• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.326-332
• /
• 2000

It should be essentially considered as important points that design of case in electronic product which simultaneously satisfied with structural stability and molding form in respect to developmental period and economical aspect. Especially, a shape of air vents grille, which is made to emit heat happen to be in the internal of product, must satisfy durability and strength but We have no quantitative data because to be done by experience of designer. So, in this study, We will propose that structure of optimal and method of design in air vents grille, which to reduce a lot of loss of time and cost due to trial and error of design and to stabilize in the BALLISTIC Impact test as to estimate strength with external appearance of product, using linear analysis.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.368-371
• /
• 2008

An extensometer system to measure strain and displacement of cylindrical fatigue specimen in a autoclave of high temperature and high pressure environment has been developed by KEPRI. The extensometer reads the displacement caused by fatigue loads at the target length of the specimen installed inside the autoclave. The performance of the extensometer were tested at 15MPa, $315^{\circ}C$ of a operating pressurized water reactor. Two LVDT's of magnet type were connected to the extensometer and used for converting the fatigue displacement to electronic signal. The device is being used for developing environmental fatigue curve of CF8M cast austenitic stainless steel (CASS) in the test condition of low cycle and low strain. This paper introduces the background and results of the development.

• Journal of Power Electronics
• /
• v.9 no.2
• /
• pp.267-274
• /
• 2009

This paper deals with a voltage and frequency (VF) controller for an isolated power generation system based on an asynchronous generator (AG) driven by a pico hydro turbine. The proposed controller is a combination of a static compensator (STATCOM) and an electronic load controller (ELC) for decoupled control of the reactive and active powers of the AG system to control the voltage and frequency respectively. The proposed generating system along with its VF controller is modeled in MATLAB using SIMULINK and PSB (Power System Block Sets) toolboxes. The performance of the controller is verified for the proposed system and feeding various types of consumer load such as linear/non-linear, balanced/unbalanced and dynamic loads.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.2
• /
• pp.35-41
• /
• 2005

Electric ballast is widely used to turn on the fluorescent. Electric ballast measure occurrence of harmonic through the actual measurement and it is simulated by modeling equivalent circuit for harmonic analysis. The purpose of this paper is to give an equivalent circuit modeling methodology for the harmonic currents generated by single-phase loads to evaluate a commercially available series resonant filter for the harmonic currents compensation based on the IEC 61000-3-2 and IEEE Std 519-1992 standards for limiting harmonic distortion.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.185-188
• /
• 2005

The recent growth in the use of impactive and nonlinear loads, electronic devices sensitive to power quality has caused many power quality problems. Dynamic voltage restorers(DVR) are known as the best effective and economic means to compensate for power quality problems(especially, voltage sag and swell). In this paper, we addresses the detecting algorithms of an voltage sag and phase for operating DVR. Experimental results are included to illustrate the efficacy of the proposed algorithm.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.192-194
• /
• 2005

Development of nonlinear loads and compensation instruments make PQ(Power Quality) problem into important issue. Few studies by signal processing and pattern classification as NN(Neural Network), Wavelet Transform, and Fuzzy present feature extraction. A lot of Input features make not always good result and they are difficult to make realtime system. Thus, The dimentionality reduction is indispensable process. PCA(Principal Component Analysis) reduces high-dimensional input features onto a lower-dimensional subspace effectively. It will be useful to apply to realtime system and NN.

• KIEE International Transactions on Power Engineering
• /
• v.4A no.4
• /
• pp.201-206
• /
• 2004

With the advent of distributed generation, power systems in general are impacted in regards to stability and power quality. Distributed generation has positive impacts on system restoration following a fault, higher reliability, and mitigation of effect due to voltage sag. However, distributed generation also has negative impacts on the decrease of reliability such as changes of protective device setting and mal-operation. Because bulk power systems consist of various sources and loads, it is complicated to analyze power systems that have distributed generation. The types of distributed generation usually are classified as the rotating machinery system and the inverter-based system. In this paper, distributed generation is designed as a synchronous generator, and the distribution system with its distributed generation model is simulated using EMTP. In addition, this paper shows the simulation results according to the types of distributed generation

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.02a
• /
• pp.600-606
• /
• 2002

이제까지 전자코 시스템을 이용하여 각각의 식용유에 대한 가열시간과 가열온도에 대한 특성을 분석하였다. 전자코시스템의 센서에서 출력되는 $R_{gas}$/ $R_{air}$를 그래프분석을 통하여 센서가 반응하는 성향을 알 수 있었다. 그리고 주성분 분석의 score plot을 이용하여 PCI의 0을 중심으로 (+)영역에서 가열시간이 짧게 나타나고, (-)영역에서는 가열시간이 길게 나타나는데 이는 가열 시간에 따른 신선도를 예측 할 수 있음을 시사하였다. 그리고 주성분 분석의 loads plot을 이용하여 비슷한 향 성분에 반응하는 각 센서의 성향을 파악 할 수 있었다. 마지막으로 군집분석을 통하여 각 식용유의 종류와 가열온도와 가열 시간에 따른 센서의 상사성을 이용하여 전자코 시스템의 설계에 있어 식용유의 향 특성에 맞는 센서를 선택 시 유용하게 이용 될 것으로 사료된다. 결과적으로 전자코 시스템은 식용유의 유통과 소비과정에서 흔히 발생되는 휘발성 향 특성을 이용하여 가열시간에 따른 식용유의 품질관리와 품질 검사를 비롯한 신선도를 예측할 수 있으며 이를 이용하여 제조 및 유통 그리고 조리 과정에서 보다 효율적으로 사용 될 것으로 예상된다.상된다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.7 no.1
• /
• pp.40-48
• /
• 1983

Nowadays electromagnetic contactors are used for power on-off in various electrical loads. If the severe arc are occurred when power off, the magnetic contactor can not long run because of damage of contactor. In this paper, Authors indicate a method of how to minimize the arc when power off, Authors contrived a electronic circuit which can adjust the demagnetizing point of electro magnetic contactor, and control the demagnetizing point, utilizing our circuit, so as to occur the extinguish of arc at near the AC current zero point which is indispensibly exists. From the results of study, Authors could get confirmations the AC circuit could cut off with occurrence of mininum arc, and that possibility of extensive utilization of our method to hightension circuit.

• Journal of Power Electronics
• /
• v.17 no.6
• /
• pp.1611-1624
• /
• 2017

With the rapid development of microgrid technology, microgrid projects are no longer limited to laboratory demonstrations and pilot platforms. It shows greater value in practical applications. Hence, the smooth interaction between a microgrid and the main grid plays a critical role. In this paper, a control method based on active disturbance rejection control (ADRC) is proposed in order to realize seamless transitions between grid-connected and islanding operation modes and stable operation with variable loads. It is verified by simulations that the proposed ADRC-based method features better performance when compared to conventional proportional-integral-differential (PID) control. Meanwhile, the stability of the third-order extended state observer (ESO) in second-order ADRC is validated by using Lyapunov stability criteria.