• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.28-32
• /
• 2004

In this paper, degradation in field-aged PV modules including degradation of interconnect, discoloration of encapsulant and hot spot have been observed and analyzed. From the results, photovoltaic module installed for 6 years shows around 16% drop of electrical properties due to the interconnect degradation and PV module passed 18 years has been found to drop of around 20% mainly by the encapsulant discoloration. Furthermore the difference between low and high temperature of PV array at hot spot goes up to $30^{\circ}C$ and it leads to interconnect degradation. On the other hands, the temperature difference was observed to be around $15^{\circ}C$ at the encapsulant discoloration spot of PV array.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.298-299
• /
• 2006

공통의 glass를 이용한 LTCC 이종소재의 무수축 접합 가능성을 확인하기 위하여 2종의 상용 glass를 이용하여 소결온도를 변화시키면서 미세구조 및 결정구조, x-y축 방향의 수축율을 관찰하였다. 실험 결과 GA-12 glass는 강유전체 $BaTiO_3$와 glass의 composite개념을 이용한 접합에 적절하지 않은 것으로 판단되었으며, GA-1 glass의 경우는 $750^{\circ}C$와 $800^{\circ}C$ 사이에서 glass의 충분한 침투조건이 확인되며, 결정구조 에서도 glass/$BaTiO_3$ composite이 형성되므로 layer 간의 delamination은 발견되지만 x-y축 방향의 무수축 접합의 가능성이 확인되었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.12-13
• /
• 2007

In this paper, we studied the analysis of environmental effects on maximum output power change of crystalline silicon photovoltaic module. During the test period, there was a 5% reduction of maximum output power on an average. And the degree of output power uniformity became better compared to initial value. Using climate data like rain, snow and dust, we tried to find the reasons for maximum power fluctuation. The surface of PV module was monitored using microscope and infrared camera to study temperature distribution. The further analysis is described in the following paper.

• 반도체디스플레이기술학회지
• /
• 제16권2호
• /
• pp.85-88
• /
• 2017

In this paper, we have designed and fabricated a RF-DC voltage multiplier for 5.8GHz microwave wireless power transmission. In order to obtain higher voltage, the RF-DC voltage multiplier with 10 diodes (D-10) and the receiver module with an antenna and BPF (Band Pass Filter) was manufactured. The measured and compared results show that the voltages of the proposed one are lower than those of the previous tripler module up to 40cm. However, the voltage of the proposed one with the voltage multiplier is higher than that of the tripler module at the distances of 45cm and 50cm due to the voltage multiplier with 10 diodes.

• 한국멀티미디어학회논문지
• /
• 제25권4호
• /
• pp.568-574
• /
• 2022

In this paper, direction normalization and CNN deep learning are used to develop a more reliable license plate recognition system. The existing license plate recognition system consists of three main modules: license plate detection module, character segmentation module, and character recognition module. The proposed system minimizes recognition error by adding a direction normalization module when a detected license plate is inclined. Experimental results show the superiority of the proposed method in comparison to the previous system.

• 한국전기전자재료학회논문지
• /
• 제31권5호
• /
• pp.290-294
• /
• 2018

The shingled photovoltaic module can be produced by joining divided solar cells into a string of busbarless structure and arranging them in series and parallel to produce a module, in order to produce a high output per unit area. This paper reports a study to optimize solar cell electrode structure for shingled photovoltaic module fabrication. The characteristics of each electrode structure were analyzed according to the simulation program as follow: 80.62% fill factor in the six-junction solar cell electrode structure and 19.23% efficiency in the five-junction electrode structure. Therefore, the split electrode structure optimized for high-density and high-output shingled module fabrication is the five-junction solar cell electrode structure.

• 한국전자통신학회논문지
• /
• 제10권10호
• /
• pp.1079-1086
• /
• 2015

본 논문은 안전 무결성 레벨이 4(: Safety Integrity Level 4)인 안전 관련 시스템에 적합한 출력 모듈의 구조를 설계하였고, 설계된 출력 모듈에 요구되는 정량적 목표치의 수준을 제시하였다. 특히 다양한 출력 방식 중에서 릴레이 출력 신호와 아날로그 신호로 구성된 출력 모듈이 안전 기능을 수행하는 시스템의 구성 요소인 경우를 적용하였다. 분석 방법은 FMEA(: Failure Modes and Effect Analysis), FTA(: Fault Tree Analysis) 방식을 이용하였다. 그 결과로 철도 응용 규격인 IEC 62425의 요구사항을 준수하는 SIL4 안전 관련 시스템의 출력 모듈의 구조와 고장빈도인 정량적 목표치를 제시하였다.

• 한국전기전자재료학회논문지
• /
• 제23권11호
• /
• pp.901-905
• /
• 2010

PV module has many power loss factors, and series resistance is the most important elements of them. It is therefore easy to expect the partial shading decrease the lifetime of the semiconductor depletion layer in thin film PV module. Different shading losses could be related with the hot spot which is critical in expecting the reliability issue. In this paper we have modelled the series resistance of the PV module with both different direction of the cell line and shading area of the panel. From the results, thin film a-Si PV module has shown different properties by shading direction.

• Journal of Electrical Engineering and Technology
• /
• 제12권4호
• /
• pp.1519-1528
• /
• 2017

The paper proposes a well structured, component count waned single phase multilevel inverter (MLI) topology, which drives three different modules viz. Stipulation Based Sources Insertion (SBSI) module, Level Count Increasing (LCI) module and Inter-Linking H-Bridge (ILHB) module. The SBSI module confronts the number of basic sources needed in series/parallel to achieve required magnitude for any particular level. The LCI possesses an offsetting dc source and opuses to increase the number of levels and the ILHB module links the SBSI and LCI modules. A developed Hybrid Pulse Width Modulation (HPWM) strategy has PWM pulses for the switches of LCI module while the switches of the remaining two modules function at fundamental switching frequency. A fifteen level version of the proposed stipulation based sources insertion MLI (SBSIMLI) topology is simulated in MATLAB R2010a and a prototype of the similar specifications is constructed to validate the performance by experimental results. The comparison between the developed SBSIMLI topology and the competent topologies shows many interesting facts.

• Transactions on Electrical and Electronic Materials
• /
• 제18권1호
• /
• pp.30-34
• /
• 2017

The building integrated photovoltaic system (BIPV) attracts attention with regard to the future of the photovoltaic (PV) industry. It is because one of the promising national and civilian projects in the country. Since land area is limited, there is considerable interest in BIPV systems with a variety of angles and shapes of PV panels. It is therefore expected to be one of the major fields for the PV industry in the future. Since the irradiation is different from each installation angle, the output can be predicted by the angles. This is critical for a PV system to be operated at maximum power and use an efficient design. The development characteristics of tilted angles based on data results obtained via long-term monitoring need to be analyzed. The ratio of the theoretically available and actual outputs is compared with the installation angles of each PV module to provide a suitable PV system for the user.