• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.3 no.1
• /
• pp.18-25
• /
• 1978

The 1/f noise spectrum of short-circuited output drain current due to the Shockley-Read-Hal] recombination centers with a single lifetime in homogeneous nondegenerate MOS-field effcte transtors with n-type channel is calculated under the assumptions that the quasi-Fermi level for the carriers in each energy band can not be defined if we include the fluctuation for time varying quantities. and so 1/f noise is a majority carrier effect. Under these assumptions the derived 1/f noise in this paper show some essential features of the 1/f noise in MOS-field effect transistors. That is, it has no lowfrequency plateau and is proportionnal to the channel cross area A and to the driain bias voltage Vd and inversely proportional to the channel length L3 in MOS field effect transistors. This model can explain the discrepancy between the transition frequency of the noise spectrum from 1/f- response to 1/f2 and the frequency corresponding to the relaxation time related to the surface centers in p-n junction diodes. In this paper the results show that the functional form of noise spectrum is greatly influenced by the functional forms of the electron capture probability cn (E) and the relaxation time r (E) for scattering and the case of lattice scattering show to be responsible for the 4 noise in MOS fold effect transistors. So we canconclude that the source of 1/f noise is due to lattice scattering.

• The Journal of Advanced Prosthodontics
• /
• v.1 no.3
• /
• pp.113-117
• /
• 2009

STATEMENT OF PROBLEM. Recently Yttrium-stabilized tetragonal zirconia polycrystal (Y-TZP) has been introduced due to superior flexural strength and fracture toughness compared to other dental ceramic systems. Although zirconia has outstanding mechanical properties, the phenomenon of decrease in the life-time of zirconia resulted from degradation in flexural strength after low temperature aging has been reported. PURPOSE. The objective of this study was to investigate degradation of flexural strength of Y-TZP ceramics after various low temperature aging treatments and to evaluate the phase stability and micro-structural change after aging by using X-ray diffraction analysis and a scanning electron microscope (SEM). MATERIAL AND METHODS. Y-TZP blocks of Vita In-Ceram YZ (Vita Zahnfabrik, Bad $S\ddot{a}ckingen$, Germany) were prepared in 40 mm (length) $\times$ 4 mm (width) $\times$ 3 mm (height) samples. Specimens were artificially aged in distilled water by heat-treatment at a temperature of 75, 100, 125, 150, 175, 200, and $225^{\circ}C$ for 10 hours, in order to induce the phase transformation at the surface. To measure the mechanical property, the specimens were subjected to a four-point bending test using a universal testing machine (Instron model 3365; Instron, Canton, Mass, USA). In addition, X-ray diffraction analysis (DMAX 2500; Rigaku, Tokyo, Japan) and SEM (Hitachi s4700; Jeol Ltd, Tokyo, Japan) were performed to estimate the phase transformation. The statistical analysis was done using SAS 9.1.3 (SAS institute, USA). The flexural strength data of the experimental groups were analyzed by one-way analysis of variance and to detect statistically significant differences ($\alpha$= .05). RESULTS. The mean flexural strength of sintered Vita In-Ceram YZ without autoclaving was 798 MPa. When applied aging temperature at below $125^{\circ}C$ for 10 hours, the flexural strength of Vita In-Ceram YZ increased up to 1,161 MPa. However, at above $150^{\circ}C$, the flexural strength started to decrease. Although low temperature aging caused the tetragonal-to-monoclinic phase transformation related to temperature, the minimum flexural strength was above 700 MPa. CONCLUSION. The monoclinic phase started to appear after aging treatment above $100^{\circ}C$. With the higher aging temperature, the fraction of monoclinic phase increased. The ratio of monoclinic/tetragonal + monoclinic phase reached a plateau value, circa 75% above $175^{\circ}C$. The point of monoclinic concentration at which the flexural strength begins to decrease was between 12% and 54%.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.26 no.6
• /
• pp.225-231
• /
• 2016

The valence band maximum (VBM) and conduction band minimum (CBM) of Al-doped GaInAsSb alloys substrated on GaSb are calculated by using an analytic approximation based on the tight binding method. The relative positions of the VBM and CBM between Al-GaInASSb and GaSb determine band alignement type, valence band offset (VBO) and conductin band offset (CBO) for the heterojunctions. In this study, aluminium doping is assumed to be substituted in the cation site and limited up to 20 % because it can easily oxidize and degrade materials. It is found that the Al-doped alloys exhibit type-II band alignments over the entire composition range and make the band gaps increase, whereas the VBO and CBO decrease. The decreasing rate of VBO is higher than that of CBO, which implies the Al components play a decisive role in controlling electrons at the interface. The Al-dopled GaInAsSb alloy has a direct band gap induced by $E({\Gamma})$ with a considerable distance from the E(L) and E(X), however, $E({\Gamma})$ approaches to E(L) and E(X) in the high Sb concentration (Sb > 0.7-0.8) which might affect the electron mobility and degrade the optical quality.

• Korean Chemical Engineering Research
• /
• v.49 no.2
• /
• pp.250-255
• /
• 2011

In this study, by using the polymeric membrane separation process, the $CO_{2}/CH_{4}$ separation and $H_{2}S$ removal from biogas were performed in order to $CH_{4}$ purification and enrichment for the fuel cell energy source application. Fibers were spun by dry/wet phase inversion method. The module was manufactured by fabricating fibers after surface coating with silicone elastomer. The scanning electron microscopy(SEM) studies showed that the produced fibers typically had an asymmetric structure; a dense top layer supported by a porous, sponge substructure. The permeance of $CO_{2}$ and $CO_{2}/CH_{4}$ selectivity increased with pressure and temperature. Mixture gas with increasing pressure and temperature, removal efficiency of the $CO_{2}$ and $H_{2}S$ were decreased while concentration of $CH_{4}$ was increased up to 100%. When retentate flow rate was increased with the decreasing of pressure and temperature the $CH_{4}$ recovery ratio in retentate side was increased while the $CH_{4}$ purity in retentate side was decreased.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.6
• /
• pp.261-265
• /
• 2010

In this paper, we attempt to improve the electrical characteristics of epoxy resin at high temperature (above $80^{\circ}C$) by adding magnesium oxide (MgO), which has high thermal conductivity. Scanning electron microscopy (SEM) of the dispersion of specimens with added MgO reveals that they are evenly dispersed without concentration. The dielectric breakdown characteristics of $SiO_2$ and MgO nanocomposites are tested by measurements at different temperatures to investigate the filler's effect on the dielectric breakdown characteristics. The dielectric breakdown strength of specimens with added $SiO_2$ decreases slowly below $80^{\circ}C$ (low temperature) but decreases rapidly above $80^{\circ}C$ (high temperature). However, the gradient of the dielectric breakdown strength of specimens with added MgO is slow at both low and high temperatures. The dielectric breakdown strength of specimens with 0.4 wt% $SiO_2$ is the best among the specimens with added $SiO_2$, and that of specimens with 3.0 wt% and 5.0 wt% MgO is the best among those with added MgO. Moreover, the dielectric strength of specimens with 3.0 wt% MgO at high temperatures is approximately 53.3% higher than that of specimens with added $SiO_2$ at $100^{\circ}C$, and that of specimens with 5.0 wt% of MgO is approximately 59.34% higher under the same conditions. The dielectric strength of MgO is believed to be superior to that of $SiO_2$ owing to enhanced thermal radiation because the thermal conductivity rate of MgO (approximately 42 $W/m{\cdot}K$) is approximately 32 times higher than that of $SiO_2$ (approximately 1.3 $W/m{\cdot}K$). We also confirmed that the allowable breakdown strength of specimens with added MgO at $100^{\circ}C$ is within the error range when the breakdown probability of all specimens is 40%. A breakdown probability of up to 40% represents a stable dielectric strength in machinery and apparatus design.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.2
• /
• pp.63-67
• /
• 2010

The organic solar cells with Glass/ITO/PEDOT:PSS/P3HT:PCBM/Al structure were fabricated using regioregular poly (3-hexylthiophene) (P3HT) polymer:(6,6)- phenyl $C_{61}$-butyric acid methyl ester (PCBM) fullerene polymer as the bulk hetero-junction layer. The P3HT and PCBM as the electron donor and acceptor materials were spin casted on the indium tin oxide (ITO) coated glass substrates. The optimum mixing concentration ratio of photovoltaic layer was found to be P3HT:PCBM = 4:4 in wt%, indicating that the short circuit current density ($J_{SC}$), open circuit voltage ($V_{OC}$), fill factor (FF) and power conversion efficiency (PCE) values were about 4.7 $mA/cm^2$, 0.48 V, 43.1% and 0.97%, respectively. To investigate the effects of the post annealing treatment, as prepared organic solar cells were post annealed at the treatment time range from 5min to 20min at $150^{\circ}C$. $J_{SC}$ and $V_{OC}$ increased with increasing the post annealing time from 5min to 15min, which may be originated from the improvement of the light absorption coefficient of P3HT and improved ohmic contact between photo voltaic layer and Al electrode. The maximum $J_{SC},\;V_{OC}$, FF and PCE values of organic solar cell, which was post annealed for 15min at $150^{\circ}C$, were found to be about 7.8 $mA/cm^2$, 0.55 V, 47% and 2.0%, respectively.

• Journal of Environmental Science International
• /
• v.15 no.1
• /
• pp.85-94
• /
• 2006

The simultaneous analysis of multi-residual pesticides was developed using a gas chromatography (GC) method. In this study, a simple and reliable methodology was improved to detect 154 kinds of pesticides in sinseng extract sample by using a liquid-liquid extraction procedure, open column chromagraphy and chromatographic analysis by CC electron capture detector (ECD) and GC nitrogen-phosphorus detector (NPD). The 154 kinds of pesticides were classified in 4 groups according to the chemical structure. The extraction of pesticides was experimented with $70\%$ acetone and dichloromethane/petroleum ether in order, and cleaned up via open column chromatography $(3\times30cm)$ packed with florisil $(30g,\;130^{\circ}C,\;12hrs)$. The final extract was concentrated in a rotator evaporator at $40^{\circ}C$ until dryness. Then the residue was redissolved to 2ml with acetone, and analyzed by GC-ECD and GC-NPD. The applied concentration of pesticides was over $1\~10{\mu}g/ml$. The recovery tests were ranged from $70.7\%$ to $115.2\%$ with standard deviations between 0.3 and $5.7\%$ of the standard spiked to the ginseng extract sample (Group $I\~IV$). The limit of detection (LOD) ranged from 0.001 to $0.099{\mu}g/ml$ (Group $I\~IV$). The 9 kinds of pesticides were not detected. The developed method was applied satisfactory to the determination of the 154 kinds of pesticides in the ginseng extract with good reproducibility and accuracy.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.30 no.1
• /
• pp.80-91
• /
• 2003

Mutans streptococci, especially S. mutans and S. sobrinus strongly implicated in pathogenesis of dental caries, the major cause of tooth loss in children. Use of an antibacterial agent controlling dental caries has been rationalized. The present study was performed to observe the antibacterial effect of inorganic polyphosphates (polyP) on S. mutans and S. sobrinus. S. mutans GS5 and S. sobrinus 6715 were grown in brain-heart infusion broth with or without polyP. Minimal inhibitory concentration (MIC) of polyP for S. mutans GS5 was determined to be 0.08% and that for S. sobrius 6715 was 0.17%. PolyP 15 added to the growing culture of S. mutans GS5 and S. sobrinus 6715 at their exponential phase was as effective in inhibiting the growth of S. mutans GS5 and S. sobrinus 6715 as polyP added at the very beginning of the culture. More than 85% of the cells lost their viability determined by viable cell count when polyP 15 was added to the culture of growing S. mutans GS5 at MIC, suggesting that polyP 15 has bacterial effect on the bacterium. And more than 99.9% of the cells lost their viability determined by viable cell count when polyP 15 was added to the culture of growing S. sobrinus 6715 at MIC, suggesting that polyP 15 has bacterial effect on the bacterium. Intracellular nucleotide release from S. mutans CS5 and S. sobrinus 6715 was increased in the presence of polyP 15 for 5h but was not really reversed by the addition of divalent cations like $Ca^{++}\;and\;Mg^{++}$. The majority of the cells appeared to be atypical in their shape, demonstrating accumulation of highly electron-dense granules and ghost cells. The overall results suggest that polyP have a strong bactericidal activity against S. mutans and S. sobrinus in which lysis in relation to chelation may not play the major role but unknown mechanism that possibly affects the viability of the bacterium may be involved. PolyP may be used as an agent for prevention of dental caries.

• Journal of Electrochemical Science and Technology
• /
• v.11 no.2
• /
• pp.172-179
• /
• 2020

The impact of effective parameters on the electrodeposition rate optimization of Au-Cu alloy at high thicknesses on the silver substrate was investigated in the present study. After ensuring the formation of gold alloy deposits with the desired and standard percentage of gold with the cartage of 18K and other standard karats that should be observed in the manufacturing of the gold and jewelry artifacts, comparing the rate of gold-copper deposition by direct and pulsed current was done. The rate of deposition with pulse current was significantly higher than direct current. In this process, the duty cycle parameter was effectively optimized by the "one factor at a time" method to achieve maximum deposition rate. Particular parameters in this work were direct and pulse current densities, bath temperature, concentration of gold and cyanide ions in electrolyte, pH, agitation and wetting agent additive. Scanning electron microscopy (SEM) and surface chemical analysis system (EDS) were used to study the effect of deposition on the cross-sections of the formed layers. The results revealed that the Au-Cu alloy layer formed with concentrations of 6gr·L^-1 Au, 55gr·L^-1 Cu, 24 gr·L^-1 KCN and 1 ml·L^-1 Lauryl dimethyl amine oxide (LDAO) in the 0.6 mA·cm^-2 average current density and 30% duty cycle, had 0.841 ㎛·min^-1 Which was the highest deposition rate. The use of electrodeposition of pure and alloy gold thick layers as a production method can reduce the use of gold metal in the production of hallow gold artifacts, create sophisticated and unique models, and diversify production by maintaining standard karats, hardness, thickness and mechanical strength. This will not only make the process economical, it will also provide significant added value to the gold artifacts. By pulsating of currents and increasing the duty cycle means reducing the pulse off-time, and if the pulse off-time becomes too short, the electric double layer would not have sufficient growth time, and its thickness decreases. These results show the effect of pulsed current on increasing the electrodeposition rate of Au-Cu alloy confirming the previous studies on the effect of pulsed current on increasing the deposition rate of Au-Cu alloy.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.43 no.10
• /
• pp.1535-1542
• /
• 2014

This study was conducted to investigate the physicochemical properties and biological activities of collagens with different molecular weights from Alaska pollack (Theragra chalcogramma) skin as well as their efficacies as functional materials. The molecular weights of collagens were between 1~10 kDa (below 1 kDa (AP1), 1~3 kDa (AP2), 3~10 kDa (AP3), and above 10 kDa (AP4). The protein content of AP4 (40.19 g/100 g) was the highest. Collagen contents of AP1, AP2, AP3, and AP4 were 36.43, 32.23, 19.23, and 14.89%, respectively. The free amino acid and essential amino acid contents of AP1 were higher than those of AP2, AP3, and AP4. Fourier transform infrared spectroscopy spectra of collagens with different molecular weights showed wavenumbers representing the regions of amide I, amide II, amide III, and amide A, respectively. The electron-donating ability (29.51%) and SOD-like activity (38.45%) of AP1 were higher than those of AP2, AP3, and AP4. Tyrosinase inhibition activity of AP1 improved with higher treatment concentration. The rate of inhibition of MMP-1 production in HS68 cells exposed to UVB was suppressed by treatment with AP1 (29.78%) and AP2 (26.49%) at 1 mg/mL. Furthermore, there was a strong correlation between DPPH, superoxide dismutase, tyrosinase activity, and MMP-1 inhibition rate of collagens with different molecular weights.