• The Korean Journal of Ceramics
• /
• 제4권4호
• /
• pp.331-335
• /
• 1998

R-curve, of three kinds of silicon nitride-based ceramics were measured, using single edge notched beam (SENB) method at room and at elevated temperatures, up to $1200^{\circ}C$. Stable fraacture was seen on ceramic materials with SENB specimens if the machined notch is deep enough, even though the crack resistance did not increase with crack length. Hot pressed silicon nitride did not show the rising R-curve behavior at room temperature, but it showed some rising at $1000^{\circ}C$ and above. Si3N4 reinforced with SiC whiskers showed no rising behavior at room and elevated temperatures, as it has smaller grain size, compare to the monolithic specimen. Gas pressure sintered silicon nitride had very large and elongated grains, and it showed rising R-curve even at room temperature. However, it showed some creep behavior at $1200^{\circ}C$ and the calculated R-curve on this condition did not show a good result. We cannot apply this technique on this condition for obtaining the R-curve.

• Journal of Magnetics
• /
• 제11권3호
• /
• pp.103-107
• /
• 2006

In grain oriented electrical steel process, hot band annealing has thought to be essential for obtaining good magnetic properties. New hot rolling method of heavy reduction in early hot rolling stage was applied to obtain good magnetic properties in GO process without hot band annealing. Hot rolling was carried out by varyinghot rolling reduction distribution along hot rolling pass. The heavy hot rolling reduction in rear stand improves the magnetic flux density in the case of no hot band annealing. The hot band specimens of the heavy reduction in front stand shows the elongated hot deformed microstructures in the center layer and strong {001}<110> texture.On the contrary, the heavily reduced specimens in rear stand shows the recrystallization in the center layer of hot band and strong {111}<112> and {110}<001> textures.

• 소성∙가공
• /
• 제12권6호
• /
• pp.558-565
• /
• 2003

Rotary swaging is one of the incremental forming process which is a chipless metal forming process for the reduction of cross-sections of bars, tubes and wires. In the present work, the rotary swaging machine and dies were designed to investigate the formability of TDS(Tube Drive Shaft) used in automotive industry. The process variables such as the speed of forming, the shape of the formed materials and the reduction of area were also estimated to study experimental analyses of rotary swaging process using the materials of 34Mn5 and S45C. From experimental results, it was found that the process variables affected the quality of TDS in terms of hardness, the precision of products and the surface roughness. The hardness after swaging approved to be Increased with the increase in the reduction of diameter. And it was found that the grain size became smaller and the elongated grains were formed in the axis direction.

• 한국세라믹학회지
• /
• 제41권2호
• /
• pp.125-130
• /
• 2004

서로 다른 크기의 SiC 원료분말을 첨가한 A1$_2$O$_3$-SiC 복합재료의 미세조직과 그에 따른 기계적 물성의 변화를 관찰하였다. 0.15 $mu extrm{m}$의 SiC가 첨가된 복합재료의 경우 기지상의 입성장이 효과적으로 억제되었다 그러나, 소수의 비정상입자가 생성된 이후에는 이들 입자의 급격한 성장으로 불규칙한 형상의 커다란 입자로 구성된 미세조직을 보이며, 파괴강도값은 급격히 감소하였다. 3 $\mu\textrm{m}$의 SiC가 첨가된 경우에는 기지상의 입성장이 일어났으나, 소수의 비정상입자가 생성된 이후에는 과도한 입성장은 억제되고 일정한 크기의 비정상입자가 시편 전체에 균일하게 형성된 미세조직을 보였다. 한편, 0.15 $\mu\textrm{m}$와 3 $\mu\textrm{m}$의 SiC 입자를 동시에 첨가한 시편은 균일한 크기의 비정상입성장의 미세조직을 보였으나, 비정상입성장이 일어났음에도 불구하고 기계적 물성은 우수하게 유지되었다 즉, 비정상입성장에 의해 미세조직에는 큰 변화가 일어났으나, 파괴강도값에는 변화가 없었다.

• 한국결정성장학회지
• /
• 제7권1호
• /
• pp.18-26
• /
• 1997

소결조제로 Y 3Alo012를 첨가한 {3- SiC 분말에 seed로서 1 wt%의 a- SiC 분말을 첨 가한 시편과 첨가하지 않은 시편을 1950$^{\circ}$C, argon 분위기에서 0.5~4시간 동안 소결하였다. S Seed로써 1 wt% a-SiC 분말의 첨가는 소결 도중에 길게 자란 업자틀의 성장을 가속시켰고, a a- SiC seed를 첨가한 시편에서 더 조대한 미세구조가 얻어졌다 .. a-SiC seed를 첨가하여 4시간 동안 소결한 시편의 파괴인성은 7.5 MPa'ml/2이었고, seed를 첨가하지 않은 시편의 파괴인성은 6 6.1 MPa'm1/2이었다 .. Seed를 첨가한 시편의 높은 파괴인성은 조대한 미세구조에 포함된 길게 자란 입자들에 의한 균열가교 기구의 활발한 작용에 기인한다.

• Journal of Welding and Joining
• /
• 제28권6호
• /
• pp.70-75
• /
• 2010

This study intends to investigate the weldability and mechanical characteristics of butt weld joints by LAFSW for dissimilar materials (Al6061-T6 and SS400). At optimum welding conditions, the tensile strength of dissimilar materials joints made by FSW is found to be lower than that of LAFSW. Due to the increase in plastic flow and formation of finer recrystallized grains at the TMAZ and SZ by laser preheating in LAFSW, the hardness in LAFSW appeared to be higher than that of FSW. Compared with FSW, finer grain size is observed and elongated grains in parent metal are deformed in the same direction around the nugget zone in TMAZ of Al6061-T6 by LAFSW. Whereas, at weld nugget zone, coarse grain size is appeared in LAFSW compared to FSW, which is owing to more plastic flow due to laser preheating effect. In dissimilar materials joints by LAFSW, ductile mode of fracture is found to occur at Al6061 side with fewer brittle particles. Mixed mode of cleavage area and ductile fracture is observed at SS400 side.

• 한국주조공학회지
• /
• 제23권2호
• /
• pp.77-85
• /
• 2003

Some alloying elements such as Cr, B, Ti and Si were added individually or as a mixture to Fe-30 at.%Al alloys. The alloys were melted using an arc furnace and then heat-treated for homogenization at 1000$^{\circ}C$ for 7 days and followed by rolling at 1000$^{\circ}C$. The alloying elements on rolling characteristics were investigated by the microstructures and fracture mode before and after rolling. The microstructures before rolling showed that all of the alloys had equiaxed grains. On the other hand, the microstructures of rolling plane as well as its perpendicular plane became elongated after rolling. The alloys such as Fe-30Al, Fe-30Al-3Ti, Fe-30Al-0.5B, Fe-30Al-5Cr and Fe-30Al-3Ti-0.5B revealed better rolling behaviour from the point that intergranular and cleavage fractures were not fundamentally occurred. But the addition of 5Ti or 3Si to Fe-Al alloys had detrimental effects. The Ti-added alloy system such as Fe-30Al-5Ti, Fe-30Al-5Ti-5Cr, Fe-30Al-3Ti-5Cr and Fe-30Al-5Ti-0.5B were cracked through grain and showed cleavage fracture. The Si-added alloy system such as Fe-30Al-5Si, Fe-27Al-3Si and Fe-27Al-5Cr-3Si were cracked along the grain boundary and showed intergranular fracture. $DO_3{\leftrightarrow}B_2$ transition temperature of Fe-30at.%Al alloy was 520$^{\circ}C$, whereas the addition of 3Ti and 3Ti+0.5B comparably increased the temperature to 797 and 773$^{\circ}C$, respectively.

• 한국재료학회지
• /
• 제4권2호
• /
• pp.241-249
• /
• 1994

항공기용 고력 AI합금인 7075 AI합금의 물성개선을 위한 가공열처리 방안으로서 과시효처리후 온간 및 냉간 압연에 의한 소성가공이 재결정조직과 강도에 미치는 영향에 대하여 연구하였다. 소송가공후 재결정처리에 의해 결정립을 미세화하는 공정에서 소성가공 전 과시효를 함으로써 재결정립의 미세화 정도는 더욱 현저하였다. 이는 과시효에 의한 조대한 석출물이 재결정처리시 핵생성 site로서 작용하였음을 의미한다. 본 연구에서 항복강도와 재결정립의 크기와는 Hall-petch식을 만족하지 않았으며 이는 등축이 아닌 연신된 결정조직에 기인된 결과로 보이며, 항복강도가 재결정립의 종횡비에 직선적으로 비례하였다. 또한 결정립 미세화를 통한 강도, 인성향상을 목적으로 하는 TMT(Thermo mechanical Treatment)공정에서는 심한 냉간가공에 의해서보다는 온간에서의 소성가공이 바람직함을 알 수 있었다.

• 대한금속재료학회지
• /
• 제49권6호
• /
• pp.474-487
• /
• 2011

Bars of OFHC Cu with the diameter of 45 mm were processed by equal channel angular pressing up to 16 passes via route $B_c$, and homogeneity of their microstructures and mechanical properties was examined at every four passes which develop the equiaxed ultrafine grains. In general, overall hardness, yield strength and tensile strength increased by 3, 7, and 2 times respectively compared with those of unECAPed sample. Cross-sectional hardness exhibited a concentric distribution. Hardness was the highest at the center of bar and it decreased gradually from center to surface. After 16 passes, overall hardness decreased due to recovery and partial recrystallization. Regardless of the number of passage, yield strength and tensile strength were quite uniform at all positions, but elongation showed some degree of scattering. At 4 passes, coarse and ultrafine grains coexisted at all positions. After 4 passes, uniform equiaxed ultrafine grains were obtained at the center, while uniform elongated ultrafine grains were manifested at the upper half position. At the lower half position, grains were equiaxed but its size were inhomogeneous. It was found that inhomogeneity of grain morphology and grain size distribution at different positions are to be attributed to scattering in elongation but they did not affect strength. The present results reveal the high potential of practical application of equal channel angular pressing on fabrication of large-sized ultrafine grained bars with quite homogeneous mechanical properties.

• 한국재료학회지
• /
• 제33권9호
• /
• pp.367-371
• /
• 2023

In this study we examine variations in the structure of perovskite compounds of LaBa₂Cu₂O₉, LaBa2₂CaCu₃O₁₂ and LaBa₂Ca₂Cu₅O₁₅ synthesized using the solid state reaction method. The samples' compositions were assessed using X-ray fluorescence (XRF) analysis. The La: Ba: Ca: Cu ratios for samples LaBa₂Cu₂O₉, LaBa2₂CaCu₃O₁₂ and LaBa₂Ca₂Cu₅O₁₅ were found by XRF analysis to be around 1:2:0:2, 1:2:1:3, and 1:2:2:5, respectively. The samples' well-known structures were then analyzed using X-ray diffraction. The three samples largely consist of phases 1202, 1213, and 1225, with a trace quantity of an unknown secondary phase, based on the intensities and locations of the diffraction peaks. According to the measured parameters a, b, and c, every sample has a tetragonal symmetry structure. Each sample's mass density was observed to alter as the lead oxide content rose. Scanning electron microscope (SEM) images of the three phases revealed that different Ca-O and Cu-O layers can cause different grain sizes, characterized by elongated thin grains, without a preferred orientation.