• 유공압시스템학회논문집
• /
• 제8권3호
• /
• pp.1-7
• /
• 2011

As the technologies of electronic device have advanced these days, most of mechanical systems are designed with electronic control unit to take advantage of control parameter adaption to operating conditions and firmware flexibilities as well. On-board diagnosis, which detects the system malfunction and identifies potential source of error with its own diagnostic criteria, and fail-safe that can switch the mode of operation in view of recognized error characteristics enables easy maintenance and troubleshooting as well as system protection. This paper dealt with the development of diagnosis and fail-safe function for proportional flow control valve. All type of errors related to valve control system components are investigated and assigned to a specific hexadecimal codes. Cumulative error detection algorithm is applied in order for the sensitivity and reliability to be appropriate. Embedded simulator which runs simultaneously with system program provides the virtual error simulation environment for expeditious development of error detection algorithm. The diagnosis function was verified both with solenoid valve and embedded simulator test and it will enhance the valve control system monitoring function.

• 전자공학회논문지A
• /
• 제31A권10호
• /
• pp.141-151
• /
• 1994

this paper describes the design and implementation of a RISC processor for embedded control systems. This RISC processor integrates a register file, a pipelined execution unit, a FPU interface, a memory interface, and an instruction prefetcher. Its characteristics include both single cycle executions of most instructions in a 2 phase 20 MHz frequency and the worst case interrupt latency of 7 cycles with the vectored interrupt handling that makes it possible to be applicable to the real time processing system. For efficient handling of multi-cycle instructions, data stationary hardwired control scheme equippedwith cycle counter was used. This chip integrates about 139K transistors and occupies 9.1mm$\times$9.1mm in a 1.0um DLM CMOS technology. The power dissipation is 0.8 Watts from a 5V supply at 20 MHz operation.

• 대한임베디드공학회논문지
• /
• 제11권2호
• /
• pp.79-86
• /
• 2016

In wireless sensor networks, increasing the sensing rate of each node to improve the data accuracy usually incurs a decrease of network lifetime. In this study, an energy-adaptive data compression scheme is proposed to efficiently control the sensing rate in an energy-harvesting wireless sensor network (WSN). In the proposed scheme, by utilizing the surplus energy effectively for the data compression, each node can increase the sensing rate without any rise of blackout time. Simulation result verifies that the proposed scheme gathers more amount of sensory data per unit time with lower number of blackout nodes than the other compression schemes for WSN.

• 대한임베디드공학회논문지
• /
• 제19권3호
• /
• pp.123-130
• /
• 2024

This paper proposes an EMPC (Explicit Model Predictive Controller) for temperature tracking control based on heat load prediction by an ESO (Extended State Observer) for a variable cooling circulation system with multiple indoor units connected to one outdoor unit. In this system, heat transfer and heat loss relative to the input temperature are modeled using system dynamics. Using this model, we design an EMPC based on an ESO that is robust to temperature changes and depends on airflow. To determine the stability of both the controller and the observer, asymptotic stability is verified through Lyapunov stability analysis. Finally, to validate the performance of the proposed controller, simulations are conducted under three scenarios with varying airflow, set temperature, and heat load.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1042-1045
• /
• 2003

In this paper, we present a new method for the monitoring of Electric Control Unit's(ECU) self-diagnostic and the sensor signals of vehicle through Web. In order to measure the ECU's self-diagnostic and sensor signals, the interfaced circuit is designed to communicate ECU and terminal according to the ISO, SAE regulation of communication protocol standard. Microprocessor 80C196KC is used for communicating ECU's self-diagnostic signals and the results are sent to the Embedded Linux System(ELS) through RF module. ELS is developed by SA1110, RF module, Embedded Linux. All commands related in ECU communication are executed through Web. The CGI program composed in web server is executed by user and will return sensor signals from ECU Software on Embedded Linux system is developed to monitor the ECU's sensor signals using the arm compiler tool chain in which RS232 port is programmed by half duplex method. The possibility for remote measurement of ECU sensor signal through Web is verified through the developed systems and algorithms.

• 전자공학회논문지
• /
• 제51권9호
• /
• pp.238-247
• /
• 2014

착유로봇 시스템은 움직이는 젖소의 유두 위치를 정확하게 검출해야 하고, 로봇 매니퓰레이터는 검출된 유두 위치값을 추적하여 착유컵이 유두에 장착하도록 제어되어야 한다. 제안된 착유로봇 매니퓰레이터는 위치검출 레이저 센서를 이용하여 유두를 스캐닝하고 임베디드 구동제어장치를 통하여 독립된 3축 브러쉬리스 서보 구동제어 메커니즘에 의하여 구현된다. 이 로봇 매니퓰레이터는 유두 위치검출용 레이저센서, 4개의 착유컵, 3축 x, y, z축의 매니퓰레이터, g축 방향 이송기능을 가진 유두인 식장치와 착유컵 구동장치, 임베디드 구동제어장치와 자동 밀크 제어라인으로 구성된다. 제안된 로봇시스템은 구동시스템 전체가 전기구동방식으로 설계되어 있기 때문에 구조가 간단하고, 저가로 제작이 가능하며, 구동시에 소음이 적기 때문에 젖소의 심적 안정성을 줄 수 있는 장점을 가지고 있다. 설계된 로봇은 축산과학원 농장에서 젖소를 대상으로 실험을 실시하였으며, 실험결과에 의하여 설계사양의 성능조건이 만족됨을 확인하였다.

• 드라이브 ㆍ 컨트롤
• /
• 제14권4호
• /
• pp.29-36
• /
• 2017

Electronic control technologies that have long been developed for passenger cars spread to construction equipment and agricultural vehicles because of its outstanding performance achieved by embedded software. Especially, system program of transmission control unit (TCU) plays a crucial role for the superb shift quality, driving performance and fuel efficiency, etc. Since the control algorithm is embedded in software that is rarely analyzed, development of such a TCU cannot be conducted by conventional reverse engineering. Transmission simulator is a kind of electronic device that simulates the electric signals including driver operation command and output of various sensors installed in transmission. Standalone TCU can be run in normal operation mode with the signals provided by transmission simulator. In this research, transmission simulator for the tracked vehicle TCU is developed for the analysis of shift control algorithm from the experiments with standalone TCU. It was confirmed that shift experimental data for the simulator setup conditions can be used for the analysis of control algorithms on proportional solenoid valves and shift map.

• 전기전자학회논문지
• /
• 제21권4호
• /
• pp.408-411
• /
• 2017

본 논문에서는 중성자, 감마선, 엑스선 등의 방사선을 측정하는 통합 제어 시스템을 제안한다. 제안하는 시스템은 원격 또는 네트워크상으로 측정 및 분석한 데이터를 디스플레이를 통해 모니터링 및 제어할 수 있는 장비로서, 현장에 가지 않고도 시스템 각 구성 부분의 상태를 보고 변경하여 원격으로 감시 및 관리할 수 있다. 제안하는 시스템은 감마선/엑스선 센서부, 중성자 센서부, 주제어 임베디드 시스템부, 전용 디스플레이 장치 및 GUI부, 원격 UI부 등으로 구성된다. 감마선/엑스선 센서부는 NaI(Tl) Scintillation Detector를 사용하여 저준위의 감마선 및 엑스선을 측정한다. 중성자 센서부는 Proportional Counter Detector(저준위 중성자)와 Ion Chamber Type Detector(고준위 중성자)를 사용하여 중성자를 측정한다. 주제어 임베디드 시스템부는 방사선을 검출하여 초단위로 샘플링하고 누적된 펄스 및 전류값에 대한 방사선량으로 변환한다. 전용 디스플레이 장치 및 GUI부는 방사선 측정 결과와 변환된 방사선량 및 방사능량 측정 수치를 출력하고, 사용자에게 제어 조건 설정 및 검출부에 대한 캘리브레이션 기능을 제공한다. 원격 UI부는 측정된 값들을 취합, 저장하여 원격 감시 시스템에 전달한다. 제안된 시스템의 성능을 평가하기 위하여 공인시험기관에서 실험한 결과는 중성자 검출부는 ${\pm}8.2%$ 이하의 측정 불확도가 측정되었고, 감마선, 엑스선 검출부는 7.5%이하의 불확도가 측정되어 국제 표준인 ${\pm}15%$ 이하에서 정상동작 됨이 확인되었다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.138-142
• /
• 2004

In this paper, we present a new method for monitoring of ECU's sensor signals of vehicle. In order to measure the ECU's sensor signals, the interfaced circuit is designed to communicate ECU and the Embedded Linux is used to monitor communication result through Web the Embedded Linux system and this system is said "ECU Interface Part". In ECU Interface Part the interface circuit is designed to match voltage level between ECU and SA-1110 micro controller and interface circuit to communicate ECU according to the ISO, SAE communication protocol standard. Because Embedded Linux does not allow to access hardware directly in application level, anyone who wants to modify any low level hardware must develop device driver. To monitor ECU's sensor signals the most important thing is to match serial level between ECU and ECU Interface Part. It means to communicate correctly between two hardware we need to match voltage and signal level, and need to match baudrate. The voltage of SA-1110 is 0 ${\sim}$ +3.3V and ECU is 0 ${\sim}$ +12V and, ECU's communication Line K does multiple operation so, the interface circuit is used to match voltage and signal level. In Addition to ECU's baudrate is 10400bps, it's not standard baudrate in computer environment. So, we need to develop a device driver to control the interface circuit, and change baudrate. To monitor ECU's sensor signals through web there's a network socket program is working in Embedded Linux. It works as server program and manages user's connections and commands. Anyone who wants to monitor ECU's sensor signals he just only connect to Embedded Linux system with web browser then, Embedded Linux webserver will return the ActiveX webbased measurement software. It works in web browser and inits ECU, as a result it returns sensor signals through web. All the programs are developed with GCC(GNU C Compiler) and, webbased measurement software is developed with Borland C++ Builder.

• 전기전자학회논문지
• /
• 제22권4호
• /
• pp.1214-1217
• /
• 2018

본 논문에서는 소형 $360^{\circ}$ 구강 스캐너 임베디드 보드의 개발을 제안한다. 제안하는 소형 $360^{\circ}$ 구강 스캐너 임베디드 보드은 이미지 레벨 및 전송방식 변경 부, FPGA 부, 메모리 부, FIFO to USB 전송부 등으로 구성된다. 이미지 레벨 및 전송방식 변경 부는 소형 $360^{\circ}$ 전방위 구강 렌즈와 이미지 센서를 통해 들어온 MIPI 형식의 구강 영상을 Low Power Signal Mode와 High Speed Signal Mode로 나누어 포트에 분산 입력하고 레벨 시프트를 하여 FPGA 부에 전송한다. FPGA 부에서는 $360^{\circ}$ 영상 왜곡 보정, 영상 보정, 영상 처리, 영상 압축 등의 기능 등을 수행한다. FIFO to USB 전송부에서는 FPGA 내부의 FIFO를 통해 전달되어진 RAW 데이터를 트랜시버 칩을 사용하여 USB 3.0, USB 3.1 등의 통신 규격으로 PC에 전송한다. 제안된 소형 $360^{\circ}$ 구강 스캐너 임베디드 보드의 효율을 판단하기 위하여 공인시험기관에서 실험한 결과, 보정 영상 후 초당 프레임은 60fps 이상, 데이터 전송률은 4.99Gb/s로서 높은 수준의 결과가 산출되어 그 효용성이 입증되었다.