• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.9
• /
• pp.459-464
• /
• 2006

The detent force by end-effect has an undesired influence on moving coil type Permanent Magnet Linear Synchronous Motor(PMLSM). So, the reduction of detent force by end-effect is especially required for the improvement of thrust characteristics. In this paper, in order to reduce detent force by end-effect, the auxiliary-teeth is installed at the end part of mover. It is also analyzed by Finite Element Analysis(FEA) and optimized by using neural network. By comparison, the detent force is reduced about 41.4[%] comparing to that of basic model.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.33-35
• /
• 1994

In Linear Induction Motor(LIM), the end effect is caused by the abrupt change in the airgap magnetic reluctance at both ends of the machina Especially, in high speed, it has an adverse effect on various characteristics of LIM such as thrust, efficiency, power factor, etc. In this paper, we analyze the end effect, and describes the method to reduce end effect essentially and decrease the secondary material cost.

• Geomechanics and Engineering
• /
• v.23 no.6
• /
• pp.523-533
• /
• 2020

The current study focuses on the effect of the end shape of steel pipe piles on installation effort and bearing resistance using the pressing method of installation under dense ground conditions. The effect of pile rotation on the installation effort and bearing resistance is also investigated. The model steel piles with a flat end, cone end and cutting-edge end were used in this study. The test results indicated that cone end pile with the pressing method of installation required the least installation effort (load) and showed higher ultimate resistance than flat and cutting-edge end piles. However, pressing and rotation during cutting-edge end pile installation considerably reduces the installation effort (load and torque) if pile penetration in one rotation equal to the cutting-edge depth. Inclusion of rotation during pile installation reduces the ultimate bearing resistance. However, if penetration of the cutting-edge end pile equal to the cutting-edge depth in one rotation, the reduction in ultimate resistance can be minimized. In comparing the cone and cutting-edge end piles installed with pressing and rotation, the least installation effort is observed in the cutting-edge end pile installed with penetration rate equal to the cutting-edge depth per rotation.

• Journal of Power Electronics
• /
• v.11 no.5
• /
• pp.697-703
• /
• 2011

In this paper a control system with a high performance dynamic response for linear induction motors (LIMs) is proposed which takes into account the end-effect in both the machine model and the control system. Primary flux oriented control has two major drawbacks i.e. a lack of decoupling of the thrust and the flux and a possibility of system instability due to the end-effect. Both of these drawbacks have been dealt with in this paper. A flux estimation method is proposed to correct the flux orientation error caused by the end effect. Extensive motor performance evaluations under the proposed control system prove its superiority over conventional vector control.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.10
• /
• pp.35-42
• /
• 2003

In this paper, we classified the wavelength reservation mechanisms of optical burst switching (OBS), and investigated the path length priority effect of the offset time/delayed reservation (OT/DR)-based scheme like the just-enough-time (JET) protocol. And, we showed that the fiber delay line (FDL)-based scheme can avoid the path length priority effect in multiple hop network environments. Also, we proposed a novel FDL/DR with hop-by-hop priority increasing (HPI) scheme which can improve the end-to-end throughput by increasing the priority of bursts hop-by-hop using the input FDLs at each node. The simulation results showed that the proposed FDL/DR with HPI scheme could avoid the path length priority effect and enhance the end-to-end throughput in multiple hop network environments.

• Korean Journal of Veterinary Research
• /
• v.26 no.2
• /
• pp.265-276
• /
• 1986

The bovine serum factor influencing the growth of swine testicle (ST) cell and the END effect of hog cholera SN test was studied. Throughout the experimental studies. following results were obtained and summarized. 1. Bovine whole serum of 16(76.2%) and 4(19.0%) samples out of 21 have shown a positive ST cell growth and the END effect, respectively. However, all of 21(100%) and 8(38.1%) samples out of 21 serum supernatant fractions, prepared from the bovine whole serum, have shown positive ST cell growth and END effect, respectively. 2. In the SDS-polyacrylamide gel electrophoretic analysis of the bovine whole serum and the supernatant fractions, ST cell growth inhibiting factor was proved present in globulin fraction and in whole gel plate as a diffusible component. 3. The END ineffective component present in the whole serum and its supernatant fraction was proved to be BVDV neutralizing antibody. 4. The difference of osmolarity, optical density, pH, degree of precipitant formation following heat cold treatment, A/G ratio as we11 as electrophoretic pattern and NDV SN index of the samples were not correlated to the degree of 57 cell growth and to the END effectiveness.

• Proceedings of the KIEE Conference
• /
• 2006.04b
• /
• pp.115-117
• /
• 2006

The detent force by end-effect has a bad influence on moving coil type Permanent Magnet Linear Synchronous Motor(PMLSM). So, the reduction of detent force by end-effect is especially required for improvement of thrust characteristics. In this paper, in order to reduce detent force by end-effect the auxiliary teeth is installed at the end part of mover and it is optimized by using neural network.

• Proceedings of the KIEE Conference
• /
• 2003.10b
• /
• pp.33-35
• /
• 2003

This paper proposes inserted core type of slotless Permanent Magnet Linear Synchronous Motor(PMLSM) to improve its low thrust density. However, by inserting the core between windings of each phase, detent force is generated. Furthermore, linear motors have the feature of structurally limited length. So, it causes the end-effect in actual operation. So, this paper applies the neural network to this model to minimize detent force and maximize thrust. Also, sub-poles used the to the end parts of the mover for compensating the end-effect.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.4
• /
• pp.38-45
• /
• 1997

A new dynamic model for the cutting process inb the end milling process is developed. This model, which describes the dynamic response of the end mill, the chip load geometry including tool runout, the dependence of the cutting forces on the chip load, is used to predict the dynamic cutting force during the end milling process. In order to predict accurately cutting forces and tool vibration, the model which uses instantaneous specific cutting force, inclueds both regenerative effect and penetration effect, The model is verified through comparisons of model predicted cutting force with measured cutting force obtained from machining experiments.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.9
• /
• pp.525-531
• /
• 2004

This paper proposes inserted core type of slotless Permanent Magnet Linear Synchronous Motor(PMLSM) to improve its low thrust density. However, by inserting the core between windings of each phase, detent force is generated and it acts as thrust ripple. Furthermore, linear motors generate end effect making thrust ripple. So, this paper applies the neural network to minimize detent force and to maximize thrust. Also, sub-poles is placed at the end parts of the mover to compensate end effect. To confirm of calculation method's validity, the calculated results are compared with experimental results.