• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.05a
• /
• pp.108-110
• /
• 1994

Decomposition products by crosslinking reaction of PE using Dicumylperoxide(DCP) should influence on the electrical properties in XLPE. This paper studies on Behaviors of Decomposition products and Electrical Treeing ding to Drying condition. We used the Gas Chromatography for Decomposition Gases analysis FT-IR for investigating the behaviors of Decomposition products remained in XLPE Break Down Voltage Tester for Electrical Treeing measurement.

• Journal of the Korea Safety Management & Science
• /
• v.26 no.1
• /
• pp.31-38
• /
• 2024

In this paper, as there are many cases of fires occurring due to the failure or inoperability of the thermostat of electronic products, the purpose is to test and analyze the risks and probabilities through fire cases and reproduction experiments, and suggest countermeasures. Among electronic products, water purifiers are composed of a refrigerant system with a compressor to make cold water, a heating device to make hot water, and an electric device used as an energy source. Due to the nature of the water purifier manufacturing, these devices are subject to a lot of moisture and dust. etc. exist in large quantities and use electrical energy, so there is a possibility of fire due to short circuit in the wire, electrical abnormal overheating (tracking phenomenon) in the thermostat, electronic board, starting relay, etc., and overheating of the heating device (Band Heater). there is. Therefore, in order to prevent fires from these devices, a system to remove foreign substances inside the water purifier is necessary, the use of heat-resistant (fire-resistant) wires for electrical devices is essential, and the use of non-combustible materials (semi-combustible materials) for each part is necessary to prevent fire. The risk must be eliminated through prevention and combustion expansion prevention devices.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1517-1518
• /
• 2008

Optical disk driver is being used in many electronic products besides computer. In particular, the demands are recently increased as an optical disk player in the mobile products such as camcorder or in the home theater appliances, or etc. However, under these circumstances, the disturbance inputs to the optical disk player increase gradually. In this paper, for reducing the possibility of malfunction of the optical disk player, we propose the method of detecting and controling the non-periodic external shock of the disturbances. Also, we execute some simulations and actual experiments and discuss the results.

• Industrial Engineering and Management Systems
• /
• v.16 no.1
• /
• pp.22-43
• /
• 2017

It is urgently-needed to construct a green supply chain (GSC) from collection of used products through recycling of them to sales of products using the recycled parts. Besides, it is necessary to consider the uncertainty in product demand as a risk in a GSC. This study proposes the optimal operations for a GSC with a retailer and a manufacturer. A retailer pays an incentive for collection of used products from customers and sells a single type of products in a market. A manufacturer produces the products ordered by the retailer, using recyclable parts with acceptable quality and compensates the collection cost of used products as to the recycled parts. This paper discusses the following risk attitudes: risk-neutral attitude, risk-averse attitude, and risk-prone attitude. Using mean-variance analysis, the optimal decisions for product order quantity, collection incentive, and lower limit of quality level, in the decentralized GSC (DGSC) and the integrated GSC (IGSC) are made. DGSC optimizes the utility function of each member. IGSC does that of the whole system. The analysis numerically investigates how (i) risk attitude and (ii) quality of recyclable parts affect the optimal operations. Supply chain coordination between GSC members to shift IGSC from DGSC is discussed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.10
• /
• pp.847-858
• /
• 2000

The aging characteristics of 2 kinds of 3 years field-aged distribution polymer insulators which were dismounted from 5 regions have been investigated by electrical test and material characterization. Although the tan $\delta$of specimens prepared from weathershed was increased with surface aging, the tan $\delta$and leakage current of real products had no difference between virgin and dismounted ones. Due to the aging, all dismounted polymer insulators had micro-cracks on the surface of weathershed and only the products of manufacturer B showed the reduction of OIT(oxidation induction time). But, there were no differences between virgin and dismounted products in contact angle and chemical structure. Therefore, it can be considered that the aging is only limited on the surface of dismounted polymer insulators and that NMR technique are very useful to evaluate the aging of polymer materials.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.1100-1103
• /
• 2001

(1) By comparing and analyzing the distribution of brightness as domestic lamps and Japanese products go thinner and lighter, we set an effective design standard. (2) By comparing and analyzing the feature, brightness, chromaticity and uniformity of domestic LGPs and Japanese products, early home-manufacturing and stabilization in home-manufacturing are possible. (3) By comparing and analyzing the distribution of brightness as sheets are varied, we can design an ideal sheet composition.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.278-283
• /
• 2000

The activity of catalysts obtained by self-propagating high temperature synthesis in reaction of partial methane oxidation at atmospheric pressure was investigated. Basing on the compared results of X-ray analysis and gas chromatography analysis of reaction products, the dependence of compounds formation on the phase concentrations in the studied catalyst samples was found.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.10a
• /
• pp.631-633
• /
• 2000

Modern consumer electronic products like TV, VCR etc, offer users the convience of switching the equipment on and off via a remote control handset. When this type of equipments is switched off, it is said to be in standby mode. In this paper, We proposed that the method of the blocking standby power Son in industrial product including electronic and electronic appliauces. This method is perfectly blocking the standby power of electrical circuit.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.92-95
• /
• 2003

The dissolved oxygen sensors with thick film type were fabricated for low cost products and the electrical properties were investigated in the different operating temperatures. Pt paste was used for working electrode and Ag/AgCl paste for reference electrode. The fabricated devices have fast response of current changes according to dissolved oxygen concentrations in the applied voltage of $0.6{\sim}0.8V$. This is expected to apply a chip and/or disposal dissolved oxygen sensors.

• Clean Technology
• /
• v.15 no.1
• /
• pp.23-30
• /
• 2009

European directive DIRECTIVE 2002/96/EC requires the minimum recycling & recovery rate on the waste electrical and electronic equipments (WEEE). But, they do not have guidelines on the calculation methods for recycling and recovery rate. A standard method to calculate recyclability and recoverability rate of products in the designing stage is necessary for the manufacturers so that they can reflect the calculated result to the improvement of product design. In this work, we investigated the existing calculation methods for the recycling and recovery rates of WEEE and the recyclability and recoverability rates of electrical and electronic equipments (EEE). A method for the calculation of recyclability and recoverability rates for the EEE products in the development stage was developed. The newly-developed calculation method was applied to some EEE products and the calculated results were evaluated.