• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2006.05a
• /
• pp.127-130
• /
• 2006

사파이어 기판위에 MOCVD (metal organic chemical vapor deposition)를 이용하여 8주기의 InGaN/GaN 다중양자우물(multiple quantum well : MQW)구조가 성장되어졌고 이 구조 위에 p-GaN층이 형성됐다. 다시 p-GaN 위에 200nm의 두께를 갖는 PMMU 박막을 도포하고 electron beam lithography system을 이용하여 직경이 150nm가 되도록 나노단위의 삼각격자 구조를 가진 구멍을 패턴하고 inductively coupled plasma(ICP)를 이용하여 식각을 하여 광결정을 제작하였다. 광결정은 두께가 26nm이고 격자간격은 460nm로서 파장이 450nm인 파란빛을 나노회절 시켜서 photoluminescence(PL)의 세기를 강화시킨다.

• Solar Energy
• /
• v.8 no.1
• /
• pp.68-73
• /
• 1988

In the glass/TCO/p-i-n a-Si/Al type of amorphous silicon solar cell, the effects on solar cell efficiency and metastability for the various kinds of TCO analyzed by SAM and ESCA, which was used to measure the diffusion profiles of In and Sn and the Fermi energy shifts in the TCO/p interface respectively. Indium which diffused into a-Si p-layer did not have any significant effects on the Fermi level shift of p-layer when the content of $B_2H_6/SiH_4$ in p-layer was at 1 gas%. The cell fabricated on $SnO_2$ turned out to have the best cell photovoltaic characteristics. ITO fabricated by electron beam deposition system, which was shown to have the greatest rate of diffusion of Indium in ITO/p interface produced the worst metastability among the cells tested.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2013.05a
• /
• pp.150-150
• /
• 2013

Al-Mg films were prepared onto steel sheet according to deposition condition by eco-friendly electron beam vacuum evaporation method. The influence of Al-Mg films on corrosion resistance was evaluated by salt spray test and electrochemical method etc.. From the experimented results, it was found that the Al-Mg films which showed good corrosion resistance tend to have fine structure with homogenious composition distribution. In addition, it was shown that the property of coating films can be improve by controlling thickness ratio and uniform distribution of intermetallic compounds in Al-Mg films.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.9
• /
• pp.751-756
• /
• 2001

Carbon nanotubes(CNTs) was successfully grown on Ni coated silicon wafer substrate by PECVD technique(Plasma Enhanced Chemical Vapor Deposition). As a catalyst, Ni thin film of thickness ranging from 15∼30nm was prepared by electron beam evaporator system. In order to find the find the optimum growth condition, initially two different types of gas mixtures such as C$_2$H$_2$-NH$_3$ and C$_2$H$_2$-NH$_3$-Ar were systematically investigated by adjusting the gas mixing ratio in temperature of 600$^{\circ}C$ under 0.4 torr. The diameter of the grown CNTs was 40∼200nm. The diameter of the CNTs increases with increasing the Ni particles size. TEM images clearly demonstrated synthesized nanotubes to be multiwalled.

• ETRI Journal
• /
• v.26 no.5
• /
• pp.475-480
• /
• 2004

Self-assembled InAs quantum dots (QDs) embedded in an InAlGaAs matrix were grown on an InP (001) using a solid-source molecular beam epitaxy and investigated using transmission electron microscopy (TEM) and photoluminescence (PL) spectroscopy. TEM images indicated that the QD formation was strongly dependent on the growth behaviors of group III elements during the deposition of InAlGaAs barriers. We achieved a lasing operation of around 1.5 ${\mu}m$ at room temperature from uncoated QD lasers based on the InAlGaAs-InAlAs material system on the InP (001). The lasing wavelengths of the ridge-waveguide QD lasers were also dependent upon the cavity lengths due mainly to the gain required for the lasing operation.

• Solar Energy
• /
• v.19 no.1
• /
• pp.1-8
• /
• 1999

Electrochromic $WO_3$ thin films were prepared by electron beam deposition. The transmission and durability of films were investigated. Coloring and bleaching experiments were repeated in an electrolyte of propylene carbonate with 0.6M of $LiClO_4$ by cyclic voltammetry. Spectrophotometer was used to measure the transmission in the degraded films. The 5000 ${\AA}$ thick film was found to be the stable after repeated cycles. The durability of the annealed film also showed improvements over unannealed samples. Tungsten oxide films with titanium content of about $10{\sim}15$ mol% was found to be most stable, undergoing the least degradation during the repeated cycles.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.663-666
• /
• 2000

Laser direct writing of micro-patterned copper lines has been achieved by pyrolytic decomposition of copper formate films (Cu(HCOO)$_2$$.$4H$_2$O), as a precursor, using a focused Ar$\^$+/ laser beam ($\lambda$= 514 nm) on PCB boards and glass substrates. The linewidth and thickness of the lines were investigated as a function of laser power and scan speed. The profiles of the lines were measured by scanning electron microscope (SEM), surface profiler (${\alpha}$-step) and atomic force microscopy (AFM). The electrical resistivities of the patterned lines were also investigated as a function of laser parameter using probe station and semiconductor analyzer. we compared resistivities of the patterned lines with that of the Cu bulk, respectively.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2003.10a
• /
• pp.136-137
• /
• 2003

In this study, in order to fabricate sintered dental implant, the effects of HA, Ti and TiN on corrosion and biocompatibility, cell toxicity, osseointegration of electroless Cu-plated and sintered stainless steel implant were investigated using various characteristics. The effects of Ti/TiN/HA coating on the interface activation and surface characteristics of sintered stainless steels(SSS) by electron-beam physical vapor deposition(EB-PVD) method have been studied. Stainless steel compacts containing 2, 4, and 10 wt%Cu were prepared by electroless Cu-plating method which results in the increased homogenization in alloying powder. The specimens were coated with HA, Ti and TiN with few $\mu\textrm{m}$ thickness respectively by EB-PVD method. The microstructures and phase analysis were conducted by using SEM. Biocompatibility were investigated in experimental dog. The corrosion behaviors were investigated using potentiosat in 0.9% NaCl solution and corrosion surface was observed using SEM and XPS.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.1
• /
• pp.39-48
• /
• 2001

Fe-Cr-Al alloy has been studied for application in automobile muffler materials due to good corrosion and oxidation resistance. In order to develop the automobile muffler materials, corrosion behaviors of electron beam physical vapor deposition (EB-PVD) coated surface of muffler matericls of muffler materials were investigated using potentiostat. For 0.1M NaCl solution, corrosion potential and pitting potential of Fe-20Cr-10Al was higher than that of Fe-5Cr- 10Al samples. Especially, in the case of Ti and Nb coated samples, pitting potential increased remarkably compared with non-coated samples. For 0.1M $CaCl_2$ solution, Ti-coated Fe-20Cr-10Al showed remarkably improved pitting corrosion resistance in comparison with non-coated Fe-20Cr-10Al and Fe-5Cr-10Al. The number and size of pits were decreased in the case of Ti coated samples in the 0.1M NaCl and 0.1M $CaCl_2$ solution.

• Journal of Welding and Joining
• /
• v.34 no.4
• /
• pp.1-8
• /
• 2016

Metal AM(Additive Manufacturing) has been steadily developed and that is classified into two method. PBF(Powder Bed Fusion) deposited in the bed by the laser or electron beam as a heat source of the powder material and DED(Directed Energy Deposition) deposited by varied heat source of powder and solid filler material. In the developed countries has been applying high productivity process of solid filler metal based DED method to the aerospace and defense sectors. The price of the powder material is quite expensive compared to the solid filler metal. A study on DED method that is based on a solid filler metal is increasing significantly although was low accuracy and degree of freedom.