the Society of Naval Architects of Korea
• /
• v.59 no.6
• /
• pp.372-384
• /
• 2022

Total shipping accounts for 2.9 % of the annual average percentage of global anthropogenic GHG emissions. The International Maritime Organization implements EEDI (Energy Efficiency Design Index), Energy Efficiency eXisting-ship Index (EEXI), and Carbon Intensity Indicator (CII) as regulatory frameworks for shipping decarbonization. The Republic of Korea has enforced the Act on Development and Popularization of Greenship from 2020 and publicly announced the 1st national plan which was named 『2030 Greenship-K Promotion Strategy』 for the activation of a greenship market. The Greenship Certification Scheme is going on for the sustainability of Korean shipbuilding and shipping industries, to secure clean maritime environments, as well as to contribute to the national economy. Greenship Certification guarantees the credit of such eco-friendly technologies and products for shipping. The certification is going to be the basis of industrial competitiveness in coastal and international shipping. This study investigates an existing certification process, identifies the limitations, and proposes the process improved with several case studies. The improved certification scheme may have rationality for Net-zero with regard to climate alignment.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.6
• /
• pp.843-851
• /
• 2009

Much work has already been done to control and regulate the worldwide problems caused by climate change, particularly the issues on greenhouse gas (GHG) emissions. Carbon dioxide ($CO_2$), having the highest form of concentration among GHGs composed around 1.0 billion tons of emission, and comprises about 98% of the total emissions from the shipping industry. Korean trade mainly rely on the sea transportation. Korean ship tonnages that was brought about by shipbuilders all over the country, continues to grow annually due to the prevailing demands on goods or material supplies and depicting only a small part of the global maritime activity. Nowadays, new build ships coming from the Korean Shipbuilders are being optimized by hull, structure and appendages design, The operational capability of the propulsion and auxiliary machineries in its maximum capacity to achieve the highest possible efficiencies for energy and onboard power use to mitigate $CO_2$ emissions are continually being done through the help of research and development. In this paper, the energy efficiency design index and anboard power capacity of Korean new build ships have been analyzed with response to data collected by ship types, and its respective fuel consumption in relation to $CO_2$ emission results. In response to climate change convention outcome proposals, the best way for the new build ships to become energy efficient is by lowering its operational speed thru adopting the state of the art diesel propulsion engines, patronizing the best sailing practice to lower the transportation cost on the different sea trade routes also helps in $CO_2$ mitigation.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.5
• /
• pp.627-633
• /
• 2019

This study aimed to predict the resistance and propulsion performance of a ship using computational fluid dynamics (CFD) and a database as well as establish an assessment method for the energy efficiency design index (EEDI) using the results. First, the total resistance of the studied ship is obtained using CFD. A flow analysis is conducted with the free surface and trim and sinkage using a commercial CFD code (STAR-CCM+). The effective power of the ship is assessed based on the CFD results. The quasi-propulsive efficiency is calculated from an empirical prediction equation using experimental data and similar material. Finally, a general calculation program for the EEDI is established based on the hydrodynamic results, ship information for principal particulars, conversion factor of $CO_2$ for fuels, and fuel consumption.

• ETRI Journal
• /
• v.44 no.1
• /
• pp.105-116
• /
• 2022

In this study, a novel group-indexed orthogonal frequency division multiplexing index modulation (OFDM-IM) scheme is proposed to achieve a tradeoff between spectral efficiency (SE) and bit-error-rate (BER) performance. In the proposed scheme, the total subcarriers in a group are divided into subgroups, and additional bits are transmitted by subgroup indexing, unlike the conventional OFDM-IM scheme, which uses index bits to select active subcarriers. With the proposed scheme, the additional degree of freedom provided by the number of active subgroups selected provides a tradeoff between spectral efficiency and BER performance. Decoding is performed in steps to reduce computional complexity in the decoder design. Simulaton results show that the number of active subgroups selected influences the proposed scheme's performance in terms of energy efficiency, spectral efficiency, and BER performance.