• Journal of ILASS-Korea
• /
• v.23 no.3
• /
• pp.122-127
• /
• 2018

Recently, registrated passenger cars have increased and were close about seventy million at the end 2017 year in Korea. Among the passenger car using gasoline fuel make up forty six percentage of total registrated vehicles. In this study, investigation on real driving emission characteristics in the passenger car using gasoline fuel with various engine displacements were carried out. The real driving emission characteristics were measured and analyzed by using PEMS (Portable Emission Measurement System). PEMS was composed of gas analyzer, emission flow meter and sample conditioning system et al. Also, test six vehicles were selected to the gasoline passenger car with engine displacement from 1.6L to 3.7L. Two test routes with engine start of cold and hot conditions were applied to analyze the emission characteristics of RDE, respectively. The results show that the $CO_2$ emission have a increasing trend as the engine displacement and vehicle weight. Also, it is guessed that the $CO_2$ emission and vehicle weight were more correlated than the engine displacements. On the other hand, NOx emissions of RDE have not increasing or decreasing tendency according engine displacements or vehicle weight because the activation of three-way catalyst in the gasoline vehicles.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.2
• /
• pp.220-224
• /
• 2017

Nitrogen dioxide ($NO_2$) is an important urban pollutant in Korea. Expecially, diesel vehicles are responsible for the most traffic rated nitrogen oxide ($NO_X$) emission, including nitric oxide (NO) and nitrogen dioxide ($NO_2$). Though nitrogen oxide ($NO_X$) emission from vehicle was applied a strict enforcement of emission standard, the specific $NO_2$ fraction in $NO_X$ ($NO_2/NO_X$) from various types of diesel vehicles was not understood. In order to investigate the fraction of $NO_2/NO_X$, the vehicle emission study was carried out at the facility of Transport Pollution Research Center (TPRC), National Institute of Environmental Research (NIER), Korea. Three different types of diesel vehicles(VAN, SUV, passenger) were tested on the NIER driving mode. The result of $NO_2/NO_X$ ratio was over 0.1 for all test vehicles and the highest $NO_2$ emission was observed at the van vehicle. The observation was showed that the emission trend of $NO_2/NO_X$ for passenger and SUV vehicles were inversely proportional. Also, as the emission standard has been strengthen, the emission rate of $NO_2$ has been decrease.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3383-3388
• /
• 2007

To compare the sensor performance of AE leak diagnosis system which can measure valve leak conditions, AE activities such as RMS voltage level, AE signal trend, leak rate degree according to AE database, FFT spectrum were measured on valve of the simulated test system for power plant. AE activities were recorded and analyzed from various operating conditions including different temperature, pressure difference, valve size and fluid using both piezoelectric acoustic emission sensor and Pb-Free acoustic emission sensor. The results of this study are utilized to select the type of sensors, the frequency band for filtering and thereby to improve the signal-to-noise ratio for diagnosis or monitoring of valves in operation. As the final result of application study above, portable type leak diagnosis system by AE was developed. The outcome of the study can be definitely applied as a means of the diagnosis or monitoring system for energy saving and prevention of accident for power plant valve.

• Proceeding of Spring/Autumn Annual Conference of KHA
• /
• 2006.11a
• /
• pp.275-280
• /
• 2006

The protection of the environment is one of today's key demanding international activities and interests. All of aspects including industry, economy and society should be changed into environmental friendly industries. The building is not exception in this trend. What is not generally realized is that building, in the lifecycle of construction, use and demolition, account for large construction, not considered with environment impact and conservation in the lifecycle. Expecially, the construction materials and components used in the construction stage has much embodied energy. And much $CO_2$ emit on the production of the construction material and component. The energy use and $CO_2$ emission would continuously diminish the limited natural resources and impact the environment such as ozon layer destruction. In this paper, it studied the estimation of the amount of energy use and $CO_2$ emission in the building construction stage, it would provide the estimation process and applied with the multifamily housing.

• Journal of ILASS-Korea
• /
• v.20 no.4
• /
• pp.207-216
• /
• 2015

Recently, the researches for air pollutant control technologies have been performing in Korea, while considering an one of the latest main topics as problems on air pollutant control. However, it is difficult to investigate emission amount of air pollutant by passenger cars, because of lack of the domestic information about mobile source; the number of research institutes are less in the whole. Especially, the informations on registered numbers and emissions of motorcycles are less. Thus, in this study, the analysis that is based on experimental results was conducted for finding out source profiling and emission characteristics on motorcycles exhaust. For these experiments, the domestic motorcycles were chosen and evaluated by EURO III standard. From the result, controlled pollutants (CO, HC, NOx) were met to EURO III, but low displacement motorcycles showed a higher incomplete combustion reaction than that of 250 cc motorcycles. Additionally, uncontrolled pollutants (BTEX and 1,3-butadiene) were decreased with increasing a displacement of motorcycles. However, the emission trend of aldehydes was not followed that of those; the formaldehyde ratio increased upto approximately 33%, with increasing a displacement of motorcycles. In the future, it would be used to support the CAPSS as basic data of Korea.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.11
• /
• pp.26-32
• /
• 2011

In this study, a standard illuminant A type LED that has similar emission spectrum as the standard illuminant A was developed using LED chip(emission peak: 405[nm]) and four types of phosphors(blue, green orangered and red). Using the design of experiment for spectrum control, the trend of the change of spectrum shape influenced by the change of interaction among phosphors and their density could be examined. Computer simulation through the optimization of the design of experiment revealed that, among four phosphors, the most influential one on the shape of the spectrum was green phosphor. Using the obtained optimal combination ratio of the four phosphors, an alternative LED illuminant to the actual standard illuminant A was developed and the spectrums of these two were confirmed identical. Using this standard illuminant A type LED, a portable transmittance meter with the range of measurement error of ${\pm}1.0$[%] was developed.

• Geomechanics and Engineering
• /
• v.25 no.2
• /
• pp.135-142
• /
• 2021

This study provided a new research perspective for processing and analyzing AE data to evaluate rock failure. Cluster method and information entropy theory were introduced to investigate temporal and spatial correlation of acoustic emission (AE) events during the rock failure process. Laboratory experiments of granite subjected to compression were carried out, accompanied by real-time acoustic emission monitoring. The cumulative length and dip angle curves of single links were fitted by different distribution models and distribution functions of link length and directionality were determined. Spatial scale and directionality of AE event distribution, which are characterized by two parameters, i.e., spatial correlation length and spatial correlation directionality, were studied with the normalized applied stress. The entropies of link length and link directionality were also discussed. The results show that the distribution of accumulative link length and directionality obeys Weibull distribution. Spatial correlation length shows an upward trend preceding rock failure, while there are no remarkable upward or downward trends in spatial correlation directionality. There are obvious downward trends in entropies of link length and directionality. This research could enrich mathematical methods for processing AE data and facilitate the early-warning of rock failure-related geological disasters.

• Structural Engineering and Mechanics
• /
• v.89 no.6
• /
• pp.617-626
• /
• 2024

The study investigated the behavior of plain and fibered Ultra-High Performance Concrete (UHPC) beams under varying loading conditions using integrated analysis of the flexure and acoustic emission tests. The loading rate of testing is -0.25 -2 mm/min. It is observed that on increasing loading rate, flexural strength increases, and toughness decreases. The acoustic emission testing revealed that higher loading rates accelerate crack propagation. Fiber effect and matrix cracking are identified as significant contributors to the release of acoustic emission energy, with fiber rupture/failure and matrix cracking showing rate-dependent behavior. Crack classification analysis indicated that the rise angle (RA) value decreased under quasi-static loading. The average frequency (AF) value increased with the loading rate, but this trend reversed under rate-dependent conditions. K-means analysis identified distinct clusters of crack types with unique frequency and duration characteristics at different loading rates. Furthermore, the historic index and signal strength decreased with increasing loading rate after peak capacity, while the severity index increased in the post-peak zone, indicating more severe damage. The sudden rise in the historic index and cumulative signal strength indicates the possibility of several occurrences, such as the emergence of a significant crack, shifts in cracking modes, abrupt failure, or notable fiber debonding/pull-out. Moreover, there is a distinct rise in the number of AE knees corresponding to the increase in loading rate. The crack mapping from acoustic emission testing aligned with observed failure patterns, validating its use in structural health monitoring.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.470-473
• /
• 2004

This paper presents conducted emission noise measurement from electronic equipment in frequency range of 1 MHz up to 30 MHz by small loop antenna. Small loop antenna measurement method can measure common-mode (CM) and differential-mode (DM) component of the noise on a pair of power line at the same time. The CM and DM can be measured separately. The theory of this measurement method is introduced and analyzed. The measured results were compared with the conventional measurement by Line Impedance Stabilization Network (LISN) and result a good trend between those methods.

• Journal of Forest and Environmental Science
• /
• v.28 no.3
• /
• pp.194-198
• /
• 2012

In order not to hinder the trend of promoting participatory forest management under the REDD-plus mechanism, we propose a simple method to support local stakeholders evaluating and selecting promising national programs as REDD-plus activities prior to the launch of activities. Program evaluation is done from the viewpoint of expectations for achieving (1) 'triple-benefit' consisting of emission reduction from mitigating deforestation and forest degradation, biodiversity conservation, and poverty alleviation, and (2) 'feasibility' when the programs would be practiced on the ground. The method is applicable for other countries.