• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.5
• /
• pp.63-68
• /
• 1999

In this paper, the correlation between the growth mechanism and the optical property in GaN films grown by low-pressure metalorganic chemical vapor deposition was characterized using room temperature cathodoluminescence spectroscopy. An intense near band-edge emission, 364nm, and deep-level emission, 550nm, were observed. The intensity of 364nm peak was increased with increasing the beam current. Also the peak position of 364nm emission was red-shifted and the intensity of 550nm peak was increased with increasing the accelerating voltage. It shows that the deep-level emission is strongly associated with crystalline defects in the GaN at early stage. The relationship between the microstructure and the deep level emission observed by scanning electron microscope images and cathodoluminescence spectra was carefully analyzed.

• Journal of Sensor Science and Technology
• /
• v.25 no.3
• /
• pp.184-188
• /
• 2016

Highly ordered $SnO_2$ and NiO nanocolumns have been successfully achieved by glancing-angle deposition (GLAD) using an electron beam evaporator. Nanocolumnar $SnO_2$ and NiO sensors exhibited high performance owing to the porous nanostructural effect with the formation of a double Schottky junction and high surface-to-volume ratios. When all gas sensors were exposed to various gases such as $C_2H_5OH$, $C_6H_6$, and $CH_3COCH_3$, the response of the highly ordered $SnO_2$ nanocolumn were over 50 times higher than that of the $SnO_2$ thin film. This work will bring broad interest and create a strong impact in many different fields owing to its particularly simple and reliable fabrication process.

• Journal of the Korean Society for Heat Treatment
• /
• v.14 no.5
• /
• pp.292-296
• /
• 2001

In this work, an ultra-high vacuum activated reactive evaporation equipment was built. With reaction of Al and oxygen plasma, $Al_2O_3$ was deposited on the surface of etched Al foil. The chamber was evacuated down to $2{\times}10^{-7}$ torr initially. The Ar and $O_2$ gas introduced into the chamber to maintain $5{\times}10^{-5}$ torr during deposition. Ar gas prevents recombining of the ionized oxygen. Evaporation was maintained by electron beam evaporator continuously. Heating filament and electrode were used in order to generate plasma. The substrate bias of -300V was introduced to accelerate deposition of evaporated Al atoms. The composition and morphology of deposited $Al_2O_3$ films were analyzed by x-ray photoelectron spectroscopy(XPS) and atomic force microscopy (AFM), respectively. The Al oxide was formed on the surface of etched Al foil. According to AFM results, the surface morphology of $Al_2O_3$ film indicates uniform feature. Dielectric characteristic was measured as a function of frequency. Measured withstanding voltage and capacitance were 52V and $24{\mu}F/cm^2$, respectively. The obtained $Al_2O_3$ film shows clean condition without contaminants, which could be adapted to capacitor production.

• Korean Journal of Optics and Photonics
• /
• v.8 no.1
• /
• pp.37-41
• /
• 1997

The optical property, the environmental stability and the crystallization of ZnS thin films prepared by ion-assisted deposition (IAD) were investigated and compared with those of conventional electron-beam deposited thin films. The humidity(R.H. 85%) test and the thermal(15$0^{\circ}C$) show that the IAD films have relatively higher refractive index, smaller extinction coefficient and environmentally more stable than the conventional films. It is believed to originate from the reduced adsorption of moisture which reflect the increased packing density and the improved microstructure by ion bombardment. XRD experiments also confirm that conventionally grown films have an amorphous in comparison with the crystalline structured IAD films.

• Journal of the Korean institute of surface engineering
• /
• v.47 no.6
• /
• pp.347-353
• /
• 2014

We present a synthesis of single-walled carbon nanotubes(SWNTs) for enhancement of parallel-alignment and density using chemical vapor deposition with methane feed gas. As-purchased ST-cut quartz substrates were heat-treated and line-patterned by electron-beam lithography in order to grow SWNTs with parallel alignment. We investigated the effects of various synthesis parameters such as catalyst oxidation, reduction, and synthesis conditions in order to enhance both tube density and degree of parallel alignment. The condition of $1{\AA}$ of Fe catalyst film, atmospheric oxidation at $750^{\circ}C$ for 10 min, reduction under 400 Torr for 5 min, and growth at $865^{\circ}C$ under 300 Torr yields $33tubes/10{\mu}m$, which is the highest tube density with parallel alignment. Based on the results of atomic force microscope and Raman spectroscopy, it was found that SWNTs have diameter range of 0.8-2.0 nm. We believe that the present work would contribute to the development of SWNTs-based flexible functional devices.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.283.2-283.2
• /
• 2014

열필라멘트 화학증착공정(Hot Wire Chemical Vapor Deposition)에서 기상 에서 생성되는 하전된 실리콘 나노입자와 저온결정성 실리콘박막 증착의 연관성을 압력의 변화에 따른 상호비교를 통해 조사하였다. 필라멘트 온도는 $1800^{\circ}C$로 고정시키고 0.3~2 torr의 범위에서 공정 압력을 변화시키면서 증착하였다. 압력이 증가함에 따라 증착된 실리콘 박막의 결정화도는 증가하였으며, 증착속도는 감소하였다. 반응기 압력에 따른 기상에서 생성되는 나노입자의 크기분포의 변화를 조사하기 위하여 탄소막이 코팅된 투과전자현미경(Transmission Electron Microscopy) 그리드 위에 실리콘 나노입자를 포획하고 관찰하였다. 포획된 실리콘 나노입자의 크기분포와 개수농도는 압력이 증가함에 따라 감소하였다. 투과전자현미경을 이용하여 분석한 결과, 나노입자는 결정성 구조를 보였다. 압력이 증가함에 따라 나노입자의 크기가 감소하고 개수농도가 감소하는 것은 증착속도의 감소와 관련됨을 알 수 있다. 한편, 공정압력 증가에 따른 나노입자의 크기분포 및 개수농도 감소와 증착속도의 감소는 일반적으로 알려진 기상에서 석출하는 고상의 평형석출량(equilibrium amount of precipitation)이 압력의 증가함에 따라 증가한다는 사실과 일치하지 않는다. 이러한 압력경향성은 Si-H 시스템이 0.3~2 torr의 압력 영역에서 retrograde solubility를 갖는 것을 의미한다. 나노입자의 하전여부, 크기분포 및 개수농도를 측정하기 위하여 입자빔질량분석장비(Particle Beam Mass Spectroscopy)를 이용하였다. 그 결과, 실리콘 나노입자는 양 또는 음의 극성을 가진 하전된 상태임을 확인하였고, 투과전자현미경(TEM) grid에 포획한 실리콘 나노입자의 크기와 경향성이 일치하였다. 이는 나노입자가 저온의 기판에서 핵생성되어 성장하여 생성된 것이 아니라 열필라멘트 주위의 고온영역에서 생성된 것을 의미한다.

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.202-203
• /
• 2006

In the AC PDP, the MgO film is used as electrode protective film. This film must provide excellent ion bombardment protection, high secondary electron emission, and should be high transparent to visible radiation. In this study, we investigated the relations between the crystal orientation and e-beam evaporation process parameters. The crystal orientation of the MgO layer depends on the conditions of deposition. The parameters are the thickness of the MgO film $1000{\AA}-6500{\AA}$, the deposition rate $200{\AA}/min{\sim}440{\AA}/min$, the temperature $150^{\circ}C{\sim}250^{\circ}C$, and the distance between crucible and substrate 11cm ${\sim}$ 14cm. The temperature of substrate and evaporation rate of source material, or deposition rate of the film, are definitely related to the crystal orientation of the MgO thin film. The crystal orientation can be changed by the distance between the target(MgO tablet) and the substrate. However, the crystal orientation is not much affected by the thickness of MgO thin film.

• Applied Chemistry for Engineering
• /
• v.20 no.6
• /
• pp.612-616
• /
• 2009

Transparent conductive oxide (TCO) films have been widely used in the field of flat panel display industry. Transparent conductive indium zinc oxide (IZO) thin films with excellent chemical stability have attracted much attention as an alternative material for indium tin oxide (ITO) films. In this study, using a $In_2O_3$ and ZnO powder mixture with a ratio of 90 : 10wt% as a target, IZO films were prepared on polynorbornene (PNB) substrates by electron beam evaporation. The effect of substrate temperature and $O_2$ introduction flow rate were investigated in terms of electrical and optical properties of deposited IZO films. The best electrical and optical properties we obtained from this study were sheet resistance value of $5.446{\times}10^2{\Omega}/{\boxempty}$ and optical transmittance of 87.4% at 550 nm at $O_2$ introduction flow rate of 4 sccm, deposition rate of $2{\AA}$/sec, thickness of 1000 $\AA$ and substrate temperature of $150^{\circ}C$.

• Journal of the Korean Vacuum Society
• /
• v.8 no.1
• /
• pp.70-74
• /
• 1999

MgO-CaO protective layers with various composition were prepared by electron beam evaporation to improve the characteristics of conventional pure MgO thin films as a protective layer for AC-PDP. The maximum deposition rate of pure MgO was 1025 $\AA$/min and decreased with increasing [(CaO/(MgO+CaO)] ratio of evaporation starting materials. From XRD analyses, a trend of peak shift to the lower 2$\theta$ angle side was shown as CaO content increased and it stoped when the concentration of CaO was 0.13, which corresponds to the maximum solubility of CaO in MgO. The optimum composition of the protective thin films was Mg 47.1 at%, Ca 1.3 at%, O 51.6 at%, and firing voltage, memory margin and deposition rate of the film with this composition was 176 V, 0.5 and 515 $\AA$/min, respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.305-305
• /
• 2010

It is known that a pulse of electrons of high kinetic energy (1-3 eV) in metals can be generated with the deposition of external energy to the surface such as in the absorption of light or in exothermic chemical processes. These energetic electrons are not in thermal equilibrium with the metal atoms and are called "hot electrons" The concept of photon energy conversion to hot electron flow was suggested by Eric McFarland and Tang who directly measured the photocurrent on gold thin film of metal-semiconductor ($TiO_2$) Schottky diodes [1]. In order to utilize this scheme, we have fabricated metal-semiconductor Schottky diodes that are made of Pt or Au as a metallic layer, Si or $TiO_2$ as a semiconducting substrate. The Pt/$TiO_2$ and Pt/Si Schottky diodes are made by PECVD (Plasma Enhanced Chemical Vapor Deposition) for $SiO_2$, magnetron sputtering process for $TiO_2$, e-beam evaporation for metallic layers. Metal shadow mask is made for device alignment in device fabrication process. We measured photocurrent on Pt/n-Si diodes under AM1.5G. The incident photon to current conversion efficiency (IPCE) at different wavelengths was measured on the diodes. We also show that the steady-state flow of hot electrons generated from photon absorption can be directly probed with $Pt/TiO_2$ Schottky diodes [2]. We will discuss possible approaches to improve the efficiency of photon energy conversion.